Question about Toyota Corolla

1 Answer

1992 toyota corolla, stiff brakes after driving several miles in

1992 toyota corolla, initial problem was brake pedal became stiff after several miles and some braking. This would cause passenger front brake to engage enough to cause vibration and require extra gas and downshift to continue. Brakes never locked. Replaced calipers, brake lines, pucks. hapeenend again within 20 miles. Used the car imtermittently vibrated intermittently. Did some research replaced the master cylinder this weekend. Problem still occurs but only intermittently. Happened again today and when I stopped to make a left turn pressed the pedal as hard as I could. By the time I got home 1 mile later the problem was subsiding. Problem subsides if I let the car idle for several minutes without the brake engaged or turn off the car for the same amount of time. Any ideas. Vacuum leak or is it the b power booster?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 750 Answers

Remove the master cylinder and check the plunger projection make shore it is with in specs, using a vacuum pump check condition of capsule see if it holds the preasure and its not leaking off. if its leaking change capsule and check valve

Posted on Sep 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

92 toyoto corolla, 3rd brake light,tail light and stop lights stay on after i turn the other lights on.


Your brake light switch is stuck. It is located under the dash, near the top of the brake pedal. Replace it with a new one.

Dec 26, 2010 | 1992 Toyota Corolla

1 Answer

Took my 93' Toyota, has 193,000 miles replaced the


THE MASTER CYLINDER NEED TO BE BLED FIRST.BEFORE PUTTING ON THE CAR.TO MANUAL BLEED BRAKE SYSTEM.YOU NEED 2 PEOPLE TO DO A BETTER JOB.YOU FIRST BLEED THE LEFT REAR RIGHT REAR LEFT FRONT AND RIGHT FRONT. WHEN YOU BLEED THE BRAKES.HAVE THE HELPER PUMP BRAKES 3 PUMPS.AND HOLD BRAKE PEDAL IN.YOU NEED A CLEAR BLEEDER HOSE IN A CLEAR BOTTLE HALF WITH CLEAN BRAKE FLUID. WITH BLEEDER HOSE ON BLEEDER SCREW AND OTHER END BLEEDER HOSE IN BOTTLE OF BRAKE FLUID.WHILE HELPER PUMP BRAKE PEDAL HOLD IT IN OPEN BLEEDER SCREW 1/4 TURN ALLOWING AIR BUBBLES LEAVE THE BRAKE SYSTEM.CLOSE THE BLEEDER SCREW BEFORE BRAKE PEDAL RELEASE.HAVE HELPER PUMP BRAKE PEDAL 3 TIMES. WITH PEDAL HELD DOWN OPEN BLEEDER SCREW GETTING AIR OUT OF THE SYSTEM.WHEN YOU SEE SOLID FLUID COMING OUT OF BLEEDER HOSE THE AIR IS OUT THE BRAKE SYSTEM.DONT DRIVE CAR ON HIGHWAY IF YOU STILL CANT GET SOLID BRAKES. HAVE CAR TOWED IN TO BE PRESSURE BLEED.

Jun 19, 2010 | 1993 Toyota Corolla

1 Answer

I have a 1992 corolla brake peddal pulsalating?


if you can drive 50 mph and push on the brake pedal lightly and the steering wheel pulsates, the front rotors are warped. new does not mean straight, and cheap never means good. If you feel it in the pedal or your **** then the most likely problem is the rear brakes,.

Jun 03, 2010 | 1992 Toyota Corolla

1 Answer

My 96 t100 brake pedal just became very stiff and the check engine light came on (refrencing a code of a possible vacumm leak)any ideas?


Hi:
You have a vacuum leak for sure. It could be in the power brake booster, or the vacuum hose that feeds it. The reason your brakes got stiff is you lost your power brakes, so your next thing to do is to try to find your leak!

Nov 12, 2009 | 1998 Toyota T100

1 Answer

93 dodge dynasty brake pedal stiff wont apply brakes


your power brake booster needs replaced ,it work off engine vacuum and when the seal inside leak there is no power assist for the brakes

Mar 06, 2009 | 1993 Dodge Dynasty

1 Answer

2003 toyota corolla low brake fluid


The fluid level will drop when the brake pads and or shoes wear thinner. A good way to check for a hydraulic fluid leak is Shut engine off step down on the brake pedal and hold it for 3 minutes. The pedal should not slowly drop. It will go down and hold.

Feb 28, 2009 | 2003 Toyota Corolla

1 Answer

2009 Toyota Corolla


1st, is your foot on the brake? That's a safety feature, u must depress the brake pedal before u can shift out of park.

Jan 15, 2009 | 2009 Toyota Corolla

1 Answer

1992 toyota corolla


check if it is brake fluid. could be coming from the oil seal and passing to the push rod towards the pedal.


tnx 4 using fixya,

drcool

Oct 19, 2008 | 2007 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...