Question about 1999 GMC Jimmy

2 Answers

How do i bleed the abs ,or proportionate valve,brake shoes won,t release from disks (front)when warm,bled brakes but still trouble.

Posted by on

  • gvbiketourin Dec 03, 2009

    If lines are clogged how do I go about clearing lined from master to rubber.

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

If the front wheels drag when hot. drive the car, get it warm, lift up the car, try to turn the wheel, ck both wheels, now loosen one of the front caliper bleeders, do the wheels now turn? if so its a hydraulic problem. if it does not make a difference, then the caliper is bad.... IF letting the bleeders loose lets the wheel spin free,tighten the bleeder back up, now pump up the brake pedal till its stiff and now the wheel should be hard to turn again, now loosen the lines at the master cyl. do the wheels spin free or are the stiff still? IF they are still stiff, now loosen the front lines where the rubber line begins to go to the caliper. still stiff? now loosen the caliper, it should be free if it is then the front hoses are stopped up.........common.

Posted on Sep 25, 2009

Testimonial: "you guys are great! Thank for you time my friend!"

  • Ted Schore Sep 25, 2009

    it would help if you told of all the parts you replaced, we dont have a crystal ball.

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 432 Answers

Worn out caliper maybe. is it on one side??? if so may be a bad brake line.

Posted on Sep 25, 2009

Testimonial: "replaced calipers,shoes,disks,but never thought of a line thanks bud!"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why is the brake light on after putting front brakes on


Do you mean the brake lights on the rear of the vehicle or the brake light on the dash?

Jan 21, 2015 | 2002 Kia Amanti

1 Answer

Brakes won't release


does your model have an abs unit as this can be the fault, some areas when sold did not have this abs unit but with the abs unit it has valves to assist braking. if a piston in the abs has failed it stop it from working and only manual braking is used but this is limited.

Jun 13, 2017 | 1992 Honda Accord

1 Answer

Need to know procedure for bleeding brakes on1987 gmc s15 2.8 litre 4x4 front disc w/abs


MANUAL BLEEDING

For those of us who are not fortunate enough to have access to a power bleeding tool, the manual brake bleeding procedure will quite adequately remove air from the hydraulic system. The major difference between the pressure and manual bleeding procedures is that the manual method takes more time and will require help from an assistant. One person must depress the brake pedal, while another opens and closes the bleeder screws.

In addition to a length of clear neoprene bleeder hose, bleeder wrenches and a clear bleeder bottle (old plastic jar or drink bottle will suffice), bleeding late-model ABS systems may also require the use of one or more relatively inexpensive combination valve pressure bleeding tools (which are used to depress one or more valves in order to allow component/system bleeding). To fully bleed the late model ABS systems, a scan tool should also be used to run the system through functional tests.
  1. Clean the top of the master cylinder, remove the cover and fill the reservoirs with clean fluid. To prevent squirting fluid, and possibly damaging painted surfaces, install the cover during the procedure, but be sure to frequently check and top off the reservoirs with fresh fluid.
CAUTION Never reuse brake fluid which has been bled from the system.
  1. The master cylinder must be bled first if it is suspected to contain air. If the master cylinder was removed and bench bled before installation it must still be bled, but it should take less time and effort. Bleed the master cylinder as follows:
    1. Position a container under the master cylinder to catch the brake fluid.
WARNING Do not allow brake fluid to spill on or come in contact with the vehicle's finish as it will remove the paint. In case of a spill, immediately flush the area with water.
    1. Loosen the front brake line at the master cylinder and allow the fluid to flow from the front port.
    2. Have a friend depress the brake pedal slowly and hold (air and/or fluid should be expelled from the loose fitting). Tighten the line, then release the brake pedal and wait 15 seconds. Loosen the fitting and repeat until all air is removed from the master cylinder bore.
    3. When finished, tighten the line fitting to 20 ft. lbs. (5 Nm).
    4. Repeat the sequence at the master cylinder rear pipe fitting.
During the bleeding procedure, make sure your assistant does NOT release the brake pedal while a fitting is loosened or while a bleeder screw is opening. Air will be drawn back into the system.
  1. Check and refill the master cylinder reservoir.
Remember, if the reservoir is allowed to empty of fluid during the procedure, air will be drawn into the system and the bleeding procedure must be restarted at the master cylinder assembly.
  1. On late model ABS equipped vehicles, perform the special ABS procedures as described later in this section. On 4 wheel ABS systems the Brake Pressure Modulator Valve (BPMV) must be bled (if it has been replaced or if it is suspected to contain air) and on most Rear Wheel Anti-Lock (RWAL) systems the combination valve must be held open. In both cases, special combination valve depressor tools should be used during bleeding and a scan tool must be used for ABS function tests.
  1. If a single line or fitting was the only hydraulic line disconnected, then only the caliper(s) or wheel cylinder(s) affected by that line must be bled. If the master cylinder required bleeding, then all calipers and wheel cylinders must be bled in the proper sequence:
    1. Right rear
    2. Left rear
    3. Right front
    4. Left front
  2. Bleed the individual calipers or wheel cylinders as follows:
    1. Place a suitable wrench over the bleeder screw and attach a clear plastic hose over the screw end. Be sure the hose is seated snugly on the screw or you may be squirted with brake fluid.
Be very careful when bleeding wheel cylinders and brake calipers. The bleeder screws often rust in position and may easily break off if forced. Installing a new bleeder screw will often require removal of the component and may include overhaul or replacement of the wheel cylinder/caliper. To help prevent the possibility of breaking a bleeder screw, spray it with some penetrating oil before attempting to loosen it.
    1. Submerge the other end of the tube in a transparent container of clean brake fluid.
    2. Loosen the bleed screw, then have a friend apply the brake pedal slowly and hold. Tighten the bleed screw to 62 inch lbs. (7 Nm), release the brake pedal and wait 15 seconds. Repeat the sequence (including the 15 second pause) until all air is expelled from the caliper or cylinder.
    3. Tighten the bleeder screw to 62 inch lbs. (7 Nm) when finished.
  1. Check the pedal for a hard feeling with the engine not running. If the pedal is soft, repeat the bleeding procedure until a firm pedal is obtained.
  2. If the brake warning light is on, depress the brake pedal firmly. If there is no air in the system, the light will go out.
  3. After bleeding, make sure that a firm pedal is achieved before attempting to move the vehicle.

Hope helps (remember to rate this answer).

Apr 13, 2011 | 1987 GMC Jimmy

1 Answer

How to bleed brakes on 1997 Saturn


The brake system bleeding procedure differs for ABS and non-ABS vehicles. The following procedure pertains only to non-ABS vehicles. For details on bleeding ABS equipped vehicles, refer to the ABS procedures later in this section.

WARNING Make sure the master cylinder contains clean DOT 3 brake fluid at all times during the procedure.
  1. The master cylinder must be bled first if it is suspected of containing air. Bleed the master cylinder as follows:
    1. Position a container under the master cylinder to catch the brake fluid.
    2. Loosen the left front brake line (front upper port) at the master cylinder and allow the fluid to flow from the front port.
    3. Connect the line and tighten to 24 ft. lbs. (32 Nm).
    4. Have an assistant depress the brake pedal slowly one time and hold it down, while you loosen the front line to expel air from the master cylinder. Tighten the line, then release the brake pedal. Repeat until all air is removed from the master cylinder.
    5. Tighten the brake line to 24 ft. lbs. (32 Nm) when finished.
    6. Repeat these steps for the right front brake line (rear upper port) at the master cylinder.
WARNING Do not allow brake fluid to spill on or come in contact with the vehicle' finish, as it will remove the paint. In case of a spill, immediately flush the area with water.
  1. If a single line or fitting was the only hydraulic line disconnected, then only the caliper(s) or wheel cylinder(s) affected by that line must be bled. If the master cylinder required bleeding, then all calipers and wheel cylinders must be bled in the proper sequence:
    1. Right rear
    2. Left front
    3. Left rear
    4. Right front
  2. Bleed the individual calipers or wheel cylinders as follows:
    1. Place a suitable wrench over the bleeder screw and attach a clear plastic hose over the screw end.
    2. Submerge the other end in a transparent container of brake fluid.
    3. Loosen the bleed screw, then have an assistant apply the brake pedal slowly and hold it down. Close the bleed screw, then release the brake pedal. Repeat the sequence until all air is expelled from the caliper or cylinder.
    4. When finished, tighten the bleed screw to 97 inch lbs. (11 Nm) for the front, or 66 inch lbs. (7.5 Nm) for the rear.
  3. Check the pedal for a hard feeling with the engine not running. If the pedal is soft, repeat the bleeding procedure until a firm pedal is obtained.
zjlimited_349.jpg

Fig. 1: Loosen the front brake line in order to bleed the master cylinder

zjlimited_350.jpg

Fig. 2: Connect a bleed hose from the bleed valve on the front caliper to a jar of brake fluid

zjlimited_351.jpg

Fig. 3: Always follow the lettered sequence when bleeding the hydraulic brake system





Hope this helps to solve it; remember to rate this answer.

Dec 29, 2010 | 1997 Saturn SL

1 Answer

I hve a 96 chevy 1500 4wd with brake issues. ABS light is on in the dash. Have replaced both frt calipers, pads, hoses. Replaced rear brakes and drums. Replaced master cylinder. Bled two quarts of...


you may have air trapped in the ABS EHCU. Did you use this procedure?

Bleeding the EHCU

Bleeding the EHCU requires the use of the TECH-1 scanner or its equivalent and the appropriate cartridge. Additionally, 3 tools, J-39177 or equivalent, are required. Bleeding cannot be performed without this equipment.
The EHCU must be bled after replacement or if air is trapped within the unit. It must be bled after bleeding the master cylinder and before bleeding the individual wheel circuits.
The Internal Bleed Valves on either side of the unit must be opened 1 / 4 - 1 / 2 turn before bleeding begins. These valves open internal passages within the unit. Actual bleeding is performed at the two bleeders on the front of the EHCU module. The bleeders must not be opened when the system is not pressurized. The ignition switch must be OFF or false trouble codes may be set.
  1. Open the internal bleed valve 1 / 4 - 1 / 2 turn each.
  2. Install one tool J-39177 on the left bleed stem of the EHCU. Install one tool on the right bleed stem and install the third tool on the combination valve.
  3. Inspect the fluid level in the master cylinder, filling if needed.
  4. Slowly depress the brake pedal and hold it down.
  5. Open the left bleeder on the front of the unit. Allow fluid to flow until no air is seen or until the brake pedal bottoms.
  6. Close the left bleeder, then slowly release the pedal. Wait 15 seconds.
  7. Repeat Steps 4, 5 and 6, including the 15 second wait, until no air is seen in the fluid.
  8. Tighten the left internal bleed valve to 5 ft. lbs. (7 Nm).
  9. Repeat Steps 3-7 at the right bleeder on the front of the unit.
  10. When bleeding of the right port is complete, tighten the right internal bleed valve to 5 ft. lbs. (7 Nm).
  11. Remove the 3 special tools.
  12. Check the master cylinder fluid level, refilling as necessary.
  13. Bleed the individual brake circuits at each wheel.
  14. Switch the ignition ON . Use the hand scanner to perform 3 function tests on the system.
  15. Carefully test drive the vehicle at moderate speeds; check for proper pedal feel and brake operation. If any problem is noted in feel or function, repeat the entire bleeding procedure.

Oct 10, 2010 | Chevrolet 1500 Cars & Trucks

1 Answer

How to trouble shoot the brake system?


To trouble shoot the brake system you have to check:AntiLock Brake System ABS:
Hydraulic Modulator
Basically this unit holds steady or bleeds off pressure in brake line, as necessary, when the Electronic Brake Control Module (EBCM) detects an abnormal deceleration in the speed of the wheel. On 2000 and later models the EBCM and Brake Pressure Modulator Valve (BPMV) are mounted on a bracket attached on the left strut tower.
Wheel Speed Sensors, brake fluid level, brake hoses and lines, inspect and replacement, Brake hydraulic system-bleeding, Brake light switch, check, adjustment and replacement.
Disk brake caliper, disk brake pads, drum brake shoes, master cylinder, master cylinder reservoir, O-rings replacement, parking brake adjustment, parking brake cables inspect and replacement, parking brake shoes-replacement, power brake booster, check or replacement, wheel cylinder inspect and replace.

Oct 10, 2010 | 2000 Chevrolet Venture

2 Answers

Spongy brake pedal even after ABS bleed and base brake bleed.


Did you adjust the rear shoes out? If the rear drum brakes are out of adjustment they will give you a lot of pedal travel. If the pads are worn have no fear of that U-CLIP brake spring, just change one shoe at a time. Take the spring off one side, change the shoe, put the spring back on the post and do the same to the other shoe, no problem.

Dec 03, 2009 | 2001 Chevrolet Venture

2 Answers

Rear brakes locking(until abs kicks in) with little front brake application and very light pedal pressure. also have really poor hard/emergency braking response, vehicle doesnt stop as aggresively as it...


It could be a proportioning valve, and there's also the chance that the portion of the master cylinder that operates the front brakes is going bad. Have you had a pressure check done on the front brake system? Also, some vehicles have a variable proportioning valve, so that when the vehicle is loaded, it allows more pressure to the rear brakes. These can sometimes stick in place, causing the fault that you describe. Hope this helps you out.

Dec 01, 2009 | 2002 Dodge Durango

2 Answers

1999 Chevy Tahoe- Soft Brake Pedal


Try having the dealer flush and bleed your system. It is very hard to bleed ABS systems yourself and have safe brakes that still work afterward. Bleeding non-ABS brakes yourself is easy not the same for ABS brakes. Valving, sensors and what-not require a tech and the correct equipment in my opinion. You do it wrong and you could ruin your ABS system. Do that and see if they firm up. I replaced my brake shoes/pads at the same time all new everything in back, drums/springs everything and new rotors up front. then I had the chevy dealer flush, refill and bleed system. Stiffer pedal and brakes work better. Keep in mind the brakes on 99 Tahoes are inaedequate, require new rotors often, heat up and fade/glaze pads regularly. I replace my pads long before they wear down because they glaze up and start fading early. I'll rough em up once maybe, next time, new ones. Every two brake jobs, new rotors for me. Just how it is. They will stiffen a bit and work better but they will never be awesome brakes. Just how it is on 99 and earlier Tahoes. Hope it helps. Very important to bleed correctly though. I'll bleed my 83 Toyota 4x4 myself but not the Tahoe.

Aug 06, 2009 | 1999 Chevrolet Tahoe

2 Answers

Brakes feel spongy.when pressed hard goes nearly to floor.if pedal released slightly and pressed again feels normal.this is a 1997 toyota caldina GGT with abs.have bled brakes and sgimmed discs.any ideas?


Either you did not bleed the brakes properly or they need adjusted. (rear only) Front most likely are disks. If you put pads on the front and spread the caliper pistons, you should pump the brake pedal 10 or 15 times to move the pistons out. Some ABS systems are notoriously hard to bleed.

Apr 04, 2009 | 1997 Toyota Celica

Not finding what you are looking for?
1999 GMC Jimmy Logo

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...