Question about 2006 Ford F-150

1 Answer

Trying to flush radiator, where is plug in block, or can I just take bottom hose off radiator, to drain all coolant.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 96 Answers

Go to auto zone/ O"rileys and buy a flush kit, it is a kit that allows you to cut, a heater hose and install a TEE with a cap on it, the cap end is also the hookup for a water hose, wait until the engine is cool, cut the hose install TEE, hook up water hose, remove radiator cap, turn water on low, crank engine and flush until water is clear, reinstall cap and your block,radiator is flushed, don"t forget to put in coolant

Posted on Sep 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to drain coolant


They do clog up and will not drain. You probably found the drain. Pull the lower radiator hose. If you have access to air and can shoot it up in the hole. This might help you problem.

Jul 08, 2015 | 1997 GMC Jimmy

1 Answer

How do i change the radiator fluid?


Most radiators have a drain plug on the bottom tank the engine block also has a drain plug . Remove the radiator cap ,open both drains ,let all the coolant run out, if there is no radiator plug remove the lower hose , remove the heater demister hoses, with the heater control on hot flush out all the coolant from the heater radiator. with a garden hose, till the water runs clean, tighten the radiator plug or re fit the hose,put a garden hose into the radiator and flush out till the water at the block plug runs clean ,refit the heater hoses, refit the block plug, fill the radiator from the hose leave the cap off , If it has a overflow tank clean and flush it. start and run engine for 5 minutes top up radiator if needed . stop engine and drain out all water. most important that all old coolant is drained out, only buy the best coolant you can . If you make up your own use only distilled water. keep some to top up with never mix with another brand. Fill radiator with coolant top up over flow tank, run engine top up coolant as needed, refit radiator cap run for another 10 minutes check for leaks,

Oct 14, 2014 | 2006 Chevrolet Trailblazer

1 Answer

How to back flush heater core 2007 grand prix


drain coolant system locate heater cores hoses going through firewall you need to buy the radiator flush kit at any auto parts stores. remove heater cores hoses from one end or buy extra long heater hoses same size as heater core hoses in vechicle at auto parts store use the flush kit when you flush through one of the heater core hoses let the other hose drain in a drain pan when you use home garden hose use low water pressure dont use garden hose to the max or you will rupture heater core. your best bet let radiator shop flush whole coolant system. because heater cores hoses are in a tight spot.make sure engine off if you just going to flush out heater core only .after flushing heater core good time to replace heater core hoses.if job too hard or complicated let radiator shop flush out radiator the engine block and heater core because if radiator stopped up or engine block stopped up the gunk and rust will reenter plug up heater core.if you tight on money you can flush out your own radiator.drain out radiator using large drain pan. remove top radiator hose and remove bottom radiator hoses connect to water pump.use garden hose with flush kit part with water pressure not too high put garden hose to top radiator hose run water until clear water run out bottom radiator hose in drain pan,the flush out engine block remove thermostat.if you had another spare thermostat housing with RTV SILICONE SEALANT THAT HAS SET UP INSTALL THERMOSTAT HOUSING BACK TO ENGINE WITHOUT THERMOSTAT FLUSH OUT THE ENGINE BLOCK, WHEN DONE INSTALL NEW THERMOSTAT THEN INSTALL ORIGINAL THERMOSTAT HOUSING WITH NEW ORING WHICH YOU BUY AT DEALERSHIP.IF ALL SOUND COMPLICATED LET RADIATOR SHOP FLUSH OUT COOLANT SYSTEM.

Nov 27, 2012 | 2003 Pontiac Grand Prix

1 Answer

Flushing antifreeze on a 2006 kia sorento


This procedure makes a bit of a mess and requires catch pans but it is the best way to flush a coolant system without cutting any hoses or adding a flush kit.


If your radiator does not have a drain plug is to remove the LARGE lower radiator hose and drain the anit-freeze. (Even if it does have a drain plug the steps below are the best way) You then plug the lower radiator hose connection on the radiator and have a 2nd person add water to the radiator with a hose. They will need to place a rag over the fill port for the radiator and flush the block until you get clear water from the lower drain hose. Once you get clear water drain off the fresh water by unblocking the lower radiator fitting and flush the radiator. Once you get cleanwater from the radiator connection, reconnect your lower radiator hose. (Tighten the clamp!) Then add your anti-freeze. Remember there will still be a some water in the block so do not be afraid to keep your anit-freeze / water ratio a tad higher because the left over water in the block will dilute it slightly.

Thanks for choosing FixYa,
Kelly

Aug 01, 2011 | 2003 Kia Sorento

2 Answers

I want to learn how to drain and flush my radiator. I need help on how to do so without making as mess


well its bound to make a little mess but you should have a drain plug on the radiator at the bottom towards the engine side on one of the 2 tanks (sides of radiator ) unscrew drain plug and let drain into a pail or pan ( 2 gallon ) after it drains remove lower radiator hose. use a garden hose and fill radiator and let it flush for a little, hook lower radiator hose back, tighten drain plug and fill with a 50/50 mix new antifreeze,

Feb 07, 2011 | 1996 Ford Taurus

3 Answers

Where is the engine coolant drain bolt on a 2003 2azfe camry? i found the radiator drain but can't find the engine drain plug-a photo would be great


The textbook method is to remove the drain plug on the bottom of the radiator.

Most drain plug is make of inexpensive nylon/plastic and it may fall apart while you turn it.

The professional method is to loosen the lower radiator clamp and drop to lower radiator hose.

Drain the coolant onto a large drain pan and recycle the coolant

===

I just did a FREE write up on air purge from coolant system and how to detect initial state of blown head gasket at the Fixya tip selection.

Click HERE

or follow link below.

http://www.fixya.com/cars/r3582329-how_to_inspectdiagnose_and_repair_minor_

Nov 17, 2009 | 2003 Toyota Camry

2 Answers

Where is the coolant block drain plug located on


None on the block, other than freeze plugs...
The only drain is on the bottom of the radiator (you knew that)...

I installed a Prestone motor flush kit and it flushes just fine, but does not "empty" the engine cavities. This is better, anyway.

You have to splice a "Tee" fitting into a convenient heater hose (highest one).

Hope this helps..

Sep 10, 2009 | 1998 Ford Escort

2 Answers

Engine block coolant drain plug


there is no coolant drain on the block. however take the lower radiator hose off and you should be able to get it to drain completely.

Aug 30, 2008 | 1997 Buick Skylark

1 Answer

Coolant drain plug on engine block


there is no drain plug on the engine block unfortunately, however taking the lower radiator hose off will drain almost all the coolant out off the block. then reconnect the lower hose and fill completely with just water and flush solution let sit for a few minutes. then take lower hose off again let it completely drain. reconnect lower hose and fill with 60/40 mix of coolant this will protect to -40 degrees F. when you have it completely full keep cap off radiator and start vehicle turn your heater on hot and the fan to high. top off with coolant and replace cap. there should be no need to bleed system of air. please rate this solution.

Aug 30, 2008 | 1997 Buick Skylark

Not finding what you are looking for?
2006 Ford F-150 Logo

310 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...