Question about 2000 Mitsubishi Eclipse

1 Answer

How to adjust the head lights on my 2000 eclipse

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,986 Answers

You should have two plastic nuts on each headlamp assembly, one will be for your high beams and one will be for your low beams.

The nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail (might see holes in your rail above the headlamp unit where the screws are hidden)

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 mitsubishi eclipse how do i adjust the headlight aim if the light shoots too high?


at the back of the light assembly you will find 3 screws or knobs situated around the reflector . By screwing up of off the head light will move up down or sideways depending which screws you adjust

Nov 22, 2013 | Cars & Trucks

1 Answer

2000 mitsubish eclipse overheating. replaced radiator, repleased temperature gauage. One fan kicks on, the other doesn't.


i would suggest you get the head gasket checked you can get a kit from motor factors which does gas test in header tank if blue liquid changes colour to brown you need to replace head gasket

Oct 16, 2011 | 2000 Mitsubishi Eclipse

1 Answer

I have a 2000 Mitsubishi Eclipse GT that ticks pretty loud until it warms up. A few people have told me to adjust the valves. What are the specs on adjusting them?


I think the best thing to do is just try a lighter weight fully synthetic oil in it. What you're hearing is the valves sticking in oil that is not bleeding down fast enough while it is cold.

Nov 08, 2010 | 2000 Mitsubishi Eclipse

1 Answer

Deei just changed my head gaskets on my v-6 eclipse. now i have a oil leak and i have smoking. is it because of a bad seal, on my head gasket


could be, the first thing i would do is get the cyclinder head bolts torqued to right setting.Provided the cyclinder head is not warped ie the engine did not overheat before gasket was replaced?All heads have to be rechecked/retorqued after about 1000mls anyway,adrian,,,,,,,,,,,,

Aug 31, 2010 | 2000 Mitsubishi Eclipse

1 Answer

Dash lights dont work on 2000 mitsubishe eclipse


change out the water pump that should solve your problem for over heating.

Mar 17, 2010 | 2000 Mitsubishi Eclipse

1 Answer

Panel lights


you unplugged the wiring for the panel lights or blew the fuse

Mar 03, 2010 | 2000 Mitsubishi Eclipse

1 Answer

Where is the back up light switch mine went out and i need to replace it. its on a 2000 mitsubishi eclipse


The reverse light switch will be on your transmission, mst likely near your shift linkage. It will look like large fitting with a hex head for a wrench to fit on and two wires with a plug coming out of the top. When you take this out, it will have a metal ball on the end that was in the transmission. Before removing it though, you may want to put a jumper wire across the two wires that plug into it and check the reverse lights. If they come on then, it is the switch, if not, you have a problem somewhere else. Let me know if this helps :)

May 11, 2009 | 2000 Mitsubishi Eclipse

1 Answer

Thick smoke out of tail pipe


likely a blown head gasket is the cause.

Apr 14, 2009 | 2000 Mitsubishi Eclipse

1 Answer

Dim headlights


check to see if a wire is grounded or the connection at the base of your head lights. Try pushing or wiggling around the wires.

Aug 06, 2008 | 2000 Mitsubishi Eclipse

Not finding what you are looking for?
2000 Mitsubishi Eclipse Logo

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...