Question about 2000 Daewoo Lanos

1 Answer

My 2000 Daewoo Lanos's Heater/AC was working in all 4 settings (1 low, 2 med, 3 high, 4 super high). Now it only works in setting number 4 and the others just stay off. What could be the problem?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Daewoo Master
  • 1,564 Answers

You have one of two situations. One would be a burned out resistor group within the heater box, this controls the voltage flow to the blower motor. The resistor group is a small(about 1 1/2 inches by 3/4 of an inch rectangular plate made of black or biege plastic with four push on connectors. This is usually located on the passenger side under the dash on the heater box. The other possible location is on the passenger side firewall under the hood Look for signs of burnt plastic first, then remove the two mounting screws and look at the inner parts. Most likely you'll find one , or more of the windings are broken. Thank you, Dana

Posted on Sep 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ac blower motor stopped working


YJ car.
the blower is dead. is that it?
does it blow full speed on high
do you have 12v on terminal A of blower , term B is 0v ground
got that, then the blower is dead.
if not 12v, then the controls are bad.
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

page 47
4 parts to make blow
1: fuse 12 good.
2: switch heater /on off.
3: high, med,low speed, use high, its direct.
4: the blower,
one of those points has no 12v on high,
use a simple voltmeter to find the failed point.

Jan 14, 2014 | 1994 Jeep Cherokee

1 Answer

Why does my heater in my 2000 ford ranger only work on the high setting?


I assume that you are talking about the heater fan?

Your heater FAN has at least 3 settings, and for our purposes we will assume low,med and high

Low and medium run through a resistor High is wired direct
Either your resistor is bad or your fan is
I know it seems wrong that the fan could be shot but it could be pulling so many amps that it won't work in any other mode than high
I just had this happen on one of my trucks
Start with the fan

Apr 06, 2010 | 1998 Ford Ranger SuperCab

1 Answer

Where to recharge ac for 2000 daewoo lanos


The low side fill port is directly below the air cleaner rubber hose by the right shock tower. The high side fitting is on top of the right shock tower along the edge of the fender.

Jul 15, 2009 | 2000 Daewoo Lanos

2 Answers

HEATER NOT WORKING ON MAXIMUM HEAT CUTS OUT LANOS DAEWOO


if you using salt water just clean it every month, because it creates layer so the mission can't show good performance.

Jan 22, 2009 | 2000 Daewoo Lanos

1 Answer

Firing order for 2000 daewoo lanos


CLICK HERE

The order is 1, 3, 4, 2

Looking @ the engine from the front, the cylinders are numbered

1 2 3 4


Thank you for using FiXyA - A FiXyA rating is appreciated!

Jan 21, 2009 | 2000 Daewoo Lanos

2 Answers

2000 daewoo lanos head torque


the 2000 daewoo lanos 1.6L dohc head torque is as follows , step 1 = 18 ft. lbs. , step 2 = 70 degrees , step 3 = 70 degrees , step 4 = 30 degrees . sequence is as pictured .

58bb502.jpg

there ya go , gears to the left , looking at the front of engine .

Jan 09, 2009 | 2000 Daewoo Lanos

2 Answers

Daewoo lanos 2000 car is misfiring and wont run properly firing on cylinders 1 and 4 misfiring


have you changed the ignition wires? perhaps firing order crossed? if not coil pack or ignition wires faulty how do you know it is not "FIREING" on 1 & 4 have you tested it with a spark tester tool???

Dec 23, 2008 | 2000 Daewoo Lanos

1 Answer

Ac won't come one


the compressor cycling swictch has 3 pins and do not know which is the live from the neutral.

Sep 17, 2008 | 2000 Daewoo Lanos

Not finding what you are looking for?
2000 Daewoo Lanos Logo

Related Topics:

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...