Question about 1994 Volkswagen Jetta

1 Answer

Replaced timimg belt and idle pulley on 1994 jetta it wont stay idled

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 432 Answers

Did you remove the intake could be sucking air??? Did you time it right to specs.check vaccum lines

Posted on Sep 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1994 ford ranger 2.3 runs fine wont stay idling


Try TPS. Throttle positioning Sensor. This sets base idle. (Unless this model is too old for that sensor)

Sep 21, 2014 | 1994 Ford Ranger Supercab

1 Answer

Timing belt keeps breaking


with the timing belt off check the water pump make sue it moves round easily if not replace. check the movement of the cams as well. would say it was the water pump at fault. they should be changed at the same time as the belt.

Feb 25, 2013 | 2005 Opel Corsa 1.4

1 Answer

I need to replace the alternator belt on a 1994 Volvo 940T, but can't get the A/C belt off so I can remove the alternator belt. Apparently there's an adjustment bolt on the compressor that I...


Hi,
Unscrew the idle pulley first.
Look for a small pulley where the a/c belt passes through. That is the idle pulley, the screw on the bracket of that idle is on the top side where you could adjust to loosen the tension of the belt. Before loosening it, loosen the bolt on the front of idle pulley.
Hope FixYa helps you out!

Aug 28, 2011 | 1993 Volvo 940

2 Answers

Need serpentine belt routing diagram for 1994 Dodge grand caravan


3.3L?
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!

Jan 21, 2010 | 1994 Dodge Grand Caravan

1 Answer

On my 2006 Volkswagen Jetta TDI, The Serpentine belt has shreaded 4 times. The pulley has been replaced once but it still does the same thing. The Dealer cannot determine the cause.


Can you check , visually wether the belt is running in a smooth straight line. Check with the engine idling and also throttling up, see if it is moving from side to side. This would indicate that there is play at one of the pulleys. Also check each pulley belt surface for any abnormalities, marking etc.
hope this helps

Nov 04, 2009 | Volkswagen Jetta Cars & Trucks

1 Answer

How do you rerout the belt on a 1994 buick roadmaster estate wagon when not using a c pulley...The ac pulley and clutch has seized up.


You will need to get an idle pully, remove the air con. pump and fit the idle pully in its place. You may be able to reroute the belt but getting a belt to fit will be a problem.

Sep 10, 2009 | 1994 Buick Roadmaster

1 Answer

How do I tighten the ac belt on my 94 isuzu pickup?


Undo nut on idle pulley and then turn the adjustment screw and re-tighten nut on idle pulley

Jul 15, 2009 | 1994 Isuzu Pickup

1 Answer

Serpentine belt slips off idler pulley


The A/C pully is supposed to spin freely until the AC is activated to run.. The cranshaft pully does not. Replace the tensioner pully. The belt has to fit in between the grooves on the pullys.

Apr 05, 2009 | 1994 GMC Suburban

2 Answers

2001 camry was at idle and engine shut off..


Hi There,
Is this a 4 or 6 cylinder? How many miles?

Mar 27, 2009 | 2001 Toyota Camry

Not finding what you are looking for?
1994 Volkswagen Jetta Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...