Question about 2001 Ford Escape

Open Question

How do I change my 01 ford escape turning light(front)

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 321 Answers

SOURCE: front wheel bearing 2004 escape 4x4

It's nearly impossible unless you have a good air compressor and a powerful 1/2" or larger drive impact gun.The reason is you have to remove the cv axle nut and axle out of the way before removing the bearing and hub.The axle nut requires a couple hundred foot pounds to remove.The procedure is:Jack vehicle safely off the ground,remove wheel and tire.Remove axle retaining nut.Remove balljoint nut and bolt,pry down on lower control arm,and disengage balljoint and lower arm from spindle.Now the axle can be released from the hub,but leave the other end of the axle in the trans,just set off to the side out of the way.At this point,there are two ways to change the bearing.The wheel bearing is a double roller,cartridge type with the hub containg the wheel studs,pressed into the bearing.Remove the entire spindle assembly from the suspension strut,OR leave the spindle attached to the strut,and remove the bearing and hub from the spindle.Some guys swear by taking the spindle to a press,and pressing the bearing assembly out with a bottle jack.I just use a bushing driver set,and ball peen hammer,and remove the hub from the bearing...then remove the snap ring retaing the bearing in the spindle,then drive the bearing out of the spindle with the hammer and drivers.There you have it.Reverse procedure for reassembly

Posted on Jul 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace 2006 ford escape left front axle shaft


How to Replace a CV Axle on a Ford Escape / Mazda ...

? 9:41
https://www.youtube.com/watch?v=_JxagNLBlQ4
Aug 29, 2013 - Uploaded by klowny1969
Axle nut should be torqued to spec..in the ford escape its around 205-220 lbs ft How To Change An Axle On A Front Wheel Drive Car ! SUBSCRIBE ! ... How to Replace a Front Axle Half Shaft - Duration: 14:37. ... Alternator replacement 2005 2006 Ford Escape 3.0L DOHC All Wheel Drive - Duration: 13:15.

Front axle replacement Ford Escape 2003 Right front CV ...

? 8:46
https://www.youtube.com/watch?v=JQK8SPj6Qsk
Mar 29, 2014 - Uploaded by Fixing cars and stuff
Front axle replacement Ford Escape 2003 Right front CV axle install remove replace This Channel provides ...

Feb 03, 2016 | Ford Cars & Trucks

1 Answer

Frequently will not shift out of park - I usually have to turn the engine off several times and suddenly it will go into gear - what is going on?


Ford Escape Questions - shifter stuck in park - CarGurus

www.cargurus.com > Questions > Ford > Escape

CarGurusFeb 2, 2015 - shifter stuck in park - Sometimes my shifter is hard to get out of park. what would cause this, and how would I fix it?

Ford Escape Questions - SHIFTER - CarGurus

www.cargurus.com > Questions > Ford > Escape

CarGurusOct 28, 2011 - 1 out of 1 people think this is helpful. ... 2011 FORD ESCAPE WILL NOT GO IN TO GEAR DEALER SAID COFFE SPILLED IN IT . ... shifter stuck in park 13 answers ... Other times (and it's getting more often), I have to push and push (and keep pushing) the gear shifter ... 2012 Ford Escape XLT For Sale.

'01 Escape Stuck in Park; safety interlock - Ford Truck ...

www.ford-trucks.com > ... > Escape & Escape Hybrid

Dec 29, 2015 | 2012 Ford Escape

1 Answer

When I open the front door on my 2008 Ford Escape the back dome light comes on, but not the front one. I can turn the front one on with the switch and it comes on.


Move the switch to the position that the light comes on with the door. It should be a 3 position switch with on, off, and door to choose from.

Dec 17, 2015 | 2008 Ford Escape

1 Answer

No tail lights on my 2008 ford escape. driver rear blinker wasn't working. replaced bulb, but when i turn on the blinker both blinkers are blinking...front and back...


Not sure I follow your story.
The front and rear turn signal should blink on one side. If the tail lamps are not working, it could be a fuse or a problem with the wiring. And the tail lamps are on the same circuit as the front parking lamps.

Feb 26, 2014 | 2008 Ford Escape

1 Answer

Turn off change oil light in a 2009 Ford Escape Hybrid


PLEASE TELL ME ABOUT MANUAL PROCEDURE OF RESET OF THE MEMORY OF THE FORD ESCAPE HYBRIDE 2006 AFTER REVISION

May 10, 2010 | 2007 Ford Escape Hybrid FWD

1 Answer

HOW DO YOU REMOVE THE HEADLIGHT ASSY TO REPLACE THE TURN SIGNAL BULB


SECTION 417-01: Exterior Lighting 2001 Escape Workshop Manual REMOVAL AND INSTALLATION Side Lamp/Front Turn Signal Lamp Bulb Removal and Installation
  1. Remove the wheel and tire. For additional information, refer to Section 204-04 .
  1. Position the inner fender well aside.
    1. Remove the bolts.
    1. Remove the pin-type retainers.
    1. Remove the screw.
    1. Position the inner fender well aside.
  2. Remove the lamp socket from the lamp assembly.
  3. Remove the bulb.

06a0ca1.gif

Dec 01, 2009 | 2001 Ford Escape

2 Answers

Battery light turns on and off


its a bad alternator should be at 14.5 or pretty close to that i have purchased new parts that were faulty as well

Aug 05, 2009 | 2003 Ford Escape

1 Answer

2006 Ford Escape - Right side flashers (turnsignals) not working


Check the wires at the connection point and follow them back up to the tail light look for any disconnected wires or grounds. Good luck.

May 14, 2009 | 2006 Ford Escape

1 Answer

Replace ford escape turn signal front 2005


you should not have t remove the headlight assembly to replace the bulb access should be under the hood. as for the moisture the bulb holder may be damaged or not fitted properly

Oct 16, 2008 | 2005 Ford Escape

Not finding what you are looking for?
2001 Ford Escape Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...