Question about 1987 Saab 900

1 Answer

No power to ignition - 1987 Saab 900

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 299 Answers

Sounds like a blown fuse or fusible link

Posted on Sep 24, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

No power to ems relay,ignition amplifier,or ignition coil . fully charged battery with 12.66 volts coming out of ignition on relay

Check the power at the relay at right front fuse box if no power check back wire as it runs to the relays beside the radiator.

Mar 24, 2014 | 1994 Jaguar XJ6

1 Answer

No power to ignition

your power runs from the ignition to the solenoid. if there's no power at the ignition, you need to check for power to the ignition, and if there's power you need an ignition switch. If you don't then you might need PCM

Jul 13, 2013 | 1989 Ford F 150

1 Answer

Lost power to ignition,power window's and heater.

look for the fusible link located from battery to starter or from the starter to the ignition.

May 28, 2013 | Cars & Trucks

1 Answer

Power to starter wire with ignition off

main wire supposed to have power. ignition feeds the solenoid engage wire when ignition is turned on

Jan 17, 2013 | 2004 GMC Envoy

1 Answer

2005 cavalier 2.2 /no spark

check ignition coil see if its getting battery power check black and pink ignition wire going to ignition coil.if you not getting power check the 20AMP ignition fuse.if power going to ignition coil, problem could be bad ignition coil or bad ignition module or pcm problems, best have vechicle code scan for pcm fault or crankshaft position sensor or ignition module fault.

Sep 29, 2012 | Chevrolet Cavalier Cars & Trucks

1 Answer

Were is ignition control module

There is no actual ignition control mudule in this vehicle, the ignition signal from the ECM is sent to and amplified by the power transistor.

Hiope this information is helpful...

The ignition signal from the ECM is sent to and amplified by the power transistor. The power transistor turns on and off the ignition coil primary circuit. This on-off operation induces the proper high voltage in the coil secondary circuit.

Sep 18, 2011 | 2002 Nissan Sentra

1 Answer

No power to the ignition but the battery is hot

Common for the ignition switch it self to go bad after a few years. You can buy a replacement ignition switch at Auto Zone and they will have the step by step instructions for you to get the job done.
Thank you for using fixya and good luck

Jun 19, 2010 | 2000 Chevrolet S-10

1 Answer

No ignition power

You blew the fuse, replace it and get a ignition tumbler back in it.

Feb 02, 2010 | 1989 Ford F 150

1 Answer

Is there a inline fuse from the ignition switch to the ignition coil?

no sir
not from the switch to the coil.
the coil does not get power from the switch.
the switch turns relays on that powers the coils.
but there is an ignition fuse.
the ignition switch turns on power relays from the battery that powers the ignition system.
the ignition system fuse is in the fuse box.

hope this helps
thank you

Jul 29, 2009 | 1995 Ford Explorer

2 Answers

1996 ignition switch-what wires to check power on

ignition switch may be worn or a loose exciter wire [to starter] thats the small terminal on starter motor you can bridge it to the posative [power] on the starter it should start!
if it does start just work back from there to ignition look for broken or loosse connection
if that all is ok it will need ignition switch

Jul 18, 2009 | 1996 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers


Level 3 Expert

76630 Answers


Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides