Question about 2002 Pontiac Grand Prix

1 Answer

What is the proper tourqe for the axle nut when replacing the wheel hubs on a 2002 pontiac grand prix

Posted by on

  • fschill Sep 24, 2009

    Just to double check, that is for the front wheel bearing nut right?

    thanks

  • fschill Sep 25, 2009

    thanks a lot.gonna get working now

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,011 Answers

The corrected torque for the outside axle nut is 159 ftlbs 215(N.m) This should do the trick:)

Posted on Sep 24, 2009

  • mike loshbough
    mike loshbough Sep 24, 2009

    yes that is the axle nut torque .The 3 bolts that hold the bearing hub in 45 ftlbs

  • mike loshbough
    mike loshbough Sep 24, 2009

    The axle nut is the big nut that goes over the hub

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front wheel bearing torque


Better late than never Brucy....CLICK HERE TO SEE YOUR WHEEL BEARING GUIDE. Repair Guides Front Suspension Wheel Bearings AutoZone com

Apr 02, 2014 | 2006 Pontiac Grand Prix

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

Front axle nuts size for 2003 pontiac grand prix


2002 Grand Prix front axel nut holding on hub is a 33MM or 1 5/16 deep socket

Feb 08, 2012 | 2003 Pontiac Grand Prix

2 Answers

Is the wheel bearing and hub 1 unit or can u replace just the bearing


Good Evening, these days it is a whole hub assembly and is held in by three bolts after you remove your caliper and rotor and then the nut off of the cv axle, then you can remove your hub assy bolts. One Note be sure to pay attention to the position of your ABS wire if your car has antilock brakes as to put it back in the same position. And keep safety in mind if you do it yourself.

Nov 03, 2010 | 2002 Pontiac Grand Prix

1 Answer

How do you remove a front cv axle?


remove the tire, seperate the lower ball joint from the knuckle, remove the axle nut, push the axle out of the hub, use a prybar to gently pop the axe out of the transmission (make sure you have a drain pan under the trans to catch any fluid that may come out). When reinstalling make sure you tighten the axle nut to the proper spec. This will keep your wheel bearing from going bad.

Sep 28, 2010 | 2001 Pontiac Grand Prix

1 Answer

How to replace wheel hub/ bearing assembly and do I torque the new assembly


remove brake caliper, rotor,outer tie rod.remove drive axle nut. remove 4 bearing bolts( from back)

Nov 29, 2009 | 1999 Pontiac Grand Prix

1 Answer

I am replacing the wheel bearings on my 2001 Pontiac Gran Prix. I am needing to know the torque specs for those?


ok the hub to steering knuckle bolts are 96 ft lbs,the caliper bracket to steering knuckle are 133 ft lbs,and the axle nut is 159 ft lbs,good luck

Sep 26, 2009 | 2001 Pontiac Grand Prix

1 Answer

Rotor


You do not need to pull the axle nut loose the rotor will slide off wheel hub assembly.you might need to tap it off if been on a long time.all that has to come off is the caliper

Aug 20, 2008 | 1998 Pontiac Grand Prix

1 Answer

1998 pontiac gtp ,


remove the right side wheel
seperate the ball joint
you may have to remove the stablizer bar link
remove the drive axle nut 32mm or 1 5/16
slide the front of the axle back through the hub bearing
then pop the axle out of the transmission
then install your new axle and reassemble

Jul 17, 2008 | 1999 Pontiac Grand Prix

Not finding what you are looking for?
2002 Pontiac Grand Prix Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...