Question about 1989 Pontiac Bonneville

1 Answer

How can one tell if the rear wheel bearing and hub assembly need replacing.. Mine has no play or noise issues. The vehicle has 220kms.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 299 Answers

If its not making noise and its not loose its ok

Posted on Sep 24, 2009

Testimonial: "that was quick and painless thx so much!"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the rear wheel hub on a 2003 Kia sedona. All I can find is directions on front not back.


Wheel Bearings

Print
Adjustment

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cover Cotter pin Lock nut cover
  3. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm).
Removal & Installation

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cap Cotter pin Lock nut cover Lock nut Wheel bearing retainer washer and the outer wheel bearing Hub assembly Grease seal Inner wheel bearing
  3. Clean and inspect the wheel bearings and races for unusual wear or damage. Replace parts as necessary.
To install:
  1. Pack the wheel bearings with grease for assembly.
  2. Install or connect the following:

    Inner wheel bearing Grease seal Hub assembly Lock nut. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm). Lock nut cover Cotter pin Hub cap Brake drum Rear wheel

Apr 03, 2015 | 2003 Kia Sedona

1 Answer

Noise from the rear of the 2012 impala while driving. The faster you go the louder the noise.


need new wheel bearing,it is actually called hub bearing,need to change the hub assembly,do yourself a favor,either by ac delco,or timken brand any thing else is garbage

Mar 13, 2014 | Chevrolet Impala Cars & Trucks

1 Answer

The rear wheel bearings on my 1998 Honda Civic Aerodeck are rumbling and I need to know how to replace them or regrease and is it a DIY or garage job


Your vehicle is equipped with sealed bearings that are pressed into the hub assembly. If your rear wheel bearings are making noise, you must replace the entire bearing and hub assembly (they cannot be greased).

To replace it, raise and support the vehicle and remove the tire and wheel assembly. Remove the brake drum. Remove the bearing cap, the spring nut and the axle washer. Remove the hub assembly and hub seal. The new hub assembly should come with a new hub seal installed. (See first picture below)

TIP: The brake drum has threaded holes in its face where an 8mm bolt can be inserted to help "push" the drum off of the hub assembly - they can get really stuck. (See second picture below)


dttech_22.jpg


dttech_90.gif

May 22, 2011 | Honda Civic Cars & Trucks

4 Answers

I have a loud humming sound coming from what sounds like the front right wheel. I jacked it up and checked the wheel for play. and there is no movement. but the humming is getting worse. its not the...


Unfortunately you do not always get "play" in the bearing and they are unserviceable. Replace the entire unit. Here are the instructions for replacement. They bolt into place making it pretty easy to do. Soak the CV shaft which pertrudes from the hub where the nut goes with a good rust penetrant to ease in removal.


Removal & Installation


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Front wheel Wheel Speed Sensor (WSS) electrical connector Brake caliper and bracket Rotor Driveshaft nut
  3. Install a front hub removal tool to the wheel bearing/hub assembly with three wheel nuts. Use the tool to push the driveshaft out of the wheel bearing/hub.
  4. Remove the wheel bearing/hub assembly and discard the bolts.

To install:
  1. Install or connect the following:

    Wheel bearing/hub assembly using new bolts and torque them to 96 ft. lbs. (130 Nm) New drive shaft nut and torque it to 118 ft. lbs. (160 Nm) Brake rotor Front caliper with the bracket WSS electrical connector Front wheel

May 16, 2011 | 2003 Chevrolet Impala

1 Answer

How to replace rear wheel bearings on a 2000 cougar?


Hi,welcome to fixya.


The rear wheel bearings are not adjustable. If the bearings make noise or become loose, they must be replaced.

Removal & Installation

With Drum Brakes

NOTE The wheel bearings are contained within the wheel hub and must be replaced as an assembly.

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Remove the anti-lock sensor retaining bolt and remove the sensor.
  5. Remove the brake drum retainer and the brake drum.
  6. Remove the hub retaining nut dust cover.
    NOTE Do not use an impact gun to remove the hub retainer nut.


    0996b43f80232353.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Using suitable tools loosen and . . .


    0996b43f80232351.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. . . . remove the hub retaining nut dust cover
  7. Remove the wheel hub retainer nut.

    0996b43f8023234f.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Using suitable tools, loosen and . . .


    0996b43f80232352.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. . . . remove the hub retaining nut
  8. Slide the hub and bearing assembly off of the spindle.

    0996b43f80232350.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Carefully slide the hub and bearing assembly off of the spindle

To install:
  1. Reinstall the hub and bearing assembly to the spindle.
  2. Reinstall the hub retainer nut. Tighten the retainer nut to 170-192 ft. lbs. (230-260 Nm).
    WARNING Do not use an impact gun to tighten the hub retainer nut, otherwise the bearings may be damaged.
  3. Install the hub retaining nut dust cover.
  4. Reinstall the brake drum.
  5. Check the brake shoes for proper adjustment.
  6. Reinstall the anti-lock sensor and the retaining bolt. Tighten the retaining bolt to 7-8 ft. lbs. (9-11 Nm).
  7. Reinstall the wheel and tire assembly. Tighten the wheel nuts to 62 ft. lbs. (85 Nm).
  8. Lower the vehicle until the wheels are supporting the vehicles weight. This will properly load the suspension.
  9. Tighten the spindle-to-control arm bolt to 52-79 ft. lbs. (70-98 Nm).
  10. Tighten the tie rod-to-spindle bolt to 75-102 ft. lbs. (102-135 Nm).
  11. Finish lowering the vehicle.
Road test the vehicle and check for proper operation.
Thank You for using fixya........iluv2fish........Ray........

Jul 16, 2010 | 2000 Mercury Cougar

1 Answer

Need to know the torque specs for a rear wheel bearing on a 1999 monte carlo?


Hub & Bearing 3.8L engine Removal & Installation To Remove:
Hub and bearing assembly mounting 88008g39.gif

All W-body cars are equipped with sealed hub and bearing assemblies. The hub and bearing assemblies are not serviceable. If the assembly is damaged, the complete unit must be replaced.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle with jackstands.
  3. Remove the rear wheel and tire assembly.
  4. If equipped with rear disc brakes, remove the caliper, bracket and rotor.
  5. If equipped with rear drum brakes, remove the brake hose bracket and drum.
  6. If equipped, detach the ABS electrical harness.
  7. Unfasten the four hub/bearing-to-knuckle attaching bolts, then remove the hub/bearing assembly.
To Install:
  1. Install the hub/bearing assembly onto the knuckle. Install the four attaching bolts and tighten to 52 ft. lbs. (70 Nm).
  2. If equipped attach the ABS electrical harness.
  3. Install the rotor, caliper and bracket or drum and bracket, as applicable.
  4. Install the wheel and tire assembly.
  5. Carefully lower the vehicle.
  6. Connect the negative battery cable.

Jul 15, 2010 | 1999 Chevrolet Monte Carlo

2 Answers

How to replace rear wheel bearings


don't have topaz. maybe escort will help guide you.

Section 04-02: Suspension and Wheel Hubs, Rear 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Wheel Bearing and Hub Assembly NOTE: Wheel bearings are not serviceable and should therefore be replaced as an assembly with the wheel hub (1104).

Removal
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
  1. Remove the hub grease cap (1131) from the wheel hub.
  1. If equipped with disc brakes, remove the rear disc brake caliper (2552) and rear disc brake rotor (2C026). Refer to Section 06-04 for the removal procedure.
  1. If equipped with drum brakes, remove the two brake drum screws and the brake drum (1126).
  1. Unstake the rear axle wheel hub retainer (4B477) securing the wheel hub to the rear wheel spindle (4A013). Remove and discard the rear axle wheel hub retainer.
  2. Remove the wheel hub from the rear wheel spindle.

Feb 06, 2010 | 1990 Mercury Topaz

2 Answers

Where wheel speed sensor is located on 2001 pontiac grand am se


2001 Pontiac Grand Am 2.4L SFI DOHC 4cyl

Vehicle Speed Sensor - Location:
The speed sensors are built right into the wheel bearings of your vehicle, at the front and rear locations. They work both with the anti-lock brakes and with the traction control systems on the vehicle.

Removal & Installation
Front
The front wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Front Suspension for service procedures.
Rear
The rear wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Rear Suspension for service procedures.

I hope help you with this (remember rated this help) Have a nice day, good luck.

Sep 23, 2009 | 2001 Pontiac Grand Am SE

3 Answers

I have front end vibration that is not caused by alignment. New tires on all four wheels but still have alot of front end vibration. Car is a 2004 Hyundai Tiburon.


just checked this out a while ago:



Wheel Hub Assemblies: Systems and Diagnosis of Worn Hub Assemblies & Bearings
Front wheel hub assemblies and bearings control the position of, and reduce the resistance of, vehicle wheels in contact with the pavement. When they fail, front wheels may not be kept in position and vibration and noise usually develop. Symptoms that normally develop as a result of these worn parts include:
  • A humming, rumbling or growling noise which increases with acceleration or as the vehicles turns
  • Vibration felt in the steering wheel, which changes with vehicle speed or as the vehicle turns
  • Looseness or excessive play in the steering wheel (especially while driving over rough road surfaces)
  • A loud, constant grinding noise when driving the vehicle (heard in the most severe cases of a wheel bearing failure)
  • Pulling to one side when braking.
  • Roughness - with the vehicle of the ground, roughness or vibration when rotating the wheel
  • Looseness - with the vehicle off the ground, looseness when wiggling the wheel back and forth (Looseness may also indicate a worn ball joint)
  • Excessive brake pedal play can also indicate sloppy or excessively loose wheel bearings
  • ABS failure in the system may be related to failure of the ABS sensor in the hub assembly or the internal sensor in the wheel bearing

Dec 22, 2008 | Hyundai Tiburon Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...