Question about 2000 Honda Accord

2 Answers

How do i take clutch fork out. trying to

How do i take clutch fork out. trying to seperate tranny from motor 2000 honda accord 4 cly

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 691 Answers

Im assuming its 5speed, just remove the cables/line, no need to remove the clutch fork out to separate the tranny from the motor, clutch fork only work the throw-out bearing, it stay with the transmission; it little stubborn sometime for both to seperate from one another. just make sure the tranny is well balance and not hanging from the motor while trying separate the two. it will be very difficult trying to pull the tranny away from the motor if its not on the correct level and height and must not have no weight on the transmission shaft. You have to slide the tranny straight out and level from the flywheel, tranny shaft has to come out straight and same way when reinstall.

Posted on Sep 24, 2009

Testimonial: "thank u very much now i know the fork is not holding ."

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 163 Answers

You seperate the bellhousing from the engine not the transmission from the bellhousing... Sorry...You need to go one housing further forward.

Posted on Sep 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 ford 4 x 4 6 cly tranny stuck in 4th ,,,,,,,help


If it is standard, could be a bad clutch or clutch cylinder, sounds like a bad slave cylinder on the clutch. Check the clutch fluid level. Should be near the brake fluid and should be the same fluid as well.

Sep 20, 2014 | Cars & Trucks

1 Answer

Does an automatic transmission have a countershaft?


Depends on the gearbox design. Aisin(Toyota) troque converter automatic trannys are generally epicyclic (planetary), so are (GM and Ford) TC automatics. And I have heard Honda uses a countershaft design for its automatic trannys. Dual clutch automatic trannys have in general countershaft design as opposed to TC automatics.

Oct 05, 2012 | 2000 Honda Accord

2 Answers

How do I remove tranny and clutch seems stuck on the engine 2000 hundai elantra manuel I can get it off about a half inch and it stops


the clutch is a pull type, not a push type, to remove the trans you have to remove the release fork lever, to do that fist remove the clutch slave cylinder, then remove the 14mm nut tha holds the fork arm, then you can remove the trans, however reassembly is a whole nother complicated story.

Nov 18, 2009 | 2000 Hyundai Elantra

2 Answers

2000 honda accord auto


ckeck the level of the Auto Transmission fluid on the Dipstick. If it is low ADD some.Regards, DT

Aug 29, 2009 | 2000 Honda Accord

2 Answers

Manual clutch replacement problems


has a clip behind it or 2 [1 each side]
if its a wire clip release it if its
if its 2 just pull

Jul 20, 2009 | 2000 Hyundai Elantra

1 Answer

1985 Honda Accord clutch slip and other advice


try adjusting clutch first.if it still slips in 4th and 5th.then you have to change clutch pressure plate and clutch release bearing and check condition of fork.

Jun 07, 2009 | 1985 Honda Accord

2 Answers

2000 Accord Transmission Problem


Hello mew2149...Honda had a recall on your transmission for several failures, the one you describe being among them. If you have 194k with no problems then you are one of few. Honda extended warranty to help owners absorb the cost. http://world.honda.com/news/2002/4020920.html A good transmission shop will be able to evaluate your problem better with pressure tests. The torque converter could be bypassing fluid, pump weak, clutch pack worn...etc. Good luck...i hope this helps.

Jun 04, 2009 | 2000 Honda Accord

1 Answer

Oil leak


When you buy a valve cover set, those seals come in the set.

Jul 11, 2008 | 2000 Dodge Stratus

Not finding what you are looking for?
2000 Honda Accord Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...