Question about 1995 Dodge Neon

1 Answer

How do i install right rear strut - 1995 Dodge Neon

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

They are two bolt's that run trought remove them then the brake line bolt i think there's one more bolt at back of hub if not repost i will look tommrow to see for sure

Posted on Oct 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1996 buick regal custom has no coil springs on rear how do i change the shocks


26083109-sgzmnh3u5bmrsfnwqwi1so0h-1-0.gif Removal:
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle with jackstands.
  3. Remove the rear wheel and tire assembly.
  4. Scribe the strut-to-knuckle for proper installation.
  5. If equipped, remove the auxiliary spring, as outlined in this section.
  6. Remove the jack pad.
  7. Install rear leaf spring compressor tool J-35778, or equivalent. Refer to the Transverse Spring Assembly procedures in this section for installation details.
  8. Fully compress the spring, but do NOT remove the retention plates or the spring.
  9. Unfasten the two strut-to-body bolts.
  10. Remove the brake hose bracket from the strut.
  11. Remove the strut and auxiliary spring upper bracket from the knuckle.
To install:
  1. Position the strut to the body and knuckle bracket.
  2. Install the strut-to-body bolts and tighten to 34 ft. lbs. (46 Nm).
  3. Install the strut to the knuckle, aligning the scribe marks and tighten the bolts to 133 ft. lbs. (180 Nm) for 1988-94 vehicles. For 1995-96 vehicles, tighten the bolts to 122 ft. lbs. (165 Nm).
  4. Install the brake hose bracket.
  5. Remove the spring compressing tool.
  6. Install the jack pad and tighten the retaining bolts to 18 ft. lbs. (25 Nm).
  7. If equipped, install the auxiliary spring.
  8. Install the wheel and tire assembly and install the lug nuts finger-tighten
  9. Carefully lower the vehicle, then tighten the lug nuts to 100 ft. lbs. (136 Nm).
  10. Connect the negative battery cable.

Feb 05, 2016 | Buick Cars & Trucks

1 Answer

2000 Monte Carlo Right rear strut needs to be replaced. Do both rear struts need replacing.Is it DIY or garage job? Cost? Thanks


you tube clips can help you replace rear struts.i would replace both struts same time and call auto parts for struts prices.

Sep 23, 2013 | 2000 Chevrolet Monte Carlo

1 Answer

How to replace the shocks on my 2000 Mazda 626


REMOVE**** FRONT SHOCKS, FIRST OF ALL.SUPPORT THE LOWER CONTROL ARM WITH A JACK,REMOVE FRONT WHEEL, REMOVE BRAKE HOSE AND ABS SENSOR HARNESS TO THE STRUT BOLTS OR CLIPS,REMOVE ACTUATOR FROM TOP OF THE STRUT,IF EQUIPPED WITH AUTOMATIC ADJUSTING SUSPENSION. PAINT ALIGNMENT MARKS ON THE UPPER STRUT MOUNTING BLOCK AND STRUT TOWER AND ON THE LOWER STRUT MOUNT TO STEERING KNUCKLE SO THAT CAN BE REINSTALLED IN THE SAME POSITION. REMOVE UPPER STRUT MOUNTING NUTS, REMOVE THE STRUT TO KNUCKLE BOLTS,REMOVE STRUT ASSEMBLY.TO INSTALL ***** INSTALL STRUT INTO THE STRUT TOWER ALIGNING THE PAINT MARKS MADE DURING REMOVAL.INSTALL UPPER MOUNTING NUTS AND TIGHTEN TO 34 - 46 FT LBS. INSTALL STRUT TO KNUCKLE BOLTS TIGHTEN TO 55 - 61 FT LBS. INSTALL ACTUATOR AND ENGAGE THE ELECTRICAL CONNECTOR IF EQUIPPED WITH AAS. INSTALL BRAKE HOSE AND ABS SENSOR HARNESS CLIPS OR BOLTS.INSTALL WHEEL AND CHECK ADJUST THE FRONT END ALIGNMENT. TO ( REPLACE REAR SHOCKS ) REMOVE REAR WHEELS, REMOVE REAR PACKAGE TRIM. REMOVE SPEED SENSOR HARNESS, REMOVE TOP STRUT NUTS,THE SUSPENSION WILL DROP WHEN THE WEIGHT LIFTS OFF THE WHEELS. REMOVE BOTTOM STRUT BOLTS.REMOVE STRUT ASSEMBLY.TO INSTALL ***** INSTALL STRUT ASSEMBLY, INSTALL BOTTOM STRUT MOUNT BOLTS AND TIGHTEN TO 55 - 61 FT LBS.INSTALL UPPER MOUNTING NUTS AND TIGHTEN TO 33 - 46 FT LBS. INSTALL SPEED SENSOR HARNESS.INSTALL REAR PACKAGE TRIM. INSTALL REAR WHEELS.

Sep 22, 2010 | Mazda 626 Cars & Trucks

2 Answers

2008 elantra suspension clunks in the rear


depending on mileage and relationship you have with your dealer, the rear struts may still be under warranty. 24,000 miles if i remember right. those are your issues. replace the rear struts. cheers

Jan 22, 2010 | 2008 Hyundai Elantra

1 Answer

How do I change the rear shock on my 1999 Dodge Neon?


  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Unfasten the retainer(s), then remove the hydraulic flex hose bracket from the strut bracket. If equipped with ABS, the wheel speed sensor cable routing clip is also attached to the strut assembly bracket.
  1. Support the rear knuckle, suspension and brake components before removing the clevis bracket-to-knuckle attaching bolts. Do NOT allow the weight of the knuckle and related components hang without support when the strut is removed.


  2. WARNING The knuckle-to-strut attaching bolts are serrated and must not be turned during removal. Remove the nuts while holding the bolts stationary in the knuckle.
  1. Hold the bolt with a wrench, then unfasten the 2 clevis bracket nuts attaching the strut to the knuckle.
Fig. Fig. 2: Location of the knuckle-to-clevis bracket bolts


  1. Carefully lower the vehicle, then open the trunk. Access to the rear upper strut mount-to-strut tower attaching bolts is through the trunk of the car.
  2. If necessary, remove the carpet from the top of the strut tower. Then, remove the rubber dust shield from the top of the strut tower for easier access to the upper strut nuts.
  1. Loosen, but do not remove the 4 upper strut mounting nuts. Then, while supporting the strut assembly, fully remove the 4 strut mount attaching nuts.
  1. Remove the strut assembly from the knuckle by sliding the knuckle out of the clevis bracket on the strut, then remove it from the vehicle.
Carefully pull the strut assembly out of the vehicle
To install:
  1. Position the strut back into the vehicle with the 4 studs on the strut mount assembly through holes in the strut tower of the vehicle. Install the 4 strut mount-to-body attaching nuts onto the mount studs. Tighten the nuts to 25 ft. lbs. (34 Nm).
  2. Install the dust shield into the opening on top of the strut tower. Install the carpeting back on top of the rear strut tower.
  3. Raise and safely support the vehicle.
  4. Install the knuckle into the clevis bracket on the strut assembly. Install the 2 clevis bracket-to-knuckle attaching bolts and nuts. Hold the bolts with a wrench while tightening the nuts to 70 ft. lbs. (95 Nm).
  5. Install the brake hose bracket to the strut bracket and secure with the retaining bolts. If equipped with ABS, the wheel speed sensor cable routing clip is also attached to the strut bracket.
  6. Install the wheel and tire assembly on the vehicle. Tighten the lug nuts evenly, in sequence, to 100 ft. lbs. (135 Nm).
  7. Carefully lower the vehicle.
  8. Have the toe checked and adjusted as necessary.

Nov 05, 2009 | 1999 Dodge Neon

2 Answers

On a 1989 nissan maxima with sonar suspension II how do you disassemble the strut assembly? the mounting bracket for sonar adapters is in the way of the strut center bolt.


First you must remove the rear seat to gain access to the top strut mounts. The bottom of the rear seat comes out first. On the 91 model there are two tabs at the base of the seat bottm that you pull forward to release the seat bottom. I'm not sure if the 89 is the same. After removal of the rear seat bottom, you will see a bolt at the bottom of each side of the rear seat back that need to be removed. Fold down the arm rest and disconnect the vinyl cover at the base of the armrest to expose and remove two screws. Push up on the rear seat back to unhook three plastic hooks (center and one at each end) at the top of the rear seat back. Remove the seat back. Remove the large metal support panel that is behind the seat back. Safely jack up the rear of the car and support on jack stands so the rear wheels hang free. Doing one strut at a time, remove the two top strut mount bolts leaving the center strut stud nut in place. The strut and mount will lower out of the unibody. Disconnect the bottom strut mount. Remove the strut/coil spring assembly. Using a strut/spring compressor (some auto parts stores rent these) compress the spring. Carefully remove the top strut stud retaining nut, top strut mount, bumpers and strut boot. Carefully install compressed spring, strut boot, bumpers and top strut mount on new strut and install washer and retaining nut. Reinstall strut and etc. in reverse order.

Sep 15, 2009 | 1989 Nissan Maxima

2 Answers

Right rear wheel tilting in


You can have a balance and alignement done. Most reasons for camber is just a need of adjustment or new rear struts

Aug 24, 2009 | 2000 Jeep Cherokee

2 Answers

Insturctions for replacing rear struts


raise rear of vechicle then support by jack stands.let rear suspension hang to take pressure off strut coil springs.remove rear package tray trim panel. remove rear wheel.remove brake load sensor .remove brake hose.remove stabilizer bar bracket and link.remove tension strut .remove spindle pinch bolt and strut assembly.if the strut coil spring broke you wont need a coil springcompressor.BESURE INSTALL NEW MOUNTING BOLTS AND PINCH BOLT.install the strut assembly.use a new pinch bolt .torque it to 50-67 ft lbs.torque the 3 upper mounting nuts to 19-25 ft lbs. tension strut torque nut to 35-46 ft lbs. stabilizer bar link torque to 60- 81 inch pounds.stabilizer bar bracket torque to 25-33 ft lbs.NOW INSTALL .brake hose / brake load sensor/ rear wheel /rear package tray trim panel.

May 31, 2009 | 2000 Mercury Sable

1 Answer

How to install rear hatch door struts on a 97Astrovan


in case you havent figured it out, or for the next person that needs help. . .

i needed to replace my rear window struts.
i stuck a flathead screw driver in each of the metal clips at each end of the strut and pryed them loose. the struts popped right off the mounts. i also unscrewed the rear speaker panel so i could remove the wire connecting the strut to the car (rear defroster?) and remove completely. i wanted to take the whole unit to the autoparts store and compare it to the new strut. when buying replacements, i noticed the new struts did not come with the electrical housing on the upper end, just a male thread. i was stumped because i couldnt get the housing off of the old strut . . .i didnt want to damage it trying.

i finally i got the nerve. all it took was a pair of channel locks (pliers). grip the rod tight enough to unscrew the housing from the rod. after breaking loose, it should come right off easily.

i realized after that i didnt need to open the speaker panel and disconnect the wire. i probably could have just unhooked the strut and unscrewed the housing (while the wire remained connected to the van), screwed the new strut back into the housing, and reattached the strut to the van.

installation is the opposite of removal. i also read on a few sites that its a good idea to replace them both at the same time.

May 21, 2008 | 1997 Chevrolet Astro

Not finding what you are looking for?
1995 Dodge Neon Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...