Question about Hyundai Motor 2003 Elantra

1 Answer

Rear brake bulb replacment

I have removed the three screws and the bottom left hand corner will not budge. Is there another screw or am I supposed to do something with the drain looking plug?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,280 Answers

Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Posted on Oct 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

Tip

Brake bleeding procedure (step by step)


Required tools and supplies:

Box-end wrench suitable for your car's bleeder screws.
(An offset head design usually works best)
Extra brake fluid (about 1 pint if you are just bleeding)
(3 if you are completely replacing the fluid)
12-inch long section of clear plastic tubing (sized to fit snugly over your car's bleeder screws)
Disposable bottle for waste fluid.
Brake cleaner.
One assistant
(to pump the brake pedal).


1. Open the hood and check the level of the brake fluid reservoir.

2.Add fluid as necessary to ensure that the level is at the MAX marking of the reservoir.

3.Do not let the reservoir become empty at any time during the bleeding process.

4. Begin at the corner furthest from the driver and proceed in order toward the driver.
(Right rear, left rear, right front, left front.)

This will also allow the system to be bled in such a way as to minimize the amount of potential
cross-contamination between the new and old fluid.

5. Locate the bleeder screw at the rear of the caliper body (or drum brake wheel cylinder.) (Remove the rubber cap from the bleeder screw)
6. Place the box-end wrench over the bleeder screw. An offset wrench works best since it allows the most room for movement.
7. Place one end of the clear plastic hose over the nipple of the bleeder screw.
8. Place the other end of the hose into the disposable bottle.
9. Place the bottle for waste fluid on top of the caliper body or drum assembly.
(Hold the bottle with one hand and grasp the wrench with the other hand)

10. Instruct the assistant to "apply." The assistant should pump the brake pedal three times,
hold the pedal down firmly, and respond with "applied." Instruct the assistant not to release
the brakes until told to do so.

11. Loosen the bleeder screw with a brief ¼ turn to release fluid into the waste line.
The screw only needs to be open for one second or less. (The brake pedal will "fall" to the floor
as the bleeder screw is opened. Instruct the assistant in advance not to release the brakes
until instructed to do so.)

12. Close the bleeder screw by tightening it gently.
13. Instruct the assistant to "release" the brakes. Note: do NOT release the brake pedal while
the bleeder screw is open, as this will **** air back into the system!

14. The assistant should respond with "released."
15. Inspect the fluid within the waste line for air bubbles.
16. Continue the bleeding process until air bubbles are no longer present.
Be sure to check the brake fluid level in the reservoir after bleeding each wheel!
Add fluid as necessary to keep the level at the MAX marking. (Typically, one repeats
this process 5-10 times per wheel when doing a ‘standard' bleed.)

17. Move systematically toward the driver – right rear, left rear, right front, left front -
repeating the bleeding process at each corner. Be sure to keep a watchful eye on the brake
fluid reservior and Keep it full

18. When all four corners have been bled, spray with brake cleaner and wipe dry with a clean rag.
Try to avoid spraying the brake cleaner DIRECTLY on any parts made of rubber or plastic, as the cleaner
can make these parts brittle.

19. Test the brake pedal for a firm feel.
(Be sure to inspect the bleeder screws and other fittings for signs of leakage. Correct as necessary.)

20.Road Test.

on Aug 29, 2010 | Ford F-150 Cars & Trucks

1 Answer

How can I take off the tail light assembly to replace the bulb for the left tu


Open the trunk. In the left corner where the lamp assembly is, you should see two screw covers that cover the screws holding in the lamp assembly.

12_5_2012_6_45_21_pm.jpg

Remove these covers to find the screws, and unscrew them to pull the taillamp assembly out of the vehicle body. Disconnect the lamp wiring harness, turn the bulb socket counterclockwise to pull out the socket, revealing the light bulb. Then pull the bulb right out of the socket and replace it with a new bulb.

Replace the socket, turning it clockwise. Replace the taillight assembly. Check that the taillamp assembly tab, located at the bottom of the taillamp assembly, is aligned to the facia bracket before securing the screws.
12_5_2012_6_46_06_pm.jpg


Screw the taillamp assembly back into the vehicle body and replace the screw covers. Check to make sure the new bulb works properly.

Your owners manual specifies that the rear left turn lamp is a lamp with bulb number 3057K. You should be able to find them at any automotive store or from your dealer. Hope this helps.

Dec 05, 2012 | 2011 GMC Terrain

1 Answer

How to change the third break light bulb in a 2007 hyundai sonata ?


From 2006 to 2010, the Sonata's 3rd brake lamp requires the rear package deck be removed to access that bulb.
1. Remove the rear passenger seat bottom (remove two12mm bolts between the seat back and the seat bottom - tilt the seat back forward to locate these bolts).
a. Press the two bottom front edge tabs to release the front of the seat bottom from the floor.
b. Remove seat bottom & set aside w/two 12mm bolts
c. Tilt both seat backs downward
2. Remove the left & right hand shoulder cushions (12 mm bolt at the bottom of each cushion)
a. Remove seat belt from shoulder cushion guide at the top of the cushion
b. Lift up and forward on shoulder cushions to remove them (if equipped with side airbags, disconnect wire harness connector).
c. Set shoulder cushions aside w/two 12mm bolts
3. Using a small flathead screwdriver, pop out the 'SRS' button cover from the C pillar panels on the left & right hand side to access either the phillips head screws, 10mm bolts, or #30 Torque Screws
a. Remove screws and set aside
b. Using a standard flathead screwdriver, pop out the C pillar panels on both sides (clips hold these panels in place)
c. Set these panels aside after removal w/screws/bolts
4. Trunk Access-way panels are held in place by phillips head screws (two at the bottom (left and right hand sides) and 4 to 5 at the top .
a. Remove left and right hand panels and set aside w/screws.
5. Rear package deck held in place with two plastic clips (white, yellow or pink)
a. lie on your back inside the trunk (trunk lid open to allow for more light). Looking through access hole find 3rd brake light wire harness connector & disconnect.
b. locate package deck clips, one on the left and another on the right on the underside of the pckage deck
c. Squeeze clips to push them out - package deck will come loose
d. Remove package deck & remove 3rd brake lamp bulb socket (turn counter clockwise to remove). Replace bulb & reassemble in reverse order.

Sep 05, 2011 | Hyundai Sonata Cars & Trucks

1 Answer

Hi, i want to change the rear brake shoes on a 95 toyota granvia , is the hub nut left hand or right hand thread as it wont budge, thanx.


That nut is a locking nut and requires you to remove a locking washer from the hub itself, I use a flat head screw driver and a rubber mallet ( tapping with a medium strength) to free it up this usually needs to be replaced.

Jul 12, 2011 | Toyota Passenger Cars & Trucks

1 Answer

Replace rear brake light.


Open rear hatch. You'll see 2 black screws on the brake light assembly. Remove these 2 screws and pull the assembly out. There, you'll see wires attached to a long grey strip which holds the bulbs. There are 2 screws on each side of the top and bottom of this strip. Remove these and this plastic strip will pull straight out with the bulbs attached to it. You now have access to all 3 bulbs to replace with new ones.

Feb 04, 2011 | 2004 Chevrolet TrailBlazer

1 Answer

2002 impala brake lights/rear directional signal went


You should be able to access the bulb from the truck without removing any covers. the socket that goes into the back of the housing should twist to allow you to replace the bulb. try to twist and pull.

Jun 11, 2009 | 2005 Chevrolet Impala

1 Answer

2004 Honda Odyssey EX brake light replacement. How do you remove


open the rear hatch. Next to the brake light assembly, between it and the hatch there are two flap doors in the brake light trim. Take a small flat blade screwdriver and open these doors. The hinge side of the flap is nearest the hatch opening. When opened, the flaps will reveal two screws. Remove these. Then wrap a flat blade screwdriver with some tape (protects the paint) and put the blade at the front outside corner of the brake light assembly. Pry gently rearward and a plastic spear point clip will release. With the assembly off, you can see how to twist out the bulb sockets and replace the bulbs. to replace, put the spear point clip in first, replace the screws, and close the flaps in the trim.

May 30, 2009 | 2004 Honda Odyssey

1 Answer

How to change my rear brake light bulb


Okay you need to lift your trunk remove any carpeting remove hidden screws to undo light fixture be careful not to drop the case once case is in your hand remove the appropriate bulb that needs replacing after wards reinstall light housing/casing and screws good luck with this. Please Rate Me. And for further assistance you can always ask me.

Apr 25, 2009 | Toyota Avalon Cars & Trucks

1 Answer

Left front turn signal bulb for 2001 Pontiac Montana


There is only one screw to remove that releases the mounting tab at the upper inner corner of the assembly. That screw has a plastic wingnut molded onto it so you can turn by hand. Once that is removed, the assembly can be pulled straight forward. At the inner bottom corner, a spring clip faces straight rearward. Pull with enough force to to release the clip from its slot. Only two "Fingers" hold the rear of the assembly in the sheet metal holes.

Oct 16, 2008 | 2003 Pontiac Montana

Not finding what you are looking for?
Hyundai Motor 2003 Elantra Logo

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...