Question about 1986 Jeep CJ7

2 Answers

When replacing the front rotors on a 86 cj7 jeep 6 cyl is it necessary to remove the hubs? or will the rotors come right off?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 23 Answers

I agree with fewwhiskers. One thing to remember though, have an old hanger closeby to wire the calipers up so they don't hang by the hoses. That can cause them to leak.

Posted on Oct 09, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Rotors comes off front side

Posted on Oct 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to repack front wheel bearings on a 98 Jeep Cherokee 4X4


YOU CAN"T is the short answer..... sorry,, RTM much>?
ive posted the free fsm like 300 times now on this car.
ever like search.?
first off, on all cars made, what the factory made or dealer sells ins one thing, what the after market does, is another.
a fact.
in fact some cars with Integrated hubs new, the aftermarket sells them and sells the rebuild kits too.
the book covers the service step by step.
what parts you use or by is your call.

now ill read that book for you.
btw I sold my 99 but not the books.
XJ jeep, the book is here, (over 301 posted,)

http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service

at least you said its 4wd, not all are. 2points for that.

USA XJ jeep, 1998.
1988 pages.
the trick is learning how to navigate the book , chapter #
the fact is we look first, you didn't, what is there who knows.?
maybe the last shop put on serviceable hubs. right?
if you had looked at the back side, you'd have seen 3 bolts
holding it on. and that tells you what?, that they are integrated hubs.
on new car, and at Jeep parts counters. world wide.



26271221-ky1blxw0v1am10ilppsnvnq2-3-0.jpgnow lets do this backwards
lets pretend to buy the part, hark , you can online.
and see all the makers of parts aftermarket in 1 click
no kidding, a fact.
see the 8 makers here,(can be more)
all are 100% integrated, hubs, (not saying there are not other makers, or kits, the world is a huge place and I cant tell you
all answers world wide for sources)

you could off them, take them both to a shop, and ask for them to rebuild them at $100 /hr labor, but, i bet they just laugh at you.
I'm not. but why not just remove it , check it and if bad replace it.
take it to any auto-store in town, NAPA is best. and set it on the counter, and say, got this, answer yes.
how to repack unpackable bearings,.DIY.

shorter answer, R&R it.
get a shop to fix it.
buy the part first, and see what you got first.
look at it and ponder packing it.

Aug 31, 2016 | 1998 Jeep Cherokee

1 Answer

Front end noise


check u-jounts and motor mounts and usually vib during braking is either rotors or hub

Jul 17, 2017 | 1997 Jeep Grand Cherokee

1 Answer

How do I change the front wheel bearing in a 2001 Sonata 6 cyl


jack the front off the ground remove the tire remove the brake caliper remove the rotor remove the bolt hol;ding the front axle into the spindle hub, remove the hub and bearing.

May 06, 2010 | 2001 Hyundai Sonata

1 Answer

Cannot remove front rotor. Caliper and pads


Raise vehicle and remove wheels. Disconnect brakeli
ne from caliper (if necessary). Remove caliper.

On models with free wheeling hub, set control handl
e to FREE position. On all models, remove hub
cover, bolt/washer and hub body. Use tapered punch
to open slits of conical washers. Remove axle shaft

snap ring (if equipped).

Straighten tabs of outer lock washer. Using Spindle
Socket (09607-60020), remove lock nut, lock washer

and adjusting nut. Remove thrust washer and outer b
earing. Remove axle hub and rotor. Remove grease se
al
and inner bearing. Press hub bolts out of axle hub.
Remove retaining bolts, and separate rotor from hu
b.

Mar 20, 2010 | 1996 Toyota Land Cruiser

1 Answer

Where is the headlight fuse located for a 1986 CJ7?


1986 or 1983? if 1986 need to know if 4 cyl or 6 cyl engine

Feb 07, 2010 | 1983 Jeep CJ7

1 Answer

I hear a high pitched scraping sound when I press down on my brakes to come to a stop. I need to know if that means the brakes need to be replaced and if so how do I do that? I've done a brake pad...


No it won't, but it should be easier. The 70's CJ7 was a hub and rotor assembly. The Honda is just a disc rotor. Remove the wheel, caliper and bracket and then the rotor should just come off. Reverse the way you took it apart and fit in the new pads after pressing the caliper piston back in.

Aug 04, 2009 | 1998 Honda Civic

1 Answer

86 pick-up chev


you should see 6 small allen screws around hub,remove these and outer hub will slide off. then there will be a snap ring around axle remove this and also will be a large ring around outer part of hub and inside the rotor hub. remove this one and hub will slide out

Jan 22, 2009 | 1986 Chevrolet C1500

1 Answer

Remove the front disc rotor


The rotor and hub assembly are held together by the studs,you must first remove the 4-wheel drive hub assembly,then the wheel bearing nuts,and pull the hub and rotor off as a unit. Next lay it(back down) on a piece of wood, using a drift punch drive the studs out. Turn it over ,lay it(face down) on a block of wood, line the new stud splines up with the grooves in the hub and drive them in with the punch and reassemble. A set of dentist style picks will be helpful with the clip in the 4wd hub and a 4 lug 4wd nut wrench will be needed.

Dec 26, 2008 | 1979 Chevrolet C/K 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...