Question about 2002 Kia Sedona

1 Answer

My back door/liftgate was open according to the sensor, but was not open, I went to double check it and opened the door, the plastic around the latch is torn and not it will not latch when I go to close it. Help!!

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 4 Answers

Take it off and replace it from Kia or a junk yard or just leave it off. The latch may just need adjusting too

Posted on Sep 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the manual liftgate sensor located 2009 Equinox


The liftgate can be opened by operating the switch on the instrument panel. Battery voltage is supplied to the liftgate actuator through the body control module (BCM). The BCM will pulse the liftgate actuator when a release input is received through the key fob, or the instrument panel switch.
Not sure what your talking about . There is no sensor. there is a relay in the I/P fuse box LIFTGATE PCB relay . an a lift gate actuator motor inside the door . An there is a door ajar switch ,which is part of the latch mechanism. Do you have light lit on the instrument cluster - a picture of a little car with a door open , an maybe a chime sounding ?

Not

Aug 01, 2015 | 2009 Chevrolet Equinox

1 Answer

How to replace a Liftgate Latch Handle on a 2005 Chevrolet Uplander?


First of you need to take the panel of the rear door from the inside then you can just grab the rod and pop it open. With the door panel off it is an easy thing to replace the handle just a couple screws are bolts to take lose .Also make sure you put the rods back just like you take them off may I suggest taking a picture if you can of the latch inside the door. Good luck.

May 14, 2014 | 2005 Chevrolet Uplander

1 Answer

2008 pontiac torrent liftgate wont open


First does it work manually? If it does than it must be checked electrically within the rear hatch behind the panel. You cold jump the switch but be careful not to short out the body control module.

Dec 27, 2013 | Pontiac Torrent Cars & Trucks

1 Answer

Liftgate problem


ON MOST LIFTGATES AFTER A WHILE TEND TO WEAR OUT THE PLASTIC FASTENER THAT HOLDS METAL ARMS OF THE LATCH,AND FELL OF..ON BACK OF LIFT GATE THERE SHOULD BE A DOOR HEL BY SCREWS TAKE THEM OFF TO SEE IF METAL ARMS ARE CONEECTED TO LIFT GATE HANDLE..LOOK AT LATCH YOU OPEN LIFT GATE WITH SCREWS SOMTIMES THERE TOO RE MOVE TO CHECK METAL ARMS,,,MOST PARTS STORES CARRY THESE FASTENERS FOR A COUPLE OF BUCKS..

May 25, 2013 | Dodge Cars & Trucks

1 Answer

Cannot open liftgate.manual says open liftgate to repair.How do I do that?


The plastic trim pops off at the top around the window. the bottm part will pop off enough to reach down and find the linkage to open the door. the linkage you want to find runs up and down. pull it up or push it down to open. there will be several rods to try. Once you get it open there are two screws on the bottom of the panel to remove it completely. then you can see and access the latch, handle, rods.

Jun 28, 2011 | 2003 Saturn VUE

1 Answer

How to open liftgate taht is locked its venture 2000, the key wont open. is there any manual way to open the liftgate that is locked from inside ?


there are 2 ways,one is you can use a dent puller and pull the lock out of the tailgate and use a slot screw driver to open the door,be aware that you could do a little damage around were the lock assembly is but it can be fixed.the other is to remove the interior door panel to get to the inner assembly and open it from inside the door panel.be aware that its a 2000 car and plastic components dry out and crack when pulling on them.

Jun 09, 2011 | 2000 Chevrolet Venture

1 Answer

2006 Tahoe Z71 Lift Gate Will Not Unlock With Remote


Take the liftgate inside panel off an check the wiring , connections etc....
rear door hatch lock repair GMC Chevrolet
chevy tahoe lift gate not opening
The liftgate will lock any time the vehicle is shifted out of park on vehicles equipped with an automatic transmission and at vehicle speeds exceeding 5 kph with manual transmission. This happens in conjunction with auto door locks if enabled or independently of auto door locks if the feature is disabled. This ensures that the liftgate is locked anytime the vehicle is shifted out of park or when the vehicle is in motion.
The liftgate lock relay supply and coil sides receive a constant voltage through the battery voltage supply circuit and the ECC fuse. The normally closed contact is connected to ground and the control side is connected to the body control module (BCM). A lock function will occur when a door lock switch activation, keyless entry lock transmission, auto door lock function or a liftgate lock function has been received by the BCM. The BCM will then ground the control side of the liftgate lock relay. This energizes the relay and allows voltage to be applied to the liftgate lock actuator lock control circuit. Since the other side of the liftgate lock actuator is connected to the normally closed contacts of the door unlock relay to ground, the liftgate will lock. When an unlock function occurs the BCM will ground the control side of the unlock relay and the rear doors and liftgate will unlock.
The BCM also runs diagnostics on the liftgate lock relay control circuit and will set DTC B3825 as current and also send a Class 2 message to the DIC. The DIC will display REPLACE LIFTGATE FUSE to inform the driver that a fault has been detected in the liftgate lock circuit and that the liftgate is not locked. Faults that will set the DTC and cause the DIC to display the message could be any of the following

Power Door Locks Inoperative - Endgate/Liftgate

Schematic Reference: Door Lock/Indicator Schematics
Connector End View Reference: Power Door Systems Connector End Views
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Activate the door lock switches to the lock and unlock positions.
Do both rear passenger doors lock and unlock?
YES - Go to Step 3
NO - Go to Power Door Locks Inoperative
3
Did the liftgate lock actuator lock and unlock?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 4
4
Disconnect liftgate door lock actuator.
With a test lamp connected to a good ground, probe the door lock actuator lock circuit at the door lock actuator harness connector.
Activate a door lock switch to lock position.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 7
5
With a test lamp connected to a good ground, probe the door lock actuator unlock circuit at the door lock actuator harness connector.
Activate a door lock switch to unlock position.
Does the test lamp illuminate?
YES - Go to Step 6
NO - Go to Step 8
6
Inspect for poor connections at the harness connector of the door lock actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 10
NO .. Go to Step 9
7
Repair the open door lock actuator lock circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 10
--
8
Repair the open in the door lock actuator unlock circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 10
--
9
Replace the liftgate door lock actuator. Refer to Door Lock Actuator Replacement in Body Rear End.
Did you complete the repair?
Go to Step 10
--
10
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Apr 27, 2017 | 2006 Chevrolet Tahoe

1 Answer

Door Open Warning Relay not working on driver door


The sensors are on all the door latches in all the doors and glass. You have to figure out which one is sticking open for example the drivers door switch and passengers door switch have the same color wires they are grey with a red tracer and black when you close the door both of the wires should be grounded when you open the door the ground should go away and you should have an open to ground. You will have to check all of your door switches the same way execpt for the rear liftgate and glass. The rear liftgate switch must be closed and have grounds on both sides of the wiring at the switch to supply the ground to one side of the switch of the liftgate glass ajar switch. I hope you find your problem.

Apr 09, 2009 | 2004 Ford Explorer

1 Answer

Power liftgate doesn't work


The power liftgate motor is located on the driver side panel directly behind the lift arm. First you will have to take the safety belt bolt out. After you get the plastic piece free from the body you will have to take the bolt out of the arm that connects to the hatch. Make sure you have a big enough torx bit for the bolt that holds the arm to the gate. This will allow you to slide the plastic piece off and out of your way. If you are having trouble getting the plastic piece to come off from around the liftgate arm, try putting the door down, that helped me. The rest should be easy. Hope this info helped you out. 

Mar 28, 2009 | 2001 Chrysler Town & Country

1 Answer

Liftgate will not open


There is a plastic pin that hold the handle linkage together inside the door panel.

I would take off the inside cover to the back door and check the linkage. The correct part is probably at the dealer for purchase.

Mar 18, 2009 | 2004 Ford Freestar

Not finding what you are looking for?
2002 Kia Sedona Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

yadayada
yadayada

Level 3 Expert

77169 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...