Question about 2004 Ford Focus

Open Question

I have a ford 2000 TDCi and it keeps going in to limp mode. Fault cods are P2452 and P2453 an ideas?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22219 Answers

SOURCE: how to remove a turbo charger from a ford focus tdci

better left to mechanic not easy to do

Posted on Nov 12, 2008

Ad
  • 1201 Answers

SOURCE: ford focus 1.8 tdci i have the fault codes p2263

It means the turbo/supercharge boost system is malfunctioning.
Have it checked.

Posted on Aug 29, 2009

  • 750 Answers

SOURCE: Holden rodeo 99 3.2v6 4l30e code 82 and going into limp mode

the tcm may be faulty or has a loose ground, try swaping in another if you can get one borrowed or a cheap used one from a salvage unit

Posted on Oct 30, 2009

  • 246 Answers

SOURCE: fault codes p1211 and p0251 keeps putting my van

Fuel injection circut malfunction.
How many cylinders

Posted on Jan 03, 2010

ajarema
  • 404 Answers

SOURCE: 06 ford focus 1.6 tdci, fault code p2585 showing.

There are only p258 a-f codes and there is no p2585, anyway it is either vacuum pump problem, normally solved by checking or replacing the wiring or it is torque management system and it is also related to wiring. In both you need to get a proper reading of code again and than check wires after that get the test done again.

Posted on Jan 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2004 rx8 when you start it it runs great until it warms up & goes into limp mode. Turn it off & back on most of the time its fine for about a mile then back into limp mode. Please HELP


first option is to have the fault codes read
limp mode is activated by both the engine and transmission sensors
going to limp mode so quick could be an overheating problem , transmission vss/tcm problem or ECM fault
by reading the fault codes , you will get a better idea of the problem

Mar 09, 2017 | Cars & Trucks

1 Answer

Focus 2.0 tdci lack power limp mode 3000 rpm yr 2005


Try a computer reset disconnect batterie and wait 2 minutes

Oct 13, 2015 | Cars & Trucks

1 Answer

Ford mondeo faults


the flashing orange light is the glowplug light that telling you there is a engine managment problem. you need to get the fault code out of the engine control module with a obd code reader to determine the cause but the common cause of the flashing glow plug warning is a air leak after the turbo charger

Jun 04, 2017 | 2006 Ford Mondeo 1.8

1 Answer

Ford mondeo faults


Get the codes read.it will tell you whats wrong. That is why it is on.

Jun 04, 2017 | 2006 Ford Mondeo 1.8

1 Answer

2005 focus 1.6 limp mode problem and P2100 code


Try clearing the code from the computer. If it returns again, the second hand one could be bad also! Some codes are what they call a hard code, that stays in the computer memory, and will think that the problem wasn't repaired (even though the part was replaced). Till the code is cleared from the memory, the vehicle will return to a limp mode untill the problem is resolved!!

Apr 18, 2014 | 2005 Ford Focus 1.6

1 Answer

Ford Mondeo tdci fault code says speed sensor causing loss of power?


replace the speed sensor and rerun the fault codes as this unit may be restricting the engine operation and put it in limp mode.

Apr 12, 2014 | 2004 Ford GT

1 Answer

Failsafe keeps appearing


take it to jaguar and have the software checked and any fault codes removed ,

Apr 30, 2010 | 2000 Jaguar S-Type

1 Answer

Fault codes p1211 and p0251 keeps putting my van


Fuel injection circut malfunction.
How many cylinders

Jan 02, 2010 | 2000 Ford F350 Super Duty Super Cab

1 Answer

Mondeo tdci


hi there, you will need a diagnostic check carried out to locate the exact fault, most garages have the equipment to carry out these checks so you won't need to visit your ford agent, a common fault on the engines is the camshaft sensor these cost around £20 and are very easy to replace, however once you have it tested you will now your exact fault, hope this helps

Oct 23, 2008 | 2000 Ford Focus

Not finding what you are looking for?
2004 Ford Focus Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...