Question about 2003 Jaguar S-Type

1 Answer

Burnt out bulb. How to open fixture for replacement?

Posted by on

  • Raygin
    Raygin May 11, 2010

    what bulb and where ??

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Collin fan do not come on

Posted on Sep 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the tail light fixture to replace a burnt out bulb on my 2002 VW cabrio


Open the back latch, look at the taillight housing you will either see regular phelps heads or York heads. Can you send me a picture.

Mar 03, 2013 | 2002 Volkswagen Cabrio

1 Answer

Only front left signal flashes when hazard lights or on, does get a dash indication light but only the left one; turn signal lights work but sometimes stays on solid (doesnt blink) on the dash. is this a...


I would check each bulb on the side with the most issue, usually when one light goes out,for whatever reason, the system is designed to malfuntion signalling an alert to the operator..with the lights and hazards on, check each fixture for good operation while opening up each light take the bulbs out and inspect them for defects, replace with new if anything is doubtful be careful with the bulb grease dont get any on the contact points because it will get hot and cause small issues.. do each light at a time until all 4 are working fix any defects to include burnt fixtures and broken wires and make sure all grounds are good also, these connectors are notorious for rust and corrosion so clean them well before reinstalling , I use the same bulbs in my 92 dodge so i am aware of the type..good luck..

Jan 13, 2013 | 2004 Ford Explorer

1 Answer

Need to change rear brake light bulb on a 2000_L sedan. Owners manual addresses only the turn signal bulb change proceedure. The brake light fixture is flat not round.


there is an access cover in the trunk.Open that and just pull the bulb fixture out replace the bulb and place back in the hole.

Apr 07, 2012 | Saturn Cars & Trucks

2 Answers

What do I need to do if my overhead dome light does not work and the bulb has been changed often even though the bulb was not burnt out. I cannot get it to work at any of the 3 positions more than 4 days.


remove the lens cover. take out any screws (then "pop" it out if necc) and lower the light fixture itself. use a simple test light or volt meter to check for 12 volts to one of the wires when switched to the "on" position. if you have volatge replace the fixture. if not, trace the wire back to its switched source. check any wire at each end for continuity with an ohm meter. any reading besides 1.0 (open circuit - a shorted circuit would be blowing fuse repeatedly) is ok. the circuit goes downstream from battery feed at the fuse box, to relays and/or fuses, then on-off switches (including door closed switches) then the feed wire to the dome light, the fixture itself, then the bulb. wiring diagrams with color coding are almost impossible to get off the net for free. you'll need a $20+ repair manual if it goes that far. but cheer up, 90+% of the time it's the fixture. a quick and easy fix.

Oct 09, 2010 | 1990 Toyota Camry

1 Answer

How can I replace my rear tailight on my 2003 Thunderbird?


you should be able to remove the taillight lens. open your trunk,you may have to pull back the carpet covering the taillight retainer nuts.There should be 3 or 4 retainer nuts,these will either be a plastic wing nut style,or metal nut. remove all of them and gently pull on the lens,it should come out with very little resistance.the bulb fixtures will generally turn counterclockwise. replace burnt bulbs and replace the lens. hope this helps. Dale

Feb 14, 2010 | 2003 Ford Thunderbird

1 Answer

HOW DO I REPLACE CENTER BRAKE LIGHT BULB


this is not a bulb u must replace the entire LED fixture, to do this remove the inside trim at rear around rear hatch opening, then you will need to drop the headliner down to access the retainers that hold the third brake fixture in, very easy job.

Jul 09, 2009 | 1996 Ford Explorer

2 Answers

How to change a headlight bulb on a 1999 dodge avenger?


You have to open the hood and go at it from behind the bulb. look behind the light fixture set up and you will see where the light bulb goes. Simply twist off and pull out. the old light bulb will com out also.

Apr 14, 2009 | 1999 Dodge Avenger

2 Answers

Bulb burnt out on license plate


you need the remove the lighting fixture first to access the bulbs.

Mar 19, 2009 | 2002 Cadillac Deville

1 Answer

I am trying to change my brake lights in my 89 Cougar and cannot figure out exactly how. Any suggestions or sites???


Open the trunk of the vehicle, either by using the key or by turning the vehicle on and pressing the "open" button on the inside left of the glove box. Next, you will have to peel back the grey felt lining inside of the trunk, closest to the rear of the vehicle. Third you need to locate the three point, tan plastic, bulb fixtures and unscrew them. You will now see the bulb. Remove the thin metal locking device by pulling the curved end around the tan plastic fixture, then pull the bulb out. Replacement bulb is a 3157 tail light bulb. Insert the new bulb, place the 90 degree angle bent end of the thin metyal lock bac on the edge of the fixture, wrap the lock around it until it clicks in place and matches the still un-tampered opposing sides bulb and lock. Screw the fixture back in, replace the grey felt and you're done, repeat for the next side.

Jan 28, 2009 | 1989 Mercury Cougar

1 Answer

Front sidelamp new bulb holder replacement


Open hood. 
Look behind light fixture in engine side of opening. 
See little plastic doors. 
Open little doors. 
Disconnect wire to bulb. 
Unsnap the little wire snap holding bulb in place. 
Remove bulb. 
Put new bulb in. 
Plug back in wire...close little door, close hood. 
3 minutes, if that

Dec 10, 2008 | Mercedes-Benz E320 Cars & Trucks

Not finding what you are looking for?
2003 Jaguar S-Type Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...