Question about 1984 Ford Mustang

1 Answer

Bleed the brake lines

How do you bleed the brake lines in a 84 ford mustang gt

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 96 Answers

Start at the passenger rear tire, have someone PUMP up brakes and hold pressure on them, release pressure by locating small bleeder screw, loosen screw 1/4 turn, brake fluid/air should come out, after brake petal reaches floor tighten bleeder, repeat process until only brake fluid comes out. go to driver side rear repeat, go to pass. side front repeat, go to driver side front repeat, after each bleeding make sure you check brake fluid in reservoir.

Posted on Sep 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do you have to bleed every wheels brake or just at master cylander in a 2001 mustang


You have to bleed all four corners on all
vehicles every 2 years

Brakes have to come apart every 9 months
or one year at the most, to remove rust,lube
all sliding parts & whatever other service is needed

Feb 25, 2013 | 2001 Ford Mustang

1 Answer

How do you bleed rack and pinion on a 1993 mustang gt


i don't think you can bleed rack and pinion it is a loop systeminone way and out the other.

Sep 18, 2012 | 1983 Ford Mustang Hatchback

1 Answer

After bleeding the brakes on my 84 mustang I noticed that one of the bleeder screws was not tight and fluid spilled out on the driveway. I tightened the screw and re-bleed the brakes but, the peddle goes...


Yes and No...Replacing the master cylinder is a good idea, however, giving the vehicle that much pressure with old lines attached may blow out the old rusted lines. If you are going to replace the master cylinder, you may just want to replace the brake lines as well.

Aug 29, 2011 | Ford Mustang Cars & Trucks

1 Answer

Brake line size 1986 mustang GT 5.0. 3/16 or 1/4


rear brake lines 3/16" front brake line 1/4"

Apr 17, 2011 | 1986 Ford Mustang

3 Answers

Have a 1996 ford mustang GT There's a switch I don't know what is


are the lines like /// or wavy?? could be the car had factory fog lights /// or could be headlight defroster (didn't know it was available on a stang)

Feb 04, 2010 | 1996 Ford Mustang

1 Answer

How to replace the front brake hose on an 84 ford


should be a bolt where the hose enters the front caliper. just unhook and replace with new one. Be forewarned. When you change out the lines, you need to bleed the brakes as well.

Oct 07, 2009 | Ford Bronco II Cars & Trucks

1 Answer

84 Mustang AC Problem


jumper the low pressure switch on the Acc. if the AC runs, check the charge on the A/C if the charge is correct. replace the LPS.

Aug 18, 2009 | 1984 Ford Mustang

2 Answers

97 mustang gt running threw rear brake pads


how many miles are u getting on a set of brake pads before they wear out? Have u flushed out the lines? Contaminated brake fluid can ruin the calipers, causing internal corrosion which in turn causes the caliper to drag and burn out the pads prematurely. The strange thing w/ this theory, is the fact that it's just one wheel. I would try bleeding all the lines though, to make sure u have bled all old fluid, and replaced it w/ new. Has the mustang ever been in an accident? Just wondering if caliper mounting bracket is tweeked, or some other component that the brake system is mounted to. Let me know if this is any help, and if not, if u have any more clues that might help figure this out. Good Luck

Nov 07, 2008 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

2001 Mustang GT rear brake job


yep this is a two man job, onece you get air in the lines is better to do all four, my has abs and i was able to do it, but next time don't take anylines lose just turn the piston clockwise and you should be able to push it in.

Sep 11, 2008 | 2001 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

326 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...