Question about 1997 Chevrolet Blazer

1 Answer

Windshield wipers do not operate all the time; where do I find the fuse box; how do I replace head lamp/bulb?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 753 Answers

The blazer had problems with wiper circuit board contacts the board is mounted to the wiper motor if you replace this it has fixed 99% of the ones I have repaired.If you remove the front grille you will be able to access the back of the composit headlamp assembly to unplug bulb and remove it.

Posted on Sep 24, 2009

Testimonial: "thank you for the information; truly appreciated"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wipers will not turn on 2006 colorado


There are two relay's in the under hood fuse / relay box . Wiper relay an wiper relay 2 . Maybe one is bad . also check fuse #14 25 amp. Wiper fuse.Plus the BCM - body control module has a hand in making the wipers work . Are you familiar with automotive electronic control modules ?
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Do you have any speed !

Oct 06, 2017 | Cars & Trucks

1 Answer

WHERE IS THE WIPER/WASHER FUSE LOCATED ON 2007 PONTIAC TORRENT


In the under hood fuse box , should have diagram inside the lid . Front wiper's or rear ? Front fuse # 36 - 25 amp. Plus Two relay's PCB hi and Wiper PCB relay . Wouldn't think this being fuse problem . Wiper switch , motor etc... The wiper's are control by a computer . BCM - body control module .

The windshield wiper/washer system consists of front and rear wipers. The front and rear wipers are operative when the vehicle is in accessory or run. The front wipers have 4 different modes: Mist, Intermittent, Low, and High. When the front wipers are in the intermittent mode, there are 5 delay modes to chose from, commanded by the windshield wiper washer switch through the body control module (BCM). The rear wipers has an only one mode.

If the fuse is bad , could have a short to ground or wiper motor pulling to much current (amps) . Fuse's don't just blow for no reason ! Could also have DTC'S - diagnostic trouble codes stored in the BCM .
DTC B3715
DTC B3873
DTC B3875
DTC B3922

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
The BCM controls the windshield wiper motor through two output controls, controlling two different PCB relays which control the desired wiper speed, high or low.
DTC B3922 00: Front Wiper Function Select Circuit

The PCB relay's are non- servicable , replace fuse box . Soldered in Your best bet mit be to take it to a qualified repair shop .

Feb 20, 2017 | Pontiac Cars & Trucks

1 Answer

2005 ford escape wiper and washer has no power. cant hear it engage when on but was working a week ago. how can i troubleshoot it and find the fuse


Hi Justin , Do you know what a SJB - smart junction box is and where it is located on you escape ?
Windshield Wiper Operation
The smart junction box (SJB) supplies power to the multifunction switch from the SJB fuse 25 (20A) when the ignition switch is in the ON or ACC position. The multifunction switch supplies power to the windshield wiper motor for the HIGH or LOW/INTERMITTENT input, depending on the multifunction switch position selected. The SJB also supplies power directly to the windshield wiper motor from fuse 25 (20A) when the ignition switch is in the ON or ACC position for RUN/PARK operation. When the multifunction switch is in the LOW, HIGH, or INTERMITTENT position, power is supplied to the windshield wiper motor, which moves the wipers off the park position. Once the wipers are off the park position, an internal switch in the windshield wiper motor switches to the run/park position which directs power to the wiper switch then back to the wiper motor. This maintains power to the windshield wiper motor to complete the wipe cycle. When the cycle is complete, the internal switch in the windshield wiper motor switches back to the park position. If the multifunction switch is in the LOW or HIGH position, power is supplied from the multifunction switch and another wipe cycle starts. If the multifunction switch is in the INTERMITTENT position, the windshield wipers remain parked until the internal relay in the multifunction switch supplies power to the windshield wiper motor. The internal relay supplies power after a time delay that is determined by the 1 of 9 intermittent switch settings.

Jan 08, 2017 | 2005 Ford Escape

1 Answer

2003 Pontiac Montana wipers not working how to fix


First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

Nov 25, 2016 | 2003 Pontiac Montana

2 Answers

Where is the windshield wiper fuse located in the fuse box on a 06 crown victoria


drivers side inner fender under the hood, look in the owners manual for the number and amps. some are marked under the lid itself

Mar 19, 2015 | 2006 Ford Crown Victoria

2 Answers

I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
Visual Inspection Chart Mechanical Electrical
  • Windshield washer pump hoses
  • Windshield wiper mounting arm and pivot shaft
  • Bussed electrical center (BEC) fuse 10 (30A)
  • Smart junction box (SJB) fuse 3 (10A)
  • Circuitry
  • Windshield wiper motor
  • Windshield washer pump
  • Windshield wiper/washer switch
  • The wipers stay on continuously
  • Circuitry
  • Windshield wiper motor
  • Windshield wiper/washer switch
  • Go To Pinpoint Test C .
PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
  • Key in OFF position.
  • Disconnect: Windshield Wiper/Washer Switch C2137.
  • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Does the windshield wiper/washer switch pass the component test?
Yes
GO to C2 .

No
INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
  • Disconnect: Windshield Wiper Motor C125.
  • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

    Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

    s6b~tr~en~file=n0011980.gif~gen~ref.gif
  • Are the resistances greater than 10,000 ohms?
Yes
GO to C3 .

No
REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
  • Disconnect all the windshield wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all the windshield wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
You

Feb 20, 2015 | 2007 Ford Mustang Coupe

1 Answer

I need a fuse box diagram for a 1985 1.3 Opel Kadett Cub


I found these on a site I'm assuming they're in order from number 1
Layout Diagram Parts: Direction signal lamps, Right tail lamp, license plate lamp, instrument lights, Left tail lamp, Interior lamp, Heater motor, stop lights, Horn, windshield wiper
if the fuse is good and the wires are not broken or disconnected it may be the wiper motor is bad

Feb 18, 2015 | Opel Cars & Trucks

2 Answers

Where is the fuse box for the wipers


It is under the dash panel right hand side , kick panel ? Fuse F1.1 10amp . an fuse F1.113 30 amp.
Visual Inspection Chart Mechanical Electrical
  • Windshield washer hoses
  • Wiper linkage
  • Multifunction switch
  • CJB fuses:
    • 1 (10A)
    • 38 (25A)
    • 113 (30A)
  • Circuitry
  • Windshield wiper motor
  • The windshield wipers are inoperative
  • Multifunction switch.
  • Circuitry.
  • Ignition switch.
  • Windshield wiper motor.
  • Go To Pinpoint Test A .
PINPOINT TEST A: THE WINDSHIELD WIPERS ARE INOPERATIVE Test Step Result / Action to Take A1 CHECK CIRCUITS 65 (DG) AND 1002 (BK/PK) FOR VOLTAGE
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Key in ON position.
  • Measure the voltage between windshield wiper C125 pin 5, circuit 65 (DG), harness side and ground; and between windshield wiper motor C125 pin 8, circuit 1002 (BK/PK), harness side and ground.
    s3j~tr~en~file=a0039065.gif~gen~ref.gif
  • Are the voltages greater than 10 volts?
Yes
GO to A2 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A2 CHECK CIRCUITS 57 (BK) AND 875 (BK/LB) FOR OPENS
  • Key in OFF position.
  • Measure the resistance between windshield wiper C125 pin 6, circuit 57 (BK), harness side and ground; and between windshield wiper motor C125 pin 3, circuit 875 (BK/LB), harness side and ground.
    s3j~tr~en~file=a0037610.gif~gen~ref.gif
  • Are the resistances less than 5 ohms?
Yes
GO to A3 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A3 CHECK THE MULTIFUNCTION SWITCH
  • Disconnect: Multifunction Switch C202a.
  • Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Did the multifunction switch pass the component test?
Yes
GO to A4 .

No
INSTALL a new multifunction switch. REFER to Section 211-05 . A4 CHECK CIRCUIT 57 (BK) FOR OPEN
  • Measure the resistance between C202a pin 4, circuit 57 (BK), harness side and ground.
    s3j~tr~en~file=a0045222.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
GO to A5 .

No
REPAIR the circuit. TEST the system for normal operation. A5 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR OPENS
  • Using the following table, measure the resistance between the multifunction switch C202a harness side and the windshield wiper motor C125 harness side:

    Multifunction Switch C202a Windshield Wiper Motor C125 pin 7, circuit 56 (DB/OG) pin 10, circuit 56 (DB/OG) pin 3, circuit 58 (WH) pin 11, circuit 58 (WH) pin 5, circuit 61 (YE/RD) pin 1, circuit 61 (YE/RD) pin 1, circuit 63 (RD) pin 9, circuit 63 (RD)

    s3j~tr~en~file=a0045221.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
GO to A6 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A6 CHECK FOR CORRECT WIPER MOTOR OPERATION
  • Disconnect all wiper motor connectors.
  • Check for:
    • corrosion
    • pushed-out pins
  • Connect all wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
GO to A7 .

No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation. A7 CHECK THE WINDSHIELD WIPER MOTOR
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Carry out the windshield wiper motor component test as described in this section.
  • Did the windshield wiper motor pass the component test?
Yes
The system is operating correctly at this time. Concern may have been caused by binding or incorrect pivot arm adjustment. REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

No
INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section. Hope this helps !

Feb 16, 2015 | 2002 Ford Expedition

2 Answers

Windshield wipers


Look for the fuse box under the dashboard, and look at the diagram on the cover for the proper location of the fuse, and use a plier (if you dont have fuse puller (small plastic one)), and gentle hold the fuse and pull it out carefully.

Mar 06, 2014 | 2006 Toyota Camry

Not finding what you are looking for?
1997 Chevrolet Blazer Logo

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...