Question about 2001 Hyundai Accent

1 Answer

Hyundai was stuck in sand & i hooked onto a part beneath left rear wheel & now rear wheel is off alignment.

Posted by on

  • bulldogchief
    bulldogchief May 11, 2010

    well, unless you have an alignment machine in your garage, you need to take your car to a shop to get it aligned.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 366 Answers

U problably bent the lateral bar when towing it out,check for what is damage and replace,have it realign or take it to alignment shop for repair.

Posted on Sep 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the red and yellow wires for?


Hey Bob, how's it going ? The two big ones there with the 125 amp fuse or breaker , they go to the rear fuse block ,that's power supply ! power supply for trailer hook-up comes from rear fuse box. The other wire supply's the body control module ! 42 TR PARK Fuse 10A Trailer Connector .
Fuse Block - Rear
Beneath the left rear seat

Feb 27, 2015 | 2005 Chevrolet TrailBlazer

1 Answer

Front Wheel Allignment


On these LH body cars, camber is not adjustable. Neither is caster. Those angles are preset by the suspension geometry. However, specifications for them ARE published. Generally, if either of those two parameters are out of spec, then it's likely something is worn or damaged and needs to be replaced.

The only adjustable parameters are to the front and rear toe but specified as "Total Toe" - see note below.
The alignment specs are as follows ...

ALIGNMENT SPECIFICATIONS AT VEHICLE CURB HEIGHT
A. FRONT WHEELS
  1. CAMBER
    Acceptable -0.6° to +0.6°
    Preferred +0.0°
    Side to Side Differential
    Acceptable 0.7° or less
    Preferred 0.0°
  2. TOTAL TOE - Specified in degrees. See Note Below
    Acceptable 0.4° in -to- 0.0° out
    Preferred 0.2° in
  3. CASTER* (reference angle)
    Acceptable +2.0° -to- +4.0°
    Preferred +3.0°
    *Side to Side Caster Difference not to exceed
    Acceptable 1.0° or less
    Preferred 0.0°
B. REAR WHEELS
  1. CAMBER
    Acceptable -0.6° -to- +0.4°
    Preferred +0.1°
  2. TOTAL TOE** - Specified in degrees. See Note Below.
    Acceptable 0.2° out -to- 0.4° in
    Preferred -0.1° in
    **TOE OUT when backed onto alignment rack is TOE IN when driving.
  3. THRUST ANGLE
    Acceptable -0.15° -to- +0.15°
Note: "Total Toe" is the arithmetic sum of the left and right Toe settings. Positive is Toe-in. Negative is Toe-out. Total Toe must be equally split between left and right wheels. Left and Right Toe must be equal to within 0.02° (2 one hundredths of a degree).

Courtesy RJK & Concorde Shop Manual

Mar 08, 2014 | 1994 Chrysler Concorde

1 Answer

Car feels crooked


When you said you had several alignments, where they just front wheel alignments, or all four wheel alignments?

Sometimes, the rear can get out of alignment, also.

Jan 21, 2014 | 2009 Hyundai Accent

1 Answer

Rear wheel alignment


rear wheel alignment should always be done before a front end alignment as it affects the front end settings. Get onto a good wheel aligner and tell him that you want the rear end aligned first as most ignore that bit as it takes time and you are being charged for it but it is profit if they skip it because you do not know about it or do not insist on it.

Oct 31, 2013 | Cars & Trucks

2 Answers

How do you know if you need a 4wheel or 2wheel alignment? 2000 Mercury Cougar.


Most FWD vehicles can have a four wheel alignment performed. A 2 wheel alignment is mainly for vehicles that are rear wheel drive. There are exceptions but the 2000 Mercury Cougar is a 4 wheel alignment.

Apr 19, 2011 | 2000 Mercury Cougar

1 Answer

I would like to know what would make my rear wheels to go bald?


here are the reasons, rear wheel alignmemt is way off, (yes the rear is aligned on modern cars) tires are not inflated to spec, worn rear suspension parts, alignment is the most common reason

Sep 17, 2009 | 2001 Hyundai XG300

1 Answer

What are the front toe in parameters for Hyundai Tucson?


Wheel & Tire
Wheel alignment
Front
Rear
Dimension
Toe-in
Camber
Caster angle(to ground))
King pin angle
King pin offset mm(in.)
Side slip mm(in.)
P215/65R16
0°±0.2°
0°±0.5°
3.53°±0.5°
12.77°±0.5°
-9.73(0.383)
±3(0.118)
P235/60R16
0°±0.2°
0°±0.5°
3.53°±0.5°
12.77°´±0.5°
-10.41(0.410)
±3(0.118)
P215/65R16
0.37° ~ 0.41°
-0.92°±0.5°



±3
P235/60R16
0.37° ~ 0.41°
-0.92°±0.5°



±3
Wheel
Size
Run out mm(in.)
AL wheel
6.5JX16
Radial : 0.3(0.01), Lateral : 0.3(0.01)
Tire
Size
Inflation pressure kg/cm² (psi)
P215/65R16, P235/60R16
2.1±0.07(30+1.0)

Apr 30, 2009 | Hyundai Tucson Cars & Trucks

1 Answer

The car is darting to the left and right.


Check wheel alignment and suspension system components. You'll need to seek a professional in alignment procedures for this one and the equipment necessary to complete it. Hyundai Service Centers are equipped with all the special tools/equipment to do this. It could simply be negative (-) front toe, or a combination of Camber and Caster measurements (cross Camber) adjustments. Hyundai Parts department stocks (or can order) Camber kits & Service can install them if this is where the problem is.

Dec 06, 2008 | 2004 Hyundai Tiburon

1 Answer

Left rear wheel


Sounds like an alignment issue. I suggest taking it to a alignment shop for further diagnoses.

Sep 12, 2008 | 2004 Hyundai Elantra

Not finding what you are looking for?
2001 Hyundai Accent Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...