Question about 1998 Jeep Cherokee

1 Answer

How do i locate a crank sensor and the code comes up as po320. thank you

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 677 Answers

Yes the po320 code is no signal at the crank.It is located on the transmission bellhousing.Its on the lefthand side of the housing in the top quarter.At the back of the motor.After the problem has been fixed,do not disconnect the battery to clear the code.Get the codes cleared before starting the motor or the comp may set a trouble code for that.A scan tool is needed from a dealer or good shop.I hope this helps

Posted on Sep 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What will fix codes po320 & po446?


EOBD code Fault location Probable cause
P0320 Crankshaft position WiringCKP/RPM ,
(CKP) sensor/engine sensorECM
speed (RPM) sensor
circuit malfunction
,
EOBD code Fault location Probable cause P0446 Evaporative emission (EVAP) system, vent control - circuit malfunction Wiring, EVAP canister purge valve, ECM Hope that helps

Oct 19, 2014 | 2007 Ford Explorer Sport Trac

1 Answer

What is the fix for code po320 in a 1996 ford f150 4.6L


P0320 is for CKP crank shaft position sensor. CKP is the first sensor to wake up and tells all others to wake up. Without it no run. Change sensor and reset computer

Nov 20, 2013 | Cars & Trucks

1 Answer

Could po320 be drive shaft speed sensor


code p 0320 refers to crankshaft position (CKP) sensor /engine speed (RPM) sensor---circuit malfunction====causes --wiring--CKP/RPM sensor ---ECM check the wiring to the crank position sensor
replace the crankshaft position sensor

Apr 16, 2017 | 2004 Jeep Grand Cherokee

1 Answer

What does code PO320


According to my code manual PO 320 code means ,There is no signal to the crank shaft position (Sensor)

Nov 10, 2012 | 1998 Jeep Cherokee

1 Answer

Diagnostic code p0320


po320 is either the coil pack, the crank sensor or the cam sensor. po320 means--
Ignition Engine Speed Input Circuit Malfunction

Apr 22, 2012 | 1997 Mercury Cougar XR7

1 Answer

2003 Hyundai Santa Fe Still Will Not Start PO320 PO340


code p 0320 refers to crank shaft position sensor (CKP)/engine speed (RPM ) sensor---circuit malfunction====causes ---wiring---CKP/RPM sensor ---ECM
code p 0340 refers to camshaft position sensor (CMP) sensor A bank 1---circuit malfunction===causes wiring---CMP sensor ---ECM
following engine work , it is always best to check that all of the harness connections were assemble properly
check for broken wires during the work

Apr 29, 2017 | 2003 Hyundai Santa Fe

1 Answer

96 jeep cherokee 4.0 has no spark po320 shows could the cam sensor cause it to have no spark


Cam sensor, crank sensor, bad coil, all could give no spark. Check all fuses and relays.... wiring connections as well. 320 is a crank sensor code.

Aug 25, 2010 | 1996 Jeep Grand Cherokee

1 Answer

Our Jeep liberty Po320 code than misfire replaced parts and same codes again than stalls after it get warm. Could this be a PCM units


disconnecting the battery will only temporarily erase your code or check engine light. put your keys in the ignition, then turn it in the on position. Do not turn it so that the engine turns over, but as if you were just turning the radio on. Keep it on for 2 to 4 seconds repeat 40 times. i no it may take a while but unless you have a scanner its the only way.

Jan 16, 2010 | 2002 Jeep Liberty

2 Answers

Po320 code and code po303 2004 lincoln navigator


Replaced a camshaft sensor still running rough & engine light still on, 2004 lincoln nav. 5.4 liter

Jan 02, 2010 | 2004 Lincoln Navigator

Not finding what you are looking for?
1998 Jeep Cherokee Logo

Related Topics:

422 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...