Question about Chevrolet Blazer

1 Answer

Ignition lock cylinder removal for a 1975 blazer. this does not have the screw to remove the cylinder lock like on a 1976 blazer.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 3,433 Answers

Turn to accessory and use straight paper clip yo pud pi inside the hole in front of the key while turning key to on and pulling out using key for a handle.

Posted on Sep 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

In my son's 1975 Chevy truck, the ignition switch


Hi Willy, It may be a problem of a worn key, but on that age of vehicle it's more likely to be a worn ignition barrel. Try and have the key replaced first and it that fails, be ready to replace the barrel and key. Happy new year and Regards John

Jan 06, 2013 | Cars & Trucks

1 Answer

How do i tear apart my steering column in my 84 dodge pickup so i can change my ignition switch?


  1. NON TILT WHEEL
  2. Remove the steering wheel.
  3. Remove the turn signal switch.
  4. Unfasten the two screws that release the buzzer switch (if equipped), then remove the switch.



0900c15280052e49.jpg

Fig. Fig. 2: Removing the ignition buzzer

  1. Remove the retaining screw and lift the ignition lock cylinder lamp out of the way.



0900c15280052e4a.jpg

Fig. Fig. 3: Ignition key lamp

  1. Remove the bearing housing.
  2. Detach the coil spring.
  3. Remove the lock plate from the shaft.



0900c15280052e4b.jpg

Fig. Fig. 4: Lock lever plate removal

  1. Unfasten the 2 retaining screws and lift the lock lever guide plate to expose the lock cylinder release hole.
  2. Insert the key and place the lock cylinder in the LOCK position. Remove the key.
  3. Insert a thin punch into the lock cylinder release hole and push inward to release the spring-loaded lock retainer. At the same time, pull the lock cylinder out of the column.



0900c15280052e4c.jpg

Fig. Fig. 5: Depress the lock plate which will expose the lock cylinder release hole

  1. Remove the 3 retaining screws and lift out the ignition switch.

To install:
  1. Position the ignition switch in the center detent position (OFF).
  2. Place the shift lever in PARK.
  3. Feed the wires down through the space between the housing and jacket. Position the switch in the housing and install the 3 retaining screws.



0900c15280052e4d.jpg

Fig. Fig. 6: Lock levers and spring assembly installed

  1. Place the lock cylinder in the LOCK position, and press it into place in the column. It will snap into position.
  2. The remainder of assembly is the reverse of disassembly.

Aug 14, 2011 | 1984 Dodge Pickup 4WD

1 Answer

Need to replace ignition cylinder. no keys


This is not an easy repair due to anit theft requirements. need to chisel off bolts.

Section 11-04: Steering Column 1997 Probe Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000
Ignition Switch Lock Cylinder Removal
  1. Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the four lower steering column shroud screws.


    j5021c.gif

  1. Separate the upper and lower steering column shrouds.
  1. Remove the ignition switch lock cylinder illumination miniature bulb from the lower steering column shroud.
  1. Remove the upper and lower steering column shrouds.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal and installation procedure.
  1. If equipped, remove the ignition/shifter interlock cable screw.
  1. Disconnect the ignition/shifter interlock cable (3F719) from ignition switch lock cylinder (11582).
  1. Use a chisel to remove the two ignition switch lock cylinder bolts.
  1. Remove the ignition switch lock cylinder from the steering column.
  1. Disconnect the ignition key reminder switch electrical connector.
  1. If necessary, remove the ignition key reminder switch.


    j5028b.gif

Installation
NOTE: Use new ignition switch lock cylinder bolts. Tighten the bolts until the bolt heads break off. Check for proper ignition switch (11572) operation.

To install, reverse the removal procedure.

Mar 25, 2011 | 1997 Ford Probe

1 Answer

Trying remove the ignition in toyota avalon 2000


TO REMOVE THE IGNITION SWITCH FIRST TURN OFF RADIO.AND DISABLE AIRBAGS BY DISCONNECTING NEGATIVE BATTERY CABLE WAITING 20 MINUTES UNTIL AIRBAGS DISCHARGE.TO REMOVE IGNITION SWITCH PLACE THE IGNITION KEY IN THE ACC POSITION. REMOVE THE STEERING WHEEL AND REMOVE THE STEERING COLUMN COVERS.DISCONNECT THE IGNTION SWITCH ELECTRICAL CONNECTORS.REMOVE THE SWITCH RETAINING SCREWS THEN PULL THE SWITCH FROM THE LOCK CYLINDER HOUSING.IF YOU TRYING TO REMOVE THE LOCK CYLINDER WITH LOCK CYLINDER IN ACC POSITION. USE A SMALL SCREW DRIVER OR PUNCH. DEPRESS THE LOCK CYLINDER RETAINING PIN THEN REMOVE LOCK CYLINDER. TO INSTALL NEW LOCK CYLINDER. DEPRESS THE RETAINING PIN AND GUIDE THE LOCK CYLINDER INTO THE HOUSING UNTIL THE RETAINING PIN EXTENDS ITSELF BACK INTO THE LOCATING HOLE IN THE HOUSING.

Mar 01, 2011 | 2000 Toyota Avalon

1 Answer

How to remove my key lock 2000dodge caravan


Ignition Lock Cylinder - Removal & Installation CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the air bag or SIR wiring. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
  1. Disconnect and isolate the negative battery cable from the battery.
  2. In order to disarm the air bag system, allow the SIR system capacitor to discharge for at least 2 minutes, before performing any removal procedures.
  3. Remove the screws that secure the parking brake release handle to the instrument panel.
  4. Remove the screws that secure the bottom of the lower steering column cover to the instrument panel.
  5. Disengage the retaining clip that holds the right side of the lower steering column cover to the instrument panel.
  6. Remove the lower steering column cover from the vehicle.
  7. Remove the mounting screws that hold the upper and lower steering column shrouds and remove the lower steering column shroud.
  8. Install the ignition key and turn the key cylinder to the RUN position. This is important because it will not only aid in removal of the ignition lock, but will also place the socket (in the lock cylinder housing) in proper alignment for the installation of the replacement ignition lock.
  9. Press in the lock cylinder retaining tab and remove the key cylinder (ignition lock).

    4045958.jpg
    Fig. Depress the retaining tab to remove the key cylinder
To install:
  1. Install the ignition key into the replacement ignition lock key cylinder. Turn the key to the RUN position. Depress the ignition lock key cylinder retaining tab.
  2. Align the shaft at the end of the ignition lock cylinder with the socket in the end of the ignition lock cylinder housing.
  3. Align the ignition lock cylinder with the grooves in the lock cylinder housing. Push the ignition lock cylinder into the housing until the retaining tab sticks through the opening in the lock cylinder housing.
  4. Turn the ignition key to the OFF position and remove the key.
  5. Install the lower steering column shroud and install the mounting screws.
  6. Place the lower steering column cover into correct position on the lower instrument panel and engage the clip that secures the right side of the cover to the instrument panel.
  7. Install the lower steering column mounting screws.
  8. Install the mounting screws that hold the parking brake release handle to the instrument panel.
  9. Reconnect the negative battery cable.

Hope helps (remember rated and comment this).

Aug 11, 2010 | 2000 Dodge Caravan

1 Answer

Replacing ignition lock cylinder


its not a screw. it is a slot towards the end of the switch. use a small flat screw driver and push in the spring loaded keeper, Steering wheel and blinker assemble have to be dissasembeled

Jul 28, 2010 | 1978 Chevrolet Caprice

2 Answers

My ignition is locked and will not turn. i am trying to replace the ignition but am having trouble figuring out how to remove it. do u have to take the steering wheel off and if so wont that mess up the...


You have to remove the steering wheel with a puller,and the lock plate ,with a lock plate remover tool,and the cancel for the turn signals,and then the turn signal switch,then you remove a screw on the right side about 2 o clock position,and the lock and key will slide out.

Jul 12, 2010 | 1997 Chevrolet Blazer

1 Answer

How to remove and replace the ignition switch cylinder in a 1976 chevy cheyenne 1/2 ton pickup?


Remove the horn button, nut the pull the wheel off with a puller.Remove the lock plate retaining spring using a Lock plate press. Remove the directional switch screws (3).. Lift that switch out of the way to remove the ignition lock screww
Pull out ign Lock Cylinder

Reverse this procedure to install

Jun 02, 2010 | 1977 Chevrolet Silverado 2500

1 Answer

Removal of 1976 chevy truck ignition switch


need a special tool to remove the locking plate behind steering wheel then pull turn signal switch back a little then remove screw that keeps lock cylinder in place

Oct 22, 2009 | Chevrolet C3500 Cars & Trucks

1 Answer

How do I remove the ignition lock cylinder from the steering column on a 1978 Jeep CJ7. I already have the steering column disassembled.


here are the instruction the first set are the instruction on how to remove the turn signal switch as you will need them to remove the ignition

Removal & Installataion of turn signal switch
  1. Disconnect the negative battery cable.
  2. Remove the steering wheel.
  3. Loosen the anti-theft cover retaining screws on 1976 models and lift the cover from the steering column. It is not necessary to completely remove these screws.
  4. Depress the lockplate and pry the round wire snapring from the steering shaft groove. A lockplate compressor tool is available for compressing the lockplate.
  5. Remove the lockplate, directional signal canceling cam, upper bearing preload spring, and thrust washer from the steering shaft.
  6. Move the directional signal actuating lever to the right turn position and remove the lever.
  7. Depress the hazard warning light switch and remove the button by turning it counterclockwise.
  8. Remove the directional signal wiring harness connector block from its mounting bracket on the right side of the lower column.
  9. On vehicles equipped with an automatic transmission, use a stiff wire, such as a paper clip, to depress the lock tab which retains the shift quadrant light wire in the connector block.
  10. Remove the directional signal switch retaining screws and pull the switch and wiring harness from the steering column.
  11. Guide the wiring harness of the new switch into position and carefully align the switch assembly. make sure that the actuating lever pivot is correctly aligned and seated in the upper housing pivot boss prior to installing the retaining screws.
  12. Install the directional signal lever and actuate the directional signal switch to assure correct operation.
  13. Place the thrust washer, spring, and directional signal canceling cam on the upper end of the steering shaft.
  14. Align the lockplate splines with the steering shaft splines and place the lockplate in position with the directional signal canceling cam shaft protruding through the dogleg opening in the lockplate.
  15. Install the snapring.
  16. Install the anti-theft cover.
  17. Install the steering wheel and connect the negative battery cable.
  18. Check the operation of the turn signal switch.

Removal & Installation of ignition lock switch
  1. Disconnect the battery ground cable.
  2. Remove the turn signal switch as described earlier in this section. You don't have to remove the switch completely, just set it aside.
  3. Insert the key. Position the key as follows.
    • 1976-83: With manual transmission, put it in the ON position; with automatic, put it in OFF/LOCK.
    • 1984-86: Two detent positions, clockwise, beyond OFF/LOCK.
  1. Working through the slot next to the turn signal switch mounting boss, use a thin screwdriver to release the lock cylinder.
  2. To install, insert the key in the new lock cylinder. Hold the sleeve and turn the key clockwise until it stops. Align the cylinder retaining tab with the housing slot and insert the cylinder. Push the cylinder in, rotate to engage, then push in until the retaining tab engages the housing groove.
  3. Complete the procedure in the reverse of removal.

Aug 20, 2009 | Jeep CJ7 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...