Question about 1996 GMC Jimmy

1 Answer

Ball joints the lower ball joints say tighten to 15 ft.lbs for mounting bolts and nuts, the alldata info says tighten to 17ft.lbs, the bolt torque charts on line, say these type of bolts should be torqued from 12-14ft.lbs. would 15 or 17 break the bolts or be to tight......would my upper ball joint mounting hardware be torqued the same as the lowers

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

Alldata is usually the correct source of information tho recheck that it is showing ft lbs.
best way to find out exactly what it should be is to call your local dealer, ask for the parts guy and see if he will look up the correct torque for those bolts.

robert

Posted on Sep 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for ball joints on 2000 gmc jimmy


Upper ball joint knuckle nut 60 ft lbs, lower ball joint knuckle nut 80 ft lbs....mounting nuts and bolts 17 ft lbs

Jul 12, 2014 | 1996 GMC Jimmy

1 Answer

Control arm replace


to replace control arm, you need place jackstands under the frame and lower vechicle so the weight of the vechicle rests on the jackstands and not on the control arms, then remove the front wheel remove ball joint and nut, remove steering knuckle from the lower ball joint using tool KM 507 B. remove control arm to crossmember nut and bolt, remove rear crossmember to body bolt and remove control arm.torque control arm to crossmember nut and bolt 81 ft lbs, torque ball joint to steering knuckle bolt nut 44 ft lbs.torque crossmember to body bolt to 145 ft lbs.

Feb 15, 2012 | 2001 Daewoo Nubira

1 Answer

Torque on front ball joints 2000 Honda Passport 2 wheel drive


Lower ball joint specs:
Torque the ball joint-to-control arm nuts/bolts to 85 ft. lbs. (115 Nm). Torque the castellated nut to 108 ft. lbs. (147 Nm).

Upper ball joint specs:
Tighten the mounting bolts to 42 ft. lbs. (57 Nm) and the castellated nut to 72 ft. lbs. (96 Nm).

Feb 28, 2011 | 2000 Honda Passport

1 Answer

Replace lower ball joints. How do you replace Lower ball jonits?


REMOVAL & INSTALLATION
  1. Raise and safely support the vehicle, allowing the front suspension to hang free.
  2. Remove the wheel and tire assembly. WARNING
    Be careful when working in the area of the CV-joint boot. Damage to the boot could result in eventual CV-joint failure. If necessary, install CV-joint boot protector tool J-34754 or equivalent, to protect the boot.
  3. On Eldorado and Seville with 4.6L engine, remove the road sensing suspension position sensor from the lower control arm.
  4. Remove the cotter pin and nut from the ball joint stud. Use ball joint separator tool J-36226 or equivalent, on Deville and Fleetwood or ball joint separator tool J-35315 or equivalent, on Eldorado and Seville, to separate the ball joint from the steering knuckle.
  5. On Deville and Fleetwood, loosen the stabilizer bar link nut.
    1. Drill out the 3 rivets retaining the ball joint to the lower control arm and remove the ball joint. NOTE: Recommended drill-bit is 1⁄2 inch (13 mm). Fig. 1: Drilling the rivets out of the lower control arm 91048g05.gif
      Fig. 2: Installing the bolts in the lower control arm 91048g06.gif
      To install:
  6. Attach the new ball joint to the lower control arm with 3 mounting bolts and nuts.
    1. On Deville and Fleetwood, the bolts must be installed from the top of the control arm.
    2. On Eldorado and Seville, the bolts must be installed from the bottom of the control arm
    3. Tighten the nuts to 50 ft. lbs. (68 Nm).
    4. On Catera, the bolts must be installed from the top of the control arm.
    5. Tighten the nuts to 26 ft. lbs. (35 Nm).
  7. On Deville and Fleetwood, tighten the stabilizer bar link nut to 13 ft. lbs. (17 Nm).
  8. Connect the ball joint to the steering knuckle and install the castellated nut.
  9. On Deville and Fleetwood, tighten the ball joint nut to 88 inch lbs. (10 Nm). Then tighten the nut an additional 120°, during which a tighten of 41 ft. lbs. (55 Nm) must be obtained.
  10. On Eldorado and Seville, tighten the ball joint nut to 84 inch lbs. (10 Nm). Then tighten the nut an additional 120°, during which a minimum torque of 37 ft. lbs. (50 Nm) must be obtained. If the minimum torque is not obtained, check for stripped threads. If the threads are okay, replace the ball joint and knuckle.
  11. On Catera, tighten the pinch bolt to 74 ft. lb. (100 Nm).
  12. Install a new cotter pin. If the cotter pin cannot be installed because the hole in the stud does not align with a nut castellation, tighten the nut up to an additional 60°to allow for installation. NEVER loosen the nut to provide for cotter pin installation.
  13. On Eldorado and Seville with 4.6L engine, install the road sensing suspension position sensor to the lower control arm.
  14. If necessary, remove the CV-joint boot protector tool.
  15. Install the wheel and tire assembly and lower the vehicle. Fig. 3: Separating the ball joint from the steering knuckle 84208016.gif
    Fig. 4: Lower ball joint installation - Deville and Fleetwood 84208017.gif
    Fig. 5: Lower ball joint installation - Eldorado and Seville 84208018.gif

Jan 17, 2011 | 1991 Cadillac DeVille

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

I'm in the process of replacing the front struts on my wife's 2000 Lexus ES300. I'm looking for torque values for the three nuts at the top of the strut tower and for the two down the bottom of the strut....


  1. Install or connect the following:
    • Spring seat. Tighten the new upper strut retaining nut to 36 ft. lbs. (49 Nm).
  2. Remove the strut from the vise and disassemble the securing nuts and bolt.
  3. Rotate the upper support so the lowest bolt on the support aligns with the projection part of the lower spring.
  1. Install or connect the following:
  2. Strut and tighten the strut to body bolts to 59 ft. lbs. (80 Nm).
  • Strut to the steering knuckle and tighten the bolts to 156 ft. lbs. (211 Nm).
To install:
  1. Install the lower ball joint onto the steering knuckle and tighten nut to 90 ft. lbs. (123 Nm). Install new cotter pin.

Oct 30, 2009 | 2000 Lexus ES 300

1 Answer

Replace ball joints


Remove in this order: wheel, loosen the 4 lower ball joint set bolts, cotter pin and nut from tie rod, tie rod from ball joint bracket, ball joint from lower control arm, 4 lower ball joint set bolts, ball joint from suspension. Install is reverse but don't tighten the 4 lower ball joint set bolts.

torque is as follows:
ball joint to control arm- 112 ft-lbs
Tie rod nut- 67 ft-lbs
lower ball joint set bolts- 83 ft-lbs
remember to use a new cotter pin

Oct 08, 2008 | 2004 Toyota Tacoma

Not finding what you are looking for?
1996 GMC Jimmy Logo

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...