Question about 1999 Volvo V70

Open Question

Where can I get a diagram to replace the front strut mount and upstream Oxygen sensor?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is location of bank 1/sensor 1 oxygen sensor v6 ?


Bank 1 means the side of engine which has #1 cylinder in it, which is the left or driver's side of the engine. Sensor 1 means it is the one closest to the exhaust manifold or before the catalytic converter, better known as "upstream" oxygen sensor. On the 4.3 V6 I believe this sensor is mounted in the exhaust manifold itself. You maybe able to access it from underneath the vehicle, or you may have to remove the "doghouse" interior engine access hood. The oxygen sensor has an electrical connector on it that has to be disconnected and the you may need a specialty socket called an oxygen sensor socket. the size of the hex on the oxygen sensor is 7/8".

Apr 27, 2014 | 2003 Chevrolet Astro

1 Answer

Code p0420 acura m'dx


1996-newer (OBD-II) vehicles use oxygen sensors and a catalytic converter to reduce emissions. There is one O2 (oxygen) sensor in front of the catalytic converter (called upstream), and one behind it (downstream). When the engine is warmed up and running normally the upstream oxygen sensor reading fluctuates and the downstream one is fairly steady. In the case where both readings are fairly steady, a P0420 check engine light code is set.
Possible Causes: Oxygen (O2) sensor not working correctly
Damaged or leaking exhuast (pipe, manifold, catalytic converter)
Damaged catalytic converter
Diagnostic Help:
To diagnose a P0420 trouble code we begin by checking for exhaust leaks under the vehicle. Then use an oscilliscope to check the waveforms of both upstream and downstream O2 sensors. The front reading should vary, the rear should be steady. Replace as necessary. Check the rear Heated O2 Sensor. Check the catalytic converter, replace if necessary. If necessary, check for wiring and component concerns. See our article "Automotive Circuit Testing 101", if you need more assistance with this. Remember to refer to an model-specific repair manual for proper instruction.

Jan 20, 2014 | 2005 Acura MDX

1 Answer

What is the best way to remove O2 sensor bank 1 sensor 2?


Here is the low-down on oxygen sensors, and their location designations explained:

Oxygen sensors are screwed into the exhaust system at various points. Some people say that there are 4 oxygen sensors, but technically, that is not correct. Only the front 2 are considered oxygen sensors.

These oxygen sensors are screwed into the exhaust pipe or directly into the exhaust manifold, one on each bank. Because they are in front of the catalytic converter, this is often referred to as 'upstream'.

The other 2 are actually called catalyst monitors. They are oxygen sensors, but they serve a different purpose. They monitor the activities of the catalytic converters, thus the name, catalyst monitors. They are screwed into the exhaust one on each bank, after, or downstream, of the catalytic converters.

On a 4 cyl engine, there are only a total of two such sensors, the one in front of the catalytic converter is the O2 sensor, the one behind the cat is the catalyst monitor.

The location names for them are as follows:
  • On a 4 cyl, the front / upstream is called "bank 1 sensor 1" and the rear / downstream sensor is called "bank 1, sensor 2."

  • On a V6 or V8 engine:

    • the passenger side bank on a forward facing engine, or the bank closest to the firewall on a transverse mounted engine, is bank number 1, so the forward / upstream sensor on that bank would be "bank 1, sensor 1."

    • The driver's side bank (forward facing mount engine), or front bank (transverse engine) would be bank number 2, thus the forward / upstream sensor on that bank would be "bank 2, sensor 1," and the rearmost / downstream sensor on that bank would be "bank 2, sensor 2."

Jul 28, 2012 | 2004 Mitsubishi Endeavor

1 Answer

How any oxygen sensors are on a 1999 grand cherokee laredo 4.0 & were is it/they located?


On Grand Cherokee oxygen sensor locations for 4.0 and 4.7 engines, check this diagrams...


12_18_2011_2_25_33_pm.jpg


12_18_2011_2_26_23_pm.jpg

The Oxygen Sensors (O2S) are attached to, and protrude into the vehicle exhaust system. Depending on the emission package, the vehicle may use a total of either 2 or 4 sensors.

Federal Emissions Package (4.0L and 4.7L engines):
Two sensors are used: upstream (referred to as 1/1) and downstream (referred to as 1/2). With this emission package, the upstream sensor (1/1) is located just before the main catalytic convertor. The downstream sensor (1/2) is located just after the main catalytic convertor.


California Emissions Package (4.0L engine):
On this emissions package, 4 sensors are used: 2 upstream (referred to as 1/1 and 2/1) and 2 downstream (referred to as 1/2 and 2/2). With this emission package, the rear/upper upstream sensor (2/1) is located in the exhaust downpipe just before the rear mini-catalytic convertor. The front/upper upstream sensor (1/1) is located in the exhaust downpipe just before the front mini-catalytic convertor. The rear/lower downstream sensor (2/2) is located in the exhaust downpipe just after the rear mini-catalytic convertor, and before the main catalytic convertor. The front/lower downstream sensor (1/2) is located in the exhaust downpipe just after the front mini-catalytic convertor, and before the main catalytic convertor.


California Emissions Package (4.7L engine):
On this emissions package, 4 sensors are used: 2 upstream (referred to as 1/1 and 2/1) and 2 downstream (referred to as 1/2 and 2/2). With this emission package, the right upstream sensor (2/1) is located in the right exhaust downpipe just before the mini-catalytic convertor. The left upstream sensor (1/1) is located in the left exhaust downpipe just before the mini-catalytic convertor. The right downstream sensor (2/2) is located in the right exhaust downpipe just after the mini-catalytic convertor, and before the main catalytic convertor. The left downstream sensor (1/2) is located in the left exhaust downpipe just after the mini-catalytic convertor, and before the main catalytic convertor.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Dec 13, 2011 | 1999 Jeep Grand Cherokee

1 Answer

How many oxygen sensor on a 02 chevy blazer


Hi, there are 4 sensors on your truck--two upstream and 2 downstream. The upstream sensors are mounted in the exhaust manifolds and the downstream sensors are mounted just behind the catalytic converters. The upstream and downstream sensors are different. Bank 1 is on the driver's side and bank 2 is on the passenger's side. Please let me know if you have more questions, and thanks for using FixYa.

jturcotte_682.gif
jturcotte_683.gif

Jan 01, 2011 | 2002 Chevrolet Blazer

1 Answer

Have a oxygen sencor and dont know were to put it in at thanks....


WELL WHICH OXYGEN YOU REPLACING THE UPSTREAM OXYGEN SENSOR MOUNTED IN EXHAUST MANIFOLD AND THE DOWN STREAM OXYGEN SENSOR LOCATED IN THE EXHAUST SYSTEM AFTER THE CATALYTIC CONVERTER .YOU NEED A OXYGEN SENSOR SOCKET TO REMOVE IT.TO REMOVE OXYGEN SENSOR CRANK VECHICLE TO GET OXYGEN SENSOR HOT BECAUSE HARD TO REMOVE WHEN COLD.BECAREFUL DONT GET BURN ON EXHAUST MANIFOLD WHEN REMOVING OXYGEN SENSOR.AND WHEN INSTALLING NEW OXYGEN SENSOR USE ANTI SEIZE COMPOUND ON SENSOR THREADS.BUT MOST OF THE TIME NEW SENSOR WILL HAVE ANTI SEIZE COMPOUND ON IT.

Dec 08, 2010 | 2002 Jaguar S-Type

1 Answer

What does po135, p1131, and p0305 mean on a ford f250 with a 4.6L 2007


PO135 = Upstream Heated Oxygen Sensor Heater (HTR 11) circuit (Bank #1)

P1131 = Lack of upstream Heated Oxygen Sensor (HO2S 11) switch, sensor indicates lean (Bank #1)

P0305 = Cylinder #5 Misfire detected

It looks like you have two separate issues happening. Bank 1 would be the left side of the engine if you were standing in front of the truck looking at the engine. The "upstream" oxygen sensor will be on the exhaust pipe coming from the bank one side of the truck IN FRONT of the catalytic converter. From the codes, it appears that the upstream sensor has gone bad, but the oxygen sensor behind the catalytic converter, or "down stream" is fine.

The misfire on cylinder 5 on the right side of the engine, 2nd one from the front, could be something as simple as a fouled spark plug or a coil malfunction.

To identify if it is a bad coil, swap the #5 cylinder coil with another coil, and see if the misfire follows the relocated coil.

Dec 22, 2009 | 2007 Ford F-250 Super Duty Lariat

3 Answers

Location of upstream and down stream oxygen sensors on 3.8 buick lesabre


They are usually on your exhaust pipe before and after the catalitic converter.

Nov 07, 2009 | 2000 Buick LeSabre

1 Answer

Replace oxygen sensors


these engines have 1 upstream o2 sensor and 1 downstream o2 sensor..the 1 in the rear exhaust manifold is the upstream and the 1 after the converter is the downstream..make sure you replaced the right one

May 15, 2009 | 1998 Plymouth Grand Voyager

2 Answers

EMISSION FAIL CODES PRESENT P0155


P0155 - Heated Oxygen Sensor Heater Circuit (bank 2, sensor 1)

bank 2 sensor 1 (front, driver side) o2 sensor needs to be replaced

Oct 15, 2008 | Mitsubishi Montero Cars & Trucks

Not finding what you are looking for?
1999 Volvo V70 Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...