Question about 2004 Ford Focus

Open Question

Steps in removing ignition switch on 2004 ford focus

Need instructions

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 713 Answers

SOURCE: How to replace high/low beam switch on 2004 Ford Focus LX?

Should be fairly easy. Make sure to disconnect the positive battery cable. Remove the cover from around the column behind the steering wheel. Should take a star driver to remove the screws holding the cover together. Once the screws are removed pop the cover apart and you will see the multifunction switch on the column, should have two to three screws holding it to the column remove the screws and it should come out pretty easy replace with new one and put back together.

Posted on Oct 02, 2009

Testimonial: "Thank you so much!"

  • 84 Answers

SOURCE: I need to replace a '95 Ford Bronco ignition

This one is pretty easy. just unscrew the philips screws under the key area I think there are 3 or mebe 4. then remove the plastic cover. insert your existing key, turn the key 1 click and press the release button on the bottom then pull the key, the entire lock will come out, insert the new one and put it all back together.

Posted on Feb 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Factory mode


Disabling Transport Mode

1.Place the ignition OFF.

2.Verify the battery is fully charged.

3.Place the ignition ON.

4.NOTE: Steps 4 and 5 must be carried out within 10 seconds.

Press and release the brake pedal 5 times.

5.Press and release the hazard switch 4 times (on, off, on, off).

I'd turn off the vehicle. Remove the key. Then try a restart, should be clear of "Transport Mode."

Here is a YouTube video (on a Focus, that shows the sequence.)
2013 ford focus focus ST out of transport mode

Mar 12, 2014 | Ford Escape Cars & Trucks

1 Answer

I need to replace the right rear blinker light bulb. How do I do that ???


Go to this FREE Ford website to view or download the users manual, it will give you step by step instructions on how to do this. There's several proceedures based on which Focus body style you have.
www.fleet.ford.com/maintenance/owners_manuals/default.asp

Nov 11, 2010 | 2004 Ford Focus

1 Answer

How to replace ford ignition switch


Hi,

Thanks for writing to Fixya.com.

Please find a detailed step for removing the ignition switch from a Ford.

http://wiki.answers.com/Q/How_do_you_remove_the_ignition_switch_from_a_Ford_Focus


Thanks for contacting Fixya and please accept the solution if it has helped you.

May 27, 2010 | 2001 Ford Focus

1 Answer

Replacing the agnition switch how to?


SECTION 211-05: Steering Column Switches 2001 Focus Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 09/15/2004 Ignition Switch Removal
  1. Depower the supplemental restraint system (SRS). For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, GENERAL PROCEDURES).
  1. Detach the instrument panel lower panel.
    1. Remove the screws.
    1. Release the fastener.
    e0001946.jpg
  1. Remove the instrument panel lower panel.
    • Disconnect the hood release.
    • Disconnect the data link (DLC) electrical connector.
    e0009940.jpg
  1. Detach the steering column upper shroud.
    • Using a thin bladed screwdriver, release the two clips (one each side).
    e0000671.jpg
  1. Remove the steering column lower shroud.
    1. Release the steering column locking lever (if equipped).
    1. Remove the screws.
    • Remove the ignition key.
    e0000670.jpg
  1. Disconnect the electrical connectors.
    • Disconnect the ignition switch electrical connector.
    • Disconnect the turn signal/flash-to-pass switch electrical connector.
    e0001776.jpg
  1. Remove the ignition switch.
    • Release the clips.
    e0000394.jpg
Installation
  1. To install, reverse the removal procedure.
  1. Repower the supplemental restraint system (SRS). For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, GENERAL PROCEDURES).

2010&c18=modelyear&c20=g17614&c35=wsm%2cignition%20switch%2cs1y%2c211-05%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 01, 2010 | 2001 Ford Focus

1 Answer

How to replace high/low beam switch on 2004 Ford Focus LX?


Should be fairly easy. Make sure to disconnect the positive battery cable. Remove the cover from around the column behind the steering wheel. Should take a star driver to remove the screws holding the cover together. Once the screws are removed pop the cover apart and you will see the multifunction switch on the column, should have two to three screws holding it to the column remove the screws and it should come out pretty easy replace with new one and put back together.

Oct 02, 2009 | 2004 Ford Focus

1 Answer

I have purchased a 2004 1.8 tdci ford focus,I need a spare key!


go on ebay to by the key and then get it cut at like target or walmart...

once you get the new key...

1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works

Aug 10, 2009 | 2004 Ford Focus

2 Answers

2000 FORD FOCUS IGNITION REPLACEMENT INSTRUCTIONS


Your ignition is what supplys your spark pluggs with electricity in order to creat combustion in your engine. Most older cars have distributers, if you drive a focus with a zetec it will have a coil pack. I have a 2002 Focus SVT that I upgraded the ignition system to a full racing system for around $200. What you need to change is the coil pack, spark pluggs and spark plugg wires. You only have to remove about four bolts on the coil pack and it just pulls out.

Jun 16, 2009 | 2002 Ford SVT Focus

2 Answers

Ford Focus 2004 - key won't turn in ignition


these vehicles have a lot of problems with ignition cylinders binding up. It needs to be replaced with an updated cylinder. If you tap on the key with a small hammer or something like it while turning the key you can get it to turn

Dec 14, 2008 | 2003 Ford Focus

Not finding what you are looking for?
2004 Ford Focus Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...