Question about 1996 Dodge Grand Caravan

1 Answer

I just replaced a front and back brakeline on my 1996 chevy suburban and realized my bleeder screws are frozen, is there another way i can bleed my brakes?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 881 Answers

Yes there is another way to do it but go slow and do it wright
Bleed by using the screw nut on the pipes you just fitted by.
Pump pedal 3times fast and hold down get someone to clamp all 2 hoses (1F/1brake pipe over rear axle) with small G clamps and then undo pipe nut on the one without clamp when pedal on floor lock up and do again ,when done 2 times put clamp from other side to the 1 you just done and do the same again to that side, when Front done take clamp from rear pipe and put on front and to the same bleeding to the rear BUT
pump up 3 times and open both nuts togeather and tighten both togeather and do the rear 4 times not 2, ANDTop up M/Cylinder every time , you might find jacking up rear of car is a lot better to remove air

Posted on Sep 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My bleeding screw for the front brakes are both broke Wat should I do I have drums in the back on a 03 Malibu how can I bleed them


You use the bleeder on the rear drums to bleed those lines but you cannot do it to front brakes until you replace the bleeders up there.

Jun 15, 2017 | Cars & Trucks

1 Answer

How do I bleed the brakes on a 1996 suburban?


if you are alone, you can fill master, open bleeders and wait until fluid appears at the bleeders. Close them, verify fluid, pump the pedal, repeat gravity procedure until no air bubbles are present

Sep 29, 2014 | 1996 Chevrolet Suburban

2 Answers

Replaced brakelines know pedal goes to floor


You either have a leak in the the system or your master cylinder is bad and allowing the pedal to push through the cylinder without bulding pressure. Check all the wheels for signs of a leak, if none and the brake fluid resivoir is full then the master cylinder on the back of the firewall is bad. These can be rebuilt very cheaply and you can do this yourself with parts from the parts store.

Apr 08, 2011 | 1998 Pontiac Sunfire

1 Answer

1996 VW Golft GTI vr6 We've replaced the master cylinder and slave cylinder due to the clutch pedal not holding preasure. We then replaced the bearings on the rear rotors. We bled the clutch, and...


When you opened the bleeder screws to the rear brakes, did you completely remove the screws ? Might also want to perform a complete visual inspection of the brake lines from the rear to the front and master cylinder.
How are you performing the bleeding process ?

Jun 19, 2017 | 1996 Volkswagen GTI

1 Answer

How to bleed brakes on a 1992 Chevy Caprice. Specifically the rear drums


start from the fartherest place from brake master cylinder, that will be the rear passenger side wheel. it takes two people to bleed brakes. you will find the bleeder valve screws at the top of inside of the rear drums on both rear wheels, have someone pump the brakes up, will take at least 4 pumps of brake pedal, at 4th pump keep pressure on pedal while you break loose the bleeder valve on the rear wheel, fluid will come out and brake pedal will go down to floor, keep pressure on brake pedal until you've tightened the bleeder screw back [note] you'll only have to back the bleeder valve out about a half turn until you see the fluid come out. after you've done the rear brakes add brake fluid to the master cylinder as it will be low. then go to the front passeger side and you will find the bleeder screw on the brake caliper. repeat the same proceedure as back. remember that pressure on the pedal is a must until you've tightened those bleeder valve screws back or else it will **** air into the brake system. suggest that you bleed all 4 wheels not just the back. after you've bled the front make sure you add more brake fluid back to the master cylinder, it will be low again. hope this helps and thank you for choosing fixya.com

Nov 21, 2010 | 1992 Chevrolet Caprice

1 Answer

I have a 1997 chevy cavalier. I replaced wheel cylinders, brake lines, front calibers master cylinder and booster. When I bleed the brakes I only get brake fluid from the front bleeder on the ABS system. I...


sometimes if you leave the bleeder screw open it will gravity bleed the cylinder.Make sure master cyl is full and do one wheel at a time.I have seen this work, I have done it.

Nov 16, 2010 | 1997 Chevrolet Cavalier

1 Answer

How to bleed antilock brakes on 1994 Chevy Suburban?


One man suction bleeder from the calipers with top off the reservoir and keep it full when you **** fluid out the caliper.

Apr 29, 2010 | 1994 Chevrolet Suburban

4 Answers

How do i bleed the brake system


First, before you do the bleeding, did you "open" any of the lines? Was there a caliper replaced?

If no line was opened, you do not need to bleed the brakes.

If so, please let me know and I will post the bleed procedures for you.

Why are you thinking about bleeding the brakes? Spongy brake pedal?

Oct 08, 2009 | 1995 Chrysler Town & Country

2 Answers

Broke a brakeline on my 1996 taurus how do i fix or cap it so i can use the car 4 wheel disc sys


It has to be replaced. If its front new break hose that runs from hard line to caliper. If rear from caliper to block on rear axel. If main line from front of car at perporationing valve back to block on rear axel.

Apr 13, 2009 | 1996 Ford Taurus

Not finding what you are looking for?
1996 Dodge Grand Caravan Logo

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...