Question about 2006 Chrysler PT Cruiser

1 Answer

I need to replace my starter what tools do i need ?and what is the easiest way to remove it?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 92 Answers

Disconnect negative battery terminal. Remove air cleaner assembly and battery. Then you can remove the 15mm bolt holding the upper part of the starter to the bell housing. Next raise the vehicle by jack on jack stands or suitable support. Remove lower bolt from starter and then you will be able to lower it enough to access the wiring to the starter. Be sure to retain the shim that goes between starter and housing. Install is reverse of removal.

Posted on Sep 24, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 104 Answers

SOURCE: need to replace starter

should be 2 bolts 15mm and then 2 nuts on the starter 13mm and 8mm. this is a very easy starter to do. make sure you remover ground battery cable before doing this starter.
good luck,
michael

Posted on Apr 29, 2009

d_hubbs
  • 270 Answers

SOURCE: how to remove a starter from a 1999 chevy silverado 4x4 pickup

1) Disconnect Negative Cable on Battery
2) Starters on right-side Close to Trans. Bell Housing
3) Remove the 2-Starter Bolts and Shim if it's
if it has shims.
4) Remove the wires off Solenoid: Mark Them:
5) Remove the Heat Gaurd Over top of Starter:
6) Take Starter on Out.

To Re-Install Reverse the Procedure that you Removed the Starter. NOTE: the Shims if there was any are only nessary if the Casting of the Starter is not Exactly or Close to The Original.

Be sure that All the Wires you Took off the Starter Solenoid are put Back on the Exact Same Terminal. And Snug them up .Be careful not to Over Tighten,:
Specs on Bolts Are :
Torque Starter Battery Cable Nut to 90 inch lbs
Torque Smaller ingnition wier nuts to 18 Inch Lbs
Torque the 2- Starter Mounting Bolts to 35 FOOT lbs.
Remember if your Old Starter Had Shims the New one MIGHT need Shims.All Starters Casting are just a Little Different. like by thousands of an inch. So if you have problems you might have to remove or add shims,they come in different sizes. Hope this has helped you,Please let me know how this solution Helped. Thank You: From d_hubbs

Posted on Jun 08, 2010

daves944
  • 1050 Answers

SOURCE: need to replace starter

I'm pretty sure the last time I did this, I went through the right front wheel well after removing the tire. You may have to remove a clamp or two that hold some some steel hydraulic lines, just bend them a little out of the way and you will have access.

Posted on Mar 14, 2009

  • 1 Answer

SOURCE: Where is the starter located and what tool are required to remove

you have to look with a flash light depending on the vehicle, go under the vehicle and look left to the right of the bottom of the engine and you should see a elongated part no bigger than 12 inches(smaller) and it will have no more than three wires with a smaller cylinder attacked to it. most of the time there will be 3 bolts or nuts holding it on. tools= socket set; standard for domestic vehicles and metric for import vehicles, open end wrenches and wire cutters(just in case). most of the time on domestic cars you will use a size of 1/2 to 9/16 for you tools. start with disconnecting the battery then remove the starter. when putting the new one on just turn the teeth on the starter to line up with the wheel in the engine, you will see that when you remove the old starter. splice the new power wire if needed for the power, a new wire should come with the new starter if it is needed. hook the battery back up and enjoy!

Posted on Jan 12, 2009

burdfrenzy
  • 348 Answers

SOURCE: 1987 toyota camry starter removal diagram

Hi there, Best thing to do is buy a Haynes or Clinton's repair shop manual at your local AP store for your particular vehicle. Then read up on it in the trouble shooting section or the step by step RR section. You can purchase these at your local Auto Parts store or buy them on line at ebay burdfrenzy

Posted on Oct 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u change a starter on a 99 grand am with a 2.4


Remove battery wires from battery by loosening the termanals and set them off to the side. Remove wires from the starter making sure to remember where they go. Remove the bolts holding the starter in place. Lower starter down and out, or maybe even up through the top, which ever way you think is the easiest. you may need to manipulate it, turning it around so that it will come out. Replace the new one the same way you took that one out.

Dec 05, 2013 | 1999 Pontiac Grand Am GT

2 Answers

How do i replace my own starter on my 1987 licoln town car?


1. Raise the car and support it.
2. Disconnect the negative battery cable.
3. Crawl under the car and locate the starter. It is easiest to do this by following the positive power cable from the battery down to the starter.
4. Remove positive cable from starter.
5. Remove wires from solenoid.
6. Remove bolts holding starter to the transmission bell housing.
7. Remove the starter.

Installation is the reverse of removal.

Oct 26, 2010 | 1987 Lincoln Town Car

1 Answer

What tools are needed to replace starter on '93 cutlass supreme


a good socket set to remove the starter retaining bolts, usually a 10mm or 12 mm ring spanner to remove the power connections. a car jack and axle stands

Mar 24, 2010 | 1993 Oldsmobile Cutlass Supreme

1 Answer

Hi my name is Ronnie i have a 93 mazda mx3 and having a lot of grinding ithought it was my starter but i removed and found teeth missing off the flywheel need to know the easy way to remove trany if any...


The easiest way is to get the car up high enough to remove it from the bottom. If you are mechanically inclined, the rest is just nuts and bolts. You will need a pickle fork tool though. Also i you remove the clutch and don't plan on replacing it (not advised) you will need an alignment tool.

Jan 12, 2010 | 1992 Mazda MX-3

1 Answer

Replacing a starter in a PT. Cruiser 2001


Remove battery and battery support you'll be able to undo starter bolt's trough there and slip starter out.

Dec 08, 2009 | 2001 Chrysler PT Cruiser

2 Answers

What is the easiest way to change the starter on 91 olds ciera 3.3 with Ac.


Hello. Here are the steps. Disconnect the - battery cable
Raise and support vehicle
Disconnect wiring at top of starter
Remove starter mounting bolts
Remove starter.

You can go to many auto parts stores these days and borrow the tools you need. good luck.

Nov 20, 2009 | 1991 Oldsmobile Cutlass Ciera

1 Answer

Need to replace starter


should be 2 bolts 15mm and then 2 nuts on the starter 13mm and 8mm. this is a very easy starter to do. make sure you remover ground battery cable before doing this starter.
good luck,
michael

Apr 29, 2009 | Pontiac Montana Cars & Trucks

1 Answer

Where is the starter located on a 2000 Cabrio?


disconnect ground cable make sure the radio is turn off so you wont lose code.raise support front of car.you need a floor jack.for A3 engine.place a piece of wood on floor jack saddle .place floor jack under the engine oil pan.slightly raise engine just a little bit to take load off engine mount.the starter and engine uses same bolts removes bolts .remove starter label wires remove postive battery cable.from starter .the 010 transaxle engines remove bracket that support starter to engine remove starter bolts support starter then remove it.on vechicle with manual transmission the bushing where starter fits into bell housing should be replaced besure to get a bushing removing tool.

Mar 22, 2009 | 2000 Volkswagen Cabrio

1 Answer

Need to replace starter


I'm pretty sure the last time I did this, I went through the right front wheel well after removing the tire. You may have to remove a clamp or two that hold some some steel hydraulic lines, just bend them a little out of the way and you will have access.

Mar 14, 2009 | 1995 Nissan Pathfinder

1 Answer

94 toyota carolla starter clicks eventualy starts


You have two options: replace the starter (easiest, but most expensive), or replace the contacts (cheaper, but more work involved).
In any case, you have to remove the starter. Disconnect the battery BEFORE you start. Locate the starter and remove the wires going to it. The starter is held onto the transmission with 2 large bolts. Remove both, and slide the starter out.

If you want to change the contacts, observe the starter, locate a metal plate held on with 3 bolts. Remove the bolts and the plate. You will now see a plunger, and 2 copper colored contacts. Those are what needs to be replaced. Changing the contacts is easy, just do one at a time, and ensure that all insulators are installed properly on reassembly.

Jan 13, 2009 | 1994 Toyota Corolla

Not finding what you are looking for?
2006 Chrysler PT Cruiser Logo

1,903 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...