Question about 1966 Ford Mustang

Open Question

HOW TO REPLACE THE ANTENNA ON A 66 MUSTANG? - 1966 Ford Mustang

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would cause the the instrument pannel voltage regulator to fail on a 66 mustang? The gauges do not work mow.


It's called a CVR, constant voltage regulator, to keep all gauges with same voltage all the time, regardless of spikes. They seldom fail. I did not think we used one back in 66, but I did not start working for Ford until 1975. I would replace it and seee what happens. Let me know.

Jan 20, 2011 | 1966 Ford Mustang

2 Answers

66 mustang help


Remove the steering wheel and replace the directional switch

May 31, 2010 | 1966 Ford Mustang

1 Answer

My 66 mustang pops when I turn it right. I think


ball joints are your problem, but also have your tie rods checked. if you can move your tie rods with your hand they need to be replaced. check your balljoints by lifting your car and grabbing a front wheel and moving it up and down if you feel slack, replace balljoints as soon as possible, as it is dangerous to drive in that condition.

May 12, 2010 | 1966 Ford Mustang

1 Answer

My 66 mustang pops when I turn it right. I think


The first suggestion is to replace the tie rods. In most cases where there is alot of play and a popping sound when the wheel is turned is because the inner parts of the tie rods are worn through and should be replaced as soon as possible. You could lose control easily if the tie rod pops out completely.
There are inner and outer tie rod ends which keep the wheel in a straight line while attached to the axle. Tie rod ends can be found on the inside of the wheel and are attatched to a longer metal bar which allows tight steering by controling the path of the wheels. The tie rod ends themselves look of a ratchet, with the handle end being threaded.

Mar 20, 2010 | 1966 Ford Mustang

1 Answer

How do you replace an antenae on a 1965 mustang.


Disconnect the cable at the radio. Then unscrew the hardware holding the antenna to the fender. Then pull the antenna base out of the fender, disconnect the cable from the antenna base turning it back and forth with pliers or you can cut it. Do not let the cable fall back into the fender. Now take the cable from the new antenna and duct tape it to new antenna cable. Now inside the car pull on the old cable until the new cable reaches the radio. Plug cable into radio then hook up the hardware on the fender for the new antenna and you're done. Good luck.

Feb 27, 2010 | 1965 Ford Mustang

3 Answers

How to install accelerator pedal spring in 1966 mustang.. how does the spring install


i have a 66 mustang. thespring attaches to the throttle body and not sure from there

Nov 06, 2009 | 1966 Ford Mustang

1 Answer

66 mustang straight six engine won't crank over


Check the Battery and Connections. Not a lot of Guess work on the Old Mustangs. You may need to Clean the Cables to the Battery, Could be a Little Corroded. Please rate my Response, I need all the Help that I can get! Thanks!

Jan 26, 2009 | 2000 Nissan Maxima

1 Answer

LOCATION OF SAFTEY NEUTRAL SWITCH ON 66 MUSTANG


if it is a manual trans it is in the clutch arm under the dash and if automatic it is at the base of the steering column

Nov 28, 2008 | 1966 Ford Mustang

2 Answers

Need diagram


Hi pgarrity,hope this helps my friend good luck,this is simplified :)38282e1.jpg

Nov 10, 2008 | 1965 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

484 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...