Question about 2004 Chevrolet Suburban

Open Question

Need to reset the keyless entry to car doors for chevy '04 suburban. It can be done by owner within the car. Thanks, Eric

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Purchased a 2007 MKZ and there was no owner's card to get the keyless lock code. How can I get it so I can set my doors?


The keyless entry code should be printed on a label by the fuse box. I have attached a picture of where you should find the label SECTION 501-14: Handles, Locks, Latches and Entry Systems 2007 Fusion/Milan/MKZ Workshop Manual GENERAL PROCEDURES Procedure revision date: 07/31/2006 Keyless Entry Keypad Code Programming adobe.gif Printable View (109 KB) NOTE: To associate a memory configuration to a personal entry code, refer to the Owner's Literature.
  1. Enter the permanent factory keyless entry keypad code.
  1. NOTE: Holding the 1/2 button for more than 2 seconds after activation erases all the customer codes. The existing code does not need to be erased to program a new code.
    Press the 1/2 button within 5 seconds to activate the programming mode.
  1. Within 5 seconds, enter the new 5-digit keyless entry keypad code. The doors lock and unlock to confirm the new code is programmed.

2010&c18=modelyear&c20=n996353&c35=wsm%2ckeyless%20entry%20keypad%20code%20programming%2cs7s%2c501-14%2cgeneral%20procedures&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=428&ct=lan&hp=n&[aqe] ddll111_2.jpg

Mar 10, 2011 | Lincoln MKZ Cars & Trucks

3 Answers

How do I reprogram the keyless entry keypad?


You can found the code on F-150 up under the dash. There is a sticker on a grey box. That is the code that you need to open the door. You can then use that code to program your own 5 digit code that you will remember.

For program your keyless pad (clic image), check the procedure in your 2006 Ford F-150 Owners Manual moz-screenshot.pngmoz-screenshot-1.png(page 108 and next).

ec44e90.jpg

Remember rated this help, good luck.

Feb 15, 2010 | 2006 Ford F-150

2 Answers

How do i reprogram keyless entry codes


door pad keyless codes?

in owner manual, enter permanent code and then press "1" and enter personal code, then press "1" again. Then both codes will work.

If you don't have manual, go to Motorcraft.com and click on technical resources and click on your year owner manual.

---------------------------------------------
Each vehicle equipped with a keyless entry keypad is programmed with a five-digit entry code. This code is provided to the customer through a wallet card in the Owner Literature package. In addition, this code is available through a diagnostic tool and is also printed on the vehicle security module label. When entering codes each digit must be entered within five seconds of the previous button press.
Programming/Erasing Personal Code
A unique personal five-digit code can be programmed by following these steps:
  1. Enter the factory set five-digit code (the keypad will illuminate when pressed).
  1. Press 1/2 within five seconds of Step 1.
  1. Enter the unique five-digit code.
The personal code does not substitute for the permanent factory set code. Either code can be used to access the vehicle. In addition, if a second personal code is programmed, it will simply overwrite the previous personal code. To erase a personal code, carry out the following procedure:
  1. Enter factory set five-digit code.
  1. Press 1/2 within five seconds of Step 1.
  1. Press 7/8 and 9/0 at the same time within five seconds of Step 2.
The system will now only respond to the factory set code.
Anti-Scan Feature
To provide added security, the keyless entry pad is disabled for one minute after 35 button presses without a valid entry code being entered. The keypad will flash during this one-minute mode with all functionality disabled except for 7/8 and 9/0 still being allowed to lock the vehicle.
Anti-Scan will be turned off after any of the following events:
  • one minute of keypad inactivity
  • the keyless entry remote transmitter UNLOCK button is pressed
  • the ignition is turned to the ON position.
Unlocking the Doors with the Keyless Entry Keypad System
To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will illuminate.
To unlock all doors, enter either the factory set code or the personal code (driver door unlocks) and press the 3/4 control within five seconds.
Locking the Doors with the Keyless Entry Keypad System
It is not necessary to enter the factory set or personal code prior to locking all doors. To lock all doors, press the 7/8 and 9/0 controls at the same time.
Inspection and Verification
  1. Verify the customer concern by operating the system.
  1. Visually inspect for obvious signs of mechanical or electrical damage.

Dec 01, 2009 | 2004 Ford F350

3 Answers

LHJ001 WIRING


I have the 1995-97 Lincoln Continental Alarm, Remote Starter, Keyless Entry Wiring, review it:

b94b6e9.png


Hope helped.

Oct 30, 2009 | 1996 Lincoln Continental

1 Answer

Keypad door lock does not work..?


it's in owner manual. But, first you have to enter your original code and it must work. then you press the 1 button and then enter a new 5 digit code, then press the 1 button again.

Keyless Entry Keypad To unlock the driver front door (20124) , and disarm the anti-theft alarm control (19A366) , (if equipped):
  • Enter the permanent factory code.
  • Enter the owner's alternate code.
To unlock the passenger door(s), press the 3/4 button within five seconds of unlocking the driver door or luggage compartment. To unlock the luggage compartment door (40110), press the 5/6 button within five seconds of unlocking driver or passenger door(s). To turn on the courtesy lamps and light all illuminated components, lift either front door handle (22404) or press any button on the keyless entry keypad (14A626) . To lock all doors, press the 7/8 and 9/0 buttons at the same time with all doors closed. (It is not necessary to enter the key code first.) This will turn off courtesy lamps and arm anti-theft alarm control (if equipped). To program an alternate code:
  1. Enter the five digit permanent entry code into keyless entry keypad .
  1. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code.
  1. Enter any alternate five digit code within five seconds of pressing 1/2 button.
    • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code:
      • 9/0 — no memory recall
      • 1/2 — memory seat position 1
      • 3/4 — memory seat position 2
      • 5/6 — memory seat position 3
    • After successful programming, the doors will signal by locking and then unlocking.
---------------------------------------------
  • Keyless Entry Keypad Does Not Work Properly
  • Circuit.
  • Keyless entry keypad.
  • Electronic door lock control processor.

  • Open Fuses:
    • Town Car and Crown Victoria/Grand Marquis
    • Power Distribution Box (under hood)- K, 40A (Maxi)
    • Instrument Panel Fuse Panel - 17 (10A), 10 (20A), 8 (15A), 5 (15A) and 4 (10A)
  • Loose Connectors
  • Corroded Connectors
  • Oct 04, 2009 | 1995 Lincoln Town Car

    2 Answers

    Program fob


    Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
    1. Close all the vehicle doors.
    2. Insert the ignition key into the ignition lock cylinder.
    3. Press and hold the DOOR unlock switch.
    4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
    5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
    6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
    7. Repeat the previous step to program up to four transmitters.
    8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
    9. Operate the transmitter functions in order to verify correct system operation

    Apr 19, 2009 | 1999 Chevrolet Silverado 1500

    1 Answer

    Help with finding keyless door pad codes and resetting


    Open the trunk and up under the package tray where rear speakers mount,on the passenger side you will see the module.It will be black and have 3 connectors to it.It will have a sticker on it with a 5 digit code.It will also have a sticker on one of the trunk hindges with this code if someone has not removed it.Here is how the system works:

    Keyless Entry Keypad To unlock the driver front door (20124), and disarm the anti-theft alarm control (19A366) (if equipped):
    • Enter the permanent factory code.
    • Enter the owner's alternate code.
    To unlock the passenger door(s), press the 3/4 button within five seconds of unlocking the driver front door or luggage compartment door (40110) . To unlock the luggage compartment door, press the 5/6 button within five seconds of unlocking the driver or passenger door(s). To turn on the interior lamps (13776) and light all illuminated components, lift either front door handle (22404) and press any button on the keyless entry keypad (14A626) . To lock all doors, press the 7/8 and 9/0 buttons at the same time. (It is not necessary to enter the key code first.) This will turn off courtesy lamps. To program a temporary code:
    • Enter permanent code.
    • Within five seconds of pressing last button of permanent code, press 1/2 button.
    • Enter any alternate five-digit code within five seconds of pressing 1/2 button.

    Apr 15, 2009 | 1995 Ford Taurus

    2 Answers

    Reprogram a keyless entry remote


    Hello
    this is how to program the remotes/keyless entry

    How
    • Obtain all remote transmitters
    • enter the 5 digit permanent code into the keyless entry pad on the drivers door
    • Press the 1-2 switch on the keyless entry pad
    • Within 5 seconds
    • Press any button on the first remote transmitter
    • The doors should open then lock
    • Within 5 seconds
    • press any button on the second & third remote
    • within 5 seconds for each remote
    • to exit programming
    • simultanionusly press 7-8 & 9-0 switchs on the key pad or wait more then 7.5 seconds
    NOTE
    The 5 digit permanent code is located in one of the following places
    1. On the owners warranty card
    2. On the label on the inside the trunk/ boot
    3. On the owners code card
    4. On the centrel locking control module located in the drivers door
    5. In the PCM ford can get this for about $25.00
    I hope this help
    Regards Paul
    www.limotec.co.uk

    Jan 13, 2009 | 1995 Lincoln Town Car

    1 Answer

    96 chevy suburban no automatic door opener alarm activated


    get a jimmy and unlock the door that way the raise the hood and take the pos cable off

    Dec 06, 2008 | 1996 Chevrolet Suburban

    1 Answer

    Reprograming a keyless remote


    program transmitter code(s) as follows:
    1) Confirm that all the doors are closed and the ignition key is out of the ignition cylinder.
    2) Open the driver’s door. Insert the key and turn the ignition switch to ON position within 10 seconds.
    3) Turn the ignition switch to OFF position within 10 seconds, remove ignition key from lock cylin-der.
    4) Push and release the driver’s door switch (1) 3 times within 20 seconds.
    5) Insert the ignition key and turn the ignition switch to ON position within 10 seconds.
    6) Turn the ignition switch to OFF position within 10 seconds, remove ignition key from lock cylin-der.
    7) Press and hold both LOCK and UNLOCK buttons (2) on the transmitter (3) for more than 5 seconds
    within 20 seconds of removing the ignition key from the lock cylinder in step 6.
    8) Press LOCK or UNLOCK button (2) on the transmitter (3) within 5 seconds (after step 7). All the
    doors will lock/ unlock to confirm that this process has been properly done.
    With this process, the transmitter has been programmed.
    9) If you want to program an additional transmitter, repeat the procedure from Step 1) through Step 8).
    10) Make sure that the keyless entry system properly operates by operating each transmitter.

    Nov 08, 2008 | 2000 Chevrolet Tracker

    Not finding what you are looking for?
    2004 Chevrolet Suburban Logo

    Related Topics:

    106 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75066 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7754 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...