Question about 1995 Ford Escort

1 Answer

Traveling at an estimated speed of 70 mph, car lost acceleration. Slowed to a stop. Ignition turns over, battery initiates, no 'fire' to engine. Fuel pump not the problem...

Posted by on

  • trishlynnins Sep 25, 2009

    95 ford escort does not have distributor...

  • trishlynnins Sep 25, 2009

    Timing belt snapped. Lucky engine didn't blow. looking for online diagram of external engine,specifically belts, 1.9 engine. Any suggestions?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,187 Answers

No fire? There probably is fire, but out of time or some liquid (water, oil, PS fluid, etc.) got into the distributor cap and the rotor fire is shorting (sparking) to ground through the liquid.
Check spark anyway, pull a plug cable and set down on metal part of engine ground. Ahve someone crank starter while you look for spark from end of sparkplug cable to ground.
Let us know...

Posted on Sep 25, 2009

Testimonial: "Slowly but surely we're getting there! Thanks for the suggestions. The first comment about timing pointed us the right way. Overlooked that at first."

  • Just Gort
    Just Gort Sep 25, 2009

    Unless the engine was changed, all 1995 Ford Escorts with 4-cyl (1.8L) engines have a "Mitsubishi" distributor.

    -- or -- after-market electronic ignition was installed.

    What motor is in that Ford Escort?

  • Just Gort
    Just Gort Sep 25, 2009

    I will locate the diagram online, none in my library.

    Go to a public library (you have a card, right?)

    Go to the "Reference Section" and locate your vehicle in one of the auto repair books (Chilton's, Motor, etc.)... photocopy the necessary pages (10 ~ 25 cents per page) on the public copy machines.



    I will post link when I find a diagram.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

04 saturn L300


Next time the engine light comes on, get the codes pulled and get back to me

Apr 15, 2013 | Cars & Trucks

1 Answer

04 saturn L300 acceleration dies


run the fault codes first to check for faulty sensors
what you describe indicates a problem in the exhaust in that when the exhaust gas volume reaches a certain level the sensors are reporting it and the ECM is not able to fix it
have an accredited exhaust shop check the cat converter
for failure and partially blocking the exhaust at speed
if it was a fuel pump you would run into problems long before the speed at which it occurs
AT best it could be an EVAP problem with the vent not working properly but I think that it is exhaust related

Apr 30, 2017 | 2004 Saturn L-Series

1 Answer

Vapor lock


Ask your local technician to set up a fuel gauge pressure monitor so you can track it while your driving. Ask him what the normal range is so you will know when it falls below. Document it and let your Tech know. It sounds like your fuel pump is loosing Pressure.

Sep 15, 2012 | 1999 Subaru Forester

1 Answer

NEED DRIVE CYCLE FOR 2004 CRV TO RESET CAT AND O2 MONOTOR


Here is the info

NOTE: The ignition key must not be on prior to the cold start otherwise the heated oxygen sensor diagnostic may not run.

1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear defrost on. OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.

2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. OBDII checks for ignition misfire, fuel trim and canister purge.

3. Hold at a steady state speed of 55 mph for three minutes.

OBDII monitors EGR, air pump, O2 sensors and canister purge.

4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. OBDII checks EGR and purge functions.

5. Accelerate back to 55 to 60 mph at half throttle. OBDII checks misfire, fuel trim and purge again.

6. Hold at a steady speed of 55 to 60 mph for five minutes.

OBDII monitors catalytic converter efficiency, misfire, EGR, fuel trim, oxygen sensors and purge functions.

7. Decelerate (coast down) to a stop without braking. OBDII makes a final check of EGR and canister purge.

Oct 02, 2010 | 2004 Honda CR-V

1 Answer

Obd2 system rediness status won't clear so I can run the smog test due to replacing the battery.


takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

Sep 15, 2010 | 1998 Mitsubishi Eclipse

1 Answer

We are experiencing an intermittent loss of power on our 2005 Ford F250 super duty 4x4 6.0 liter diesel truck (45k miles on it). Description: While towing a boat, the truck loses power. When climbing...


This engine is fully electronically controlled, so you need the dealer to do a full diagnostic of the engine control system, it is the only way to get to the bottom of this. Make sure you can show the dealer exactly what is going on otherwise if they can't duplicate the concern and no fault codes are present they can't fix it.

Mar 16, 2017 | 2005 Ford F 250 Super Duty

2 Answers

Reset computer in doege stratus wont pass inspection drove 50 miles and computer still didnt reset help


U have to operate the engine at all kinds of diff speeds and drive modes, it is called a OBDII drive cycle, here is how u do one.
1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear defrost on. OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.

2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. OBDII checks for ignition misfire, fuel2_bing.gif trim and canister purge.

3. Hold at a steady state speed of 55 mph for three minutes.

OBDII monitors EGR, air pump, O2 sensors and canister purge.

4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. OBDII checks EGR and purge functions.

5. Accelerate back to 55 to 60 mph at half throttle. OBDII checks misfire, fuel trim and purge again.

6. Hold at a steady speed of 55 to 60 mph for five minutes.

OBDII monitors catalytic converter efficiency, misfire, EGR, fuel trim, oxygen sensors and purge functions.

7. Decelerate (coast down) to a stop without braking. OBDII makes a final check of EGR and canister purge

Jun 02, 2010 | 2004 Dodge Stratus

Not finding what you are looking for?
1995 Ford Escort Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...