Question about 2005 Ford Focus

1 Answer

Broken rear wheel stud on a 2005 ford focus zx4 se

Broken rear wheel stud

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 691 Answers

  1. Step 1 Buy a new stud. Make sure you purchase the right size. If you're not sure what size to get, wait until you remove the stud and take it with you to the store.
  2. Step 2 Check the area of the spare tire in the trunk for the jack and the jack tools since you'll need to raise the car to replace the wheel stud on your Focus. Be sure to block the tire diagonal to the jack.
  3. Step 3 Use the jack to raise the Focus. Remove the wheel Take off the caliper and either hang it by a mechanics wire or lay it up so it doesn't dangle by the brake line. Remove the rotor. If you're working on back wheels, you have to remove the emergency brake clip first. You could have drum brakes in the rear. If they're drum brakes, remove the drum.
  4. Step 4 Hunt for an opening behind the hub that allows you to remove the stud. Line the stud up with the hole. You may have to take off the hub and put it in a vise if you can't drive it out the back.
  5. Step 5 Hit the stud with a mallet and drive it out the back of the hub. Push another stud into the opening. This is tough work, but you only need to push it far enough to thread on a wheel bolt.
  6. Step 6 Put on a wheel bolt and begin to tighten it. As you do, the stud starts to pull through. Add more bolts as necessary until you seat the stud. Check in the back of the hub. When the head is flush with the stud, you seated it.
  7. Step 7 Remove the extra bolts and reassemble the parts that you took off to replace the wheel stud on the Ford Focus. Put the wheel back on the vehicle and tighten down the wheel nuts.

Posted on Sep 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I got a zx4 2005 ford focus that will not engage when I put it in to gear. What can I do?


broken cable. try operating the gearshift while looking for the operation on the transmission itself. raise hood and observe the transmission.

Apr 16, 2015 | 2005 Ford Focus ZX4

1 Answer

2005 SE ZX4 ford focus


It's a problem inside the transmission. Could be as easy as a fluid and filter change. Could be the solenoid package.

Aug 30, 2014 | 2005 Ford Focus

1 Answer

What parts do i need to repair the front door handle on my 2005 ford focus zx4. handle still there but doesnt open


there is a skinny rod that hooks up to the handle the little washer looking piece holds it in place it might have fallen off

Feb 28, 2013 | 2006 Ford Focus

1 Answer

Diagram for heater control box for ford focus 2005 zx4 se


what do you need ? the one going to the blower motor or blower resister or the blend door motor

Jan 06, 2013 | Ford Focus Cars & Trucks

1 Answer

Whre are airbag sensors located on 2005 ford focus zx4-se


in the front of the car , look for a connector that has a blue and orange connector,, follow those wires to the sensor,, if you google Focus air bag problems, you will see that Ford has lots of problems concerning this make, and might be under recall

Jul 31, 2011 | Ford Focus Cars & Trucks

1 Answer

Need to know if my 2005 ford focus zx4 se is a timming belt or chain?


Timing belt, good for 100,000 miles before replaicng. They go to 150,000 easy and it is a freewheeling engine, no dmamge to valves or pistion if it breaks

Gerry from Ford.

Apr 22, 2011 | 2005 Ford Focus

1 Answer

I need to remove and replace the alternator on my 2005 ford focus zx4. what is he bet way to do this?


easy ,slacken the belt tensioner ,then them star headed bolts out ,then remove the long stud and away you go ten minute job

Sep 03, 2010 | 2005 Ford Focus

1 Answer

How can i add freon to my cars' air conditioner for a ford focus zx4 se?


Charging the System

  1. Lubricate the refrigerant system with the correct amount of clean PAG oil.
  2. Connect an R-134a A/C service center to the low-side and high-side service gauge port valves following the operating instructions provided by the equipment manufacturer.
  3. Set the refrigerant charge amount, and charge the refrigerant system following the instructions provided by the equipment manufacturer.

May 23, 2010 | 2005 Ford Focus

1 Answer

What type of antifreeze is used with a 2005 Ford Focus


Hello mk12x.

Ford specification is Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A (green color) with a mix of 50-50 coolant and clean water.
I hope your repair goes well for you.

Kl

Dec 17, 2009 | 2005 Ford Focus

1 Answer

Right side mirror.


Pull the door panel off, the studs are behind it.

Oct 28, 2008 | 2006 Ford Focus

Not finding what you are looking for?
2005 Ford Focus Logo

755 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...