Question about 2001 Chevrolet Camaro

1 Answer

Instaled new intake manifold gasket now it back fires when eccelerating

Posted by on

  • Richard Scordino May 11, 2010

    Likely the timing is off. or you have crossed #5&7 ignition wires.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 3,433 Answers

Place your hand over the pcv hole in the calve cover and note if you feel vacuum. If so, you have a intake gasket leakinf or out of place.

Posted on Sep 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i REPLACE INTAKE MANIFOLD GASKET ON 1989 BRONCO ii


Unbolt the Intake Manifold, install the new gaskets and bolt it back in place. My best advice to you is go to a auto parts store and buy a manual as it will tell you exactly how to do it.

Feb 02, 2015 | 1989 Ford Bronco II

Tip

How to remove/replace the Valve Cover Gaskets on a New Beetle car?


Replace the valve cover gasket if the valve cover gaskets are leaking or if they're worn. The procedure is as follows:--
1) First of all let the motor cool down if the car was recently driven. Then remove the air intake boot.The air intake boot ios attached to the engine's throttle body.
2) Carefully disconnect the throttle cable , hoses and electrical connectors located on the upper intake manifold.
3) Then disconnect the hard pipe that is connected to the EGR (exhaust gas recirculation) valve.
4) The EGR valve is located beneath the upper intake manifold.
5) Then remove the bolts from both the upper intake manifold and the manifold support bracket.
6) Now the upper intake main fold and lower intake manifold both have got loose as you removed the nut.
7) After that remove the upper intake manifold from the lower intake manifold. Carefully place clean rags over the intake runners to prevent anything from falling into the intake system.
8) Then you will have to disconnect the crank case breather valve on the valve cover.
9) Then remove the bolts from the valve cover and remove the reinforcing straps.
10) Then remove the camshaft belt cover and the dust shield from the back of the camshaft sprocket.
11) Now carefully remove the valve cover. Properly clean the old gasket material with gasket remover.
12) You can install a new gasket in the reverse procedure of removal.


This will help. good luck.

on Mar 09, 2010 | Volkswagen Beetle Cars & Trucks

Tip

Stalling and running rough - Hyundai Elantra - 2001-05


The Hyundai Elantra 2001 - 2005, 2.0 L engine is noted for this problem. It will lack power on acceleration and run rough and stall while driving. The engine light will come on for misfire codes. This problem is caused by a vaccum leak at the intake manifold gasket. The gasket is broken and needs to be replaced.
To replace the intake gasket with a new one, remove the 12m nuts holding the intake to the cylinder head. Then pry back( note: you do not have to completely remove the intake manifold here) the intake manifold to gain excess to remove the old gasket. Remove any excess gasket and clean with brake cleans the surface area of the intake. Install the new intake gasket on to the head and carefully install intake on to cylinder head studs. Tighten up nuts gradually and evenly to 15-20 ft.lbs.

Steve

on Jan 14, 2010 | Hyundai Elantra Cars & Trucks

1 Answer

How to fix oil leaks in chevy ss impala 1996



Instructions

1. Removal

Unscrew the bolt that holds the negative connection to the Impala's battery. Set this bolt aside for later use.

Remove the engine cover to access the intake manifold and manifold gasket. Disconnect the throttle body inlet duct from the engine.

Twist off the radiator cap to allow draining of the coolant to flow more smoothly. Place an empty container beneath the radiator's drain plug, and remove this plug. Allow all of the engine coolant to drain into the empty container. Replace the drain plug once you are finished.

Tag all of the electrical wiring and hoses before removing so that reconnection is precise to factory settings. Remove these parts, individually, from the intake manifold.

Loosen the bolts that hold the intake manifold to the Impala's engine block. Lift the intake manifold from the block once all bolts have been completely removed.

Use the flat-head screwdriver to pry the old intake manifold gasket from the engine block. Discard this part once you have removed it.

Clean the engine block thoroughly with the engine degreaser and linen cloth. If necessary, use a gasket scraper to remove excess buildup and grime.

2. Installation

  • Coat the top and bottom of the new intake manifold gasket with a chemical sealer so that it bonds to the engine block securely. Position this new manifold gasket so that it lines up perfectly with the cylinder ports of the Impala's engine block.

Place the old intake manifold on top of the newly-installed manifold gasket until it aligns with all of the holes of the cylinder flanges and manifold gasket.

Attach all of the bolts with your hand to the manifold. Once all bolts have been positioned, use a torque wrench and apply 15 foot-pounds of pressure to the bolts to secure the manifold into place.

Reconnect all of the necessary hoses and electrical wiring to the intake. Pour the engine coolant back into the radiator.

Reattach the engine cover on top of the intake manifold and engine block. Start the Impala's engine and check for any leaks around the new intake manifold gasket.

Jul 08, 2012 | 1996 Chevrolet Impala SS

2 Answers

What's the difference between a blown head gasket and a blown intake gasket?


The head gasket goes between the block and the head, and seals the combustion process, and cooling water, and (if oil is pumped obove the heads to valve components) oil pressure.

Intake gaskets seal between the intake manifold and the head, and seal against intake vacuum, and in many cases, coolant.

A badly blown head gasket will so destroy compression in the cylinder that you can hear uneven cranking as that cylinder comes up on compression, kind of a “whir, whir, WHIR, whir, whir, WHIR, whir” with the capitalized whir being the engine spinning much faster due to no compression holding the starter back.

You will never be able to hear a problem with an intake manifold gasket until the engine actually starts to fire and/or run.

Aug 10, 2010 | 1994 Pontiac Grand Am

2 Answers

Need to replace the intake manifold


3.8L Engine (most common) Upper Intake Manifold To Remove:
  1. Drain the cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable.
    • Fuel injector sight shield.
    • Air cleaner intake duct.
    • Right spark plug wires from the ignition control module and reposition.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Fuel rail assembly.
    • Brake booster hose from the vacuum source manifold in the upper intake manifold.
    • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
    • Throttle body support bracket upper bolt.
  5. Disconnect the electrical connectors from the following:
    • EVAP purge solenoid
    • Throttle Position (T/P) sensor
    • Idle Air Control (IAC) valve
    • Manifold Absolute Pressure (MAP) sensor
    • Mass Air Flow (MAF) sensor
    • EVAP purge solenoid vacuum line from the throttle body.
    • Accelerator and the cruise control cables with the bracket from the throttle body.
  6. Remove or disconnect the following:
    • Upper intake manifold bolts and stud.
    • Clean the upper intake manifold bolt threads.
  7. Remove or disconnect the following:
    • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
    • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
  8. If the upper intake manifold is being replaced, remove the following:
    • Throttle body assembly.
    • Manifold Absolute Pressure (MAP) sensor.
    • Positive Crankcase Ventilation (PCV) valve.
    • Vacuum source manifold.
Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

To Install:
  1. If the manifold was replaced, install or connect the following:
    • Vacuum source manifold.
    • Positive Crankcase Ventilation (PCV) valve.
    • Manifold Absolute Pressure (MAP) sensor.
    • Throttle body assembly.
    • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
  2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
  3. Install or connect the following:
    • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
    • Accelerator and the cruise control cables with the bracket to the throttle body.
    • EVAP purge solenoid vacuum line to the throttle body.
  4. Connect the electrical connectors to the following:
    • Mass Air Flow (MAF) sensor
    • Manifold Absolute Pressure (MAP) sensor
    • Idle Air Control (IAC) valve
    • Throttle Position (T/P) sensor
    • EVAP purge solenoid
  5. Install or connect the following:
    • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
    • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
    • Brake booster hose to the vacuum source manifold.
    • Fuel rail assembly.
    • Right spark plug wires.
    • Air cleaner intake duct.
    • Fuel injector sight shield.
  6. Connect the negative battery cable.
  7. Fill the cooling system.
  8. Inspect for fluid or vacuum leaks.
Lower Intake Manifold (W/O Supercharger) To Remove:
  1. Remove or disconnect the following:
    • Upper intake manifold.
    • Generator brace.
    • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
    • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
    • Radiator inlet hose from the water outlet housing.
    • ECT sensor electrical connector.
    • Right upper engine mount strut bracket.
    • Generator brace bracket bolts.
    • Generator brace bracket.
    • Lower intake manifold bolts.
    • Lower intake manifold.
    • Lower intake manifold seals.
    • Lower intake manifold gaskets.
  2. If replacing the lower intake manifold, Remove or disconnect:
    • Water outlet housing bolt and stud
    • Water outlet housing
    • Gasket and the thermostat.
    • ECT sensor.
  3. Inspect the flatness of inlet flanges.
  4. Clean the intake manifold mating surfaces.
  5. Clean the intake manifold bolts and bolt holes of adhesive compound.
To Install:
  1. If removed, install the ECT sensor.
    • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
  2. If removed, install the thermostat, the gasket, and the water outlet housing.
  3. If removed, install the water outlet housing bolt and the stud.
    • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
  4. Install or connect the following:
    • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
    • Lower intake manifold seals.
    • Lower intake manifold.
    • Lower intake manifold bolts.
    NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
  5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

  6. Install or connect the following:
    • Generator brace bracket.
    • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
    • Right upper engine mount strut bracket.
    • ECT sensor electrical connector.
    • Radiator inlet hose to the water outlet housing.
    • EGR outlet pipe to the lower intake manifold.
    • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
    • Drive belt tensioner.
    • Generator brace.
    • Upper intake manifold.
  7. Inspect for leaks.
Lower Intake Manifold (W/ Supercharger) To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the supercharger.
  4. Remove the thermostat housing.
  5. Remove the EGR pipe at the intake manifold.
  6. Disconnect the electrical connection at the temperature sensor.
  7. Remove the intake manifold and gaskets.
NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:
  1. Clean the gasket sealing surfaces.
  2. Install the intake manifold gaskets.
  3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
  4. Install the electrical connector to the temperature sensor.
  5. Install the EGR pipe to the intake manifold.
  6. Install the thermostat housing.
  7. Install the supercharger.
  8. Fill the cooling system.
  9. Connect the negative battery cable.

Aug 05, 2010 | 1997 Pontiac Grand Prix

2 Answers

My 1996 chevy suburban runs rough with no engine lights it has a 350 i just had the intake manifold gasket done


spray carburetor cleaner to the surrounding gaskets of the intake manifold while the engine is running.. If the idle increases upon spraying the cleaner the intake is leaking

Mar 10, 2010 | Chevrolet Suburban 1500 Cars & Trucks

2 Answers

HOW TO REPLACE INTAKE MANIFOLD ON A LINCOLN


answer , very carefully ...

drain coolant , remove and mark all vacuum lines , make a schematic to diagram your hose routing, disconnect and plug all fuel lines, remove distributor and mark location of rotor, disconnect battery, remove any necessary cables, brackets and or accesseries, remove intake mounting bolts, note length of bolts and reference location, pry up on intake , remove intake, scrape old gasket off , must be very clean to reinstall new gasket or you will cause a leak..

Nov 02, 2009 | 1999 Lincoln Town Car

1 Answer

Intake manifold gasket / replace


3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Sep 11, 2009 | 1999 Buick Regal

1 Answer

Intake manifold gasket change


You do not have the dist. in correct or plug wires are crossed. Please check wires 18436572 is firing order.

Jan 10, 2009 | 1993 Chevrolet Caprice

Not finding what you are looking for?
2001 Chevrolet Camaro Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...