Question about 1998 Jeep Grand Cherokee

1 Answer

How do I fill the coolant system. The water pump out let hose is much higher that the cap?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 62 Answers

Fill the actual radiator...Not the overflow tank. Mike. Rate 100% and respond back please.

Posted on Sep 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the thermstat at in a 1998 ford taurus?


I'm guessing you can't find it because it's in a separate housing or located under the lower battery tray in the housing (depending on model of engine). Even though this is specific for 1998; I believe it's the same for 1996-1999 Taurus's. I have access to illustrations, but only .gif and/or .bmp extensions were available which would not copy here. If you need these, I will try an extension change to .jpg. Good luck, this should be enough info. It is helpful to include the engine size in question, for future reference...

Thermostat, Water


c:\users\bob\appdata\local\temp\msohtmlclip1\01\clip_image001.gif CAUTION: Do not mix Standard (green) Coolant with Extended Life Coolant (orange). If mixing occurs, drain engine cooling system and refill with originally equipped coolant type. If this contamination occurs the service change interval on Extended Life Coolant will be reduced from 6 years/150,000 miles to 3 years/30,000 miles.
1.c:\users\bob\appdata\local\temp\msohtmlclip1\01\clip_image001.gif WARNING: NEVER REMOVE THE PRESSURE RELIEF CAP UNDER ANY CONDITIONS WHILE THE ENGINE IS OPERATING. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO THE COOLING SYSTEM OR ENGINE AND/OR PERSONAL INJURY. TO AVOID HAVING SCALDING HOT COOLANT OR STEAM BLOW OUT OF THE COOLING SYSTEM OR DEGAS BOTTLE, USE EXTREME CARE WHEN REMOVING THE PRESSURE RELIEF CAP FROM A HOT COOLING SYSTEM OR DEGAS BOTTLE. WAIT UNTIL THE ENGINE HAS COOLED, THEN WRAP A THICK CLOTH AROUND THE PRESSURE RELIEF CAP AND TURN IT SLOWLY UNTIL PRESSURE BEGINS TO RELEASE. STEP BACK WHILE THE PRESSURE IS RELEASED FROM THE COOLING SYSTEM. WHEN CERTAIN ALL PRESSURE HAS BEEN RELEASED, PRESS DOWN ON THE PRESSURE CAP (STILL WITH A CLOTH), TURN AND REMOVE PRESSURE RELIEF CAP

THE ABOVE APPLIES TO ALL MODELS

3.0L (2V) Engine

Removal

Drain the engine cooling system so that the engine coolant level is below the water thermostat (8575) as described.
2.Disconnect the upper radiator hose (8260) from the water hose connection (8592) .
3.Remove the three water inlet connection retaining bolts. Remove the water hose connection .
4.Remove the gasket and water thermostat from the water hose connection . Do not reuse gasket.
Installation
1.Install the water thermostat , gasket and water hose connection as illustrated.
2.Install and alternately tighten the retaining bolts. Tighten bolts to 10-14 Nm (89-124 lb-in).
3.Connect the upper radiator hose to the water hose connection .
4.Fill the engine cooling system with a 50/50 mixture of Premium Engine Coolant E2FZ-19549-AA (green), (in Oregon, F5FZ-19549-CC, in Canada, Motorcraft CXC-10), or Ford Extended Life Engine Coolant F6AZ-19544-AA (orange), or DEX-COOL coolant, or a coolant meeting Ford specification WSS-M97B44-D and water, as described under Cooling System, Draining, Filling and Bleeding procedure.
5.Start the engine and check all hoses and connections for leaks. Allow the engine to warm up so that the water thermostat opens.
6.Stop the engine. Top off degas bottle as required to maintain minimum cold fill level.
c:\users\bob\appdata\local\temp\msohtmlclip1\01\clip_image002.gif
3.0L (4V) Engine
Removal

Drain the engine cooling system so that the engine coolant level is below the water thermostat ; refer to Cooling System Draining, Filling and Bleeding in this section.
2.Raise vehicle on hoist.
3.Disconnect the lower radiator hose (8286) from the water inlet connection.
4.Remove the two water inlet connection retaining bolts. Remove the water inlet connection.
5.Remove the O-ring seal and water thermostat from the water thermostat housing. Inspect O-ring for damage and replace if necessary.
6.If required, remove water thermostat housing retaining bolts, water thermostat housing and O-ring from lower radiator hose tube. Inspect O-ring for damage and replace if necessary.

Installation
1.Install the water thermostat , O-ring, water thermostat housing (if removed) as shown.
2.Install and alternately tighten the retaining bolts. Tighten bolts to 8-12 Nm (71-106 lb-in).
3.Connect the lower radiator hose to the water inlet connection.
4.Lower vehicle.
5.Fill the engine cooling system with a 50/50 mixture of Premium Engine Coolant E2FZ-19549-AA (green), (in Oregon, F5FZ-19549-CC, in Canada, Motorcraft CXC-10), or Ford Extended Life Engine Coolant F6AZ-19544-AA (orange), or DEX-COOL coolant, or a coolant meeting Ford specification WSS-M97B44-D and water; refer to Cooling System, Draining, Filling and Bleeding in this section.
6.Start the engine and check all hoses and connections for leaks. Allow the engine to warm up so that the water thermostat opens.
7.Stop the engine. Top off degas bottle as required to maintain minimum cold fill level.
c:\users\bob\appdata\local\temp\msohtmlclip1\01\clip_image003.gif
3.4L SHO
Removal
Drain the engine cooling system so that the engine coolant level is below the water thermostat ; refer to Cooling System, Draining, Filling and Bleeding in this section.
2.Remove battery.
3.Remove power distribution box.
4.Remove battery tray.
5.Disconnect upper radiator hose and position out of the way.
6.Disconnect the lower radiator hose from the water inlet connection (8K528) .
7.Remove the two retaining bolts. Remove the water inlet connection .
8.Remove the O-ring seal and water thermostat from the water pump (8501) . Inspect O-ring for damage and replace if necessary.

Thermostat

Installation
1.Install the water thermostat , O-rings and water inlet connection as illustrated.
2.Install and alternately tighten the retaining bolts. Tighten bolts to 8-12 Nm (71-106 lb-in).
3.Connect the lower radiator hose to the water inlet connection .
4.Install upper radiator hose . Position spring clamp securely.
5.Install battery tray.
6.Install power distribution box.
7.Install battery.
8.Fill the engine cooling system with a 50/50 mixture of Premium Engine Coolant E2FZ-19549-AA (green), (in Oregon, F5FZ-19549-CC, in Canada, Motorcraft CXC-10), or Ford Extended Life Engine Coolant F6AZ-19544-AA (orange), or DEX-COOL coolant, or a coolant meeting Ford specification WSS-M97B44-D and water; refer to Cooling System, Draining, Filling and Bleeding in this section.
9.Start the engine and check all hoses and connections for leaks. Allow the engine to warm up so that the water thermostat opens.
10.Stop the engine. Top off degas bottle as required to maintain minimum cold fill level.


ad52e081-499a-4e51-a3ef-9bc69a1f9941.gif


5a54c428-0afd-4a37-96ed-ce2033822e88.gif


3f8c57db-bea6-4205-94d5-9a1eb24706fa.gif

Sep 01, 2014 | 1998 Ford Taurus

1 Answer

Water flowing out of radiator when idling 93 nissan terrano v6 petrol auto trans


If the coolant was hot when you noticed water coming out the radiator, that is normal from the heat expansion of the coolant. That is why there are coolant overflow tanks-also called coolant expansion tanks.
When refilling coolant, always top up the radiator, and fill the overflow tank to at least the cold mark level (about half-way up on the tank). With cap off, run engine till the thermostat opens- upper radiator hose will become hot-then shut off engine, add coolant to radiator as needed, replace cap. This method of filling will help to expel any trapped air in the system. Oh, and remember to set your heater controls on high when filling coolant, so the heater core and lines also circulate and expel air.
Check the seal on the radiator cap that it is still good. The cap seal is important to seal the coolant system, as it is a closed system under about 15 psi of pressure. The reason to pressurize the system is that the pressure will raise the boiling point of the coolant by about 10 degrees- important when you consider how hot the coolant has to be when running. OK, enough tutorial-I don't think you have a problem with the water pump! G'd luck, reeve.

Nov 22, 2012 | 1993 Nissan Pathfinder

3 Answers

Engine overheating i have replaced the radiator has plenty of water


replace thermostat.then bleed coolant system, this is how you do it.fill the cooling coolant system with 50 / 50 dexcool and water to raise boiling point,straight water will evaporate boil away cause engine to overheat catch fire thats why you need 50 / 50 mixture antifreeze and water.to bleed coolant system first fill coolant system until coolant stay at the full cold mark on the the coolant overflow jug,then you start engine allow it to idle,place the heater and ac control in any ac setting except max and the temperature control to the highest setting,run engine until lower hose to water pump is hot. with the engine hot run the engine speed up to 3000 rpm and allow it return to idle, repeat this 5 times. slowly open the bleed valve on the thermostat housing or look for bleed valve at the water pump heater hose.open bleed valve for 15 seconds to expel any trapped air.then top off the coolant as necessary,and when top radiator hose hot thermostat open up.keep adding cooling to overflow until coolant level stop at full cold mark dont over fill coolant.if engine seem like overheating while looking at cooling gauge turn off engine wait a while until cool off add more coolant until coolant level stay stable and dont drop any.when open radiator overflow cap use large rag over the radiator cap to keep from getting scald open radiator cap a little at a time but dont open radiator cap until engine cool down first.replace the radiator overflow cap, thermostat,and engine coolant temperature sensor and check the cooling fans fuses and relays see what happens.

Aug 18, 2012 | 1998 Oldsmobile Intrigue

2 Answers

Have changed the water pump, thermostat, radiator, radiator cap, all hoses. 2001 chevy venture, still running hot? How long does it take to bleed the cooling system?


If the system fills via an expansion tank, I would recommend removing the top hose from the radiator and filling the system by pouring the coolant in through the hose until it begins to flow out of the upper radiator port. Reconnect the hose and then fill the expansion tank. That should take care of it.

Jun 26, 2011 | 2001 Chevrolet Venture

1 Answer

Have to replace water pump on 98 Ford Taurus. Any hints or suggestions would be appreciated before I get out in the snow and cold to fix this.


You can change the water pump by doing these steps:

  • With the engine off and cold, o pen the hood and locate the vehicle’s radiator and water pump.
  • Remove the radiator cap.
  • Install a pressure tester on the radiator. Apply the pressure indicated on the radiator cap or in the owner’s manual.
  • Inspect the water pump for leaks. Remove the pressure tester.
  • Place a drain pan under the radiator. Open the drain valve or remove the lower radiator hose to drain the cooling system.
  • Remove the drive belts or serpentine belt.
  • Remove any hoses connected to the water pump.
  • Unbolt the water pump from the engine. Remove the water pump.
  • Using a gasket scraper, clean the mounting surface on the engine block.
  • Install a new gasket and attach the new water pump to the engine with the original mounting bolts. Tighten the bolts to the manufacturer’s specifications.
  • Re-install any hoses and belts that were removed.
  • Re-install the drain plug or lower radiator hose.
  • Refill the radiator with a 50/50 mix of coolant and distilled water. Pressure test the cooling system and check for leaks.
  • Check and fill the overflow reservoir with coolant.
  • Leave the radiator cap off and start the engine. Idle the engine to remove trapped air from the cooling system. Add coolant if necessary.
  • Install the radiator cap.
  • Road test the vehicle and monitor the temperature gauge. If the vehicle runs hot, there may be an air pocket in the cooling system. Allow the engine to cool off and add the necessary coolant.

Feb 12, 2010 | 1998 Ford Taurus

3 Answers

I FILLED THE COOLANT SYSTEM AND BECAUSE THE WATER PUMP OUT LET SITS HIGHER THAN THE RADIATOR I HAVE A ARI LOCK. HOW CAN I VENT THIS ARI OFF?


Hello ,this is what i do for this vehicle .First take off one of the heater hoses going to the top of the water pump.Next make sure the radiator cap is ON .Then take a funnel ,stick it in the waterpump tube .Then poor the antifreeze in slowly until antifreeze comes out of the hose that was taken off .this will put antifreeze into the engine and radiator.:)

Sep 24, 2009 | 1998 Jeep Grand Cherokee

5 Answers

Help with cooling system!!


Need to know engine size. Normally filling the cooling system requires a cold engine and slowly adding coolant untill full. Run engine till warm and recheck coolant level when engine cools. Add coolant if needed and rewarm. Recheck level . On some engines this may require this operation a few times

Jun 11, 2009 | 1997 Chevrolet Monte Carlo

1 Answer

1999 Mercedes e-320 water pump


Good morning;
does this critter have a radiator fill w/cap? I've run accross som large Sotrd trucks that don't.
Well, anyway, it soesn't make sense you would need to fill the radiator via the resenoir. That is only good for short pressure relief and cook down vacuum recovery of coolant. 60/40 is the mix ratio. If it hs a resevoir it should have a radiator cap.The air in system will purge itself as it starts to circulatte cioolant. turn heater off till your system is full, then on when engine reaches operating temp. then if needed top iff coolant. Leave radiator cap off while waiting for coolant to start circulating. When thermostat opens out comes the air. Then put coolant mix in reservoir to fill line. check for leaks and all hose clamps are tight and you should be set, Good luck - Ned

Apr 13, 2009 | 1994 Mercedes-Benz E-Class

1 Answer

Coolant filling up overflow bottle and not returning Started intermittently No coolant leaks Changed Hoses Cap Thermostat Cooling system has always had good quality coolant and is clean inside...


You may need to ask AAA to put a radiator pressure tester on the resevoir bottle and pump it up to operating pressure(Pressure cap rating) and see if it over pressurises while it is running at operating temp,rev engine up and down and watch what the testers pressure readings do,it should move up and down in sync with the water pump.If the pressure keeps building i would have to believe that combustion chamber gases are over pressurising your cooling system.Also test the pressure cap is functioning within factory specs.

Oct 30, 2008 | Mitsubishi Passenger Cars & Trucks

Not finding what you are looking for?
1998 Jeep Grand Cherokee Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...