Question about 1996 GMC Jimmy

1 Answer

My new TRW upper ball joint did not come with the torque specs for the main nut, should i go with my haynes manuals specs that say 61 ft.lbs. even though this would be a different ball joint than stock. 1996 gmc jimmy 4x4

Posted by on

  • Eliezer Miller May 11, 2010

    is this a oe replacement part or upgrade/modification

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 366 Answers

If your trw balljoint instruction paper doesnt say otherwise go with it.

Posted on Sep 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for ball joints on 2000 gmc jimmy


Upper ball joint knuckle nut 60 ft lbs, lower ball joint knuckle nut 80 ft lbs....mounting nuts and bolts 17 ft lbs

Jul 12, 2014 | 1996 GMC Jimmy

1 Answer

Torque on front ball joints 2000 Honda Passport 2 wheel drive


Lower ball joint specs:
Torque the ball joint-to-control arm nuts/bolts to 85 ft. lbs. (115 Nm). Torque the castellated nut to 108 ft. lbs. (147 Nm).

Upper ball joint specs:
Tighten the mounting bolts to 42 ft. lbs. (57 Nm) and the castellated nut to 72 ft. lbs. (96 Nm).

Feb 28, 2011 | 2000 Honda Passport

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

I need to replace my ball joints. can you give me some tips on how to do this? I have never done this before and i would appreciate some pointers on what i need to do to get the job done. Thank you very...


UPPER BALL JOINTS
  1. Raise and support the truck with jackstands. Remove wheel.
  2. Support the lower control arm with a floor jack.
  3. Remove the cotter pin from the upper ball stud and loosen, but do not remove the stud nut.
  4. Using a forcing-type ball joint separator tool, loosen the ball stud in the steering knuckle. When the stud is loose, remove the tool and the stud nut. It may be necessary to remove the brake caliper and wire it to the frame to gain clearance.
  5. On R-series trucks, drill out the rivets using a 1 / 8 in. drill bit. Remove the ball joint assembly.
  6. On C-series trucks, drill out the rivets using a 1 / 8 in. drill bit to start a pilot hole. Drill out the rivets with a 1 / 2 in. bit. Remove the ball joint assembly using a screw-type forcing tool.

To install:
Installation is the reverse of removal but please note the following important steps.
  1. On R-series vehicles, tighten the ball joint nuts to 18 ft. lbs. (24 Nm).
  2. On R-series vehicles, tighten the ball stud nut as follows:

    1 / 2 ton trucks: 50 ft. lbs. (68 Nm), plus the additional torque to align the cotter pin. Do not exceed 90 ft. lbs. (122 Nm) and never back the nut off to align the pin. 3 / 4 and 1 ton trucks: 90 ft. lbs. (122 Nm), plus additional torque necessary to align the cotter pin. Do not exceed 130 ft. lbs. (176 Nm) and never back off the nut to align the pin.
  3. On C-series vehicles, tighten the ball joint nuts as follows:

    1988-90 models, tighten the nuts to 17 ft. lbs. (23 Nm) for the 15 and 25 Series and 52 ft. lbs. (70 Nm) for 35 the Series. 1991-98 models, tighten the nuts to 18 ft. lbs. (24 Nm).
  4. On C-series vehicles, tighten the ball stud nut to 90 ft. lbs. (120 Nm) on 1988-90 models, 84 ft. lbs. (115 Nm) on 1991-95 models and 74 ft. lbs. (100 Nm) on 1996-98 models.
  5. Install a new lube fitting and lubricate the new joint.
LOWER BALL JOINTS
  1. Raise and support the front end on jackstands.
  2. Support the lower control arm with a floor jack.
  3. Remove the wheel.
  4. Remove the lower stud cotter pin and loosen, but do not remove, the stud nut.



0900c1528008f64b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Remove the lower ball joint using a suitable tool-R-Series shown, C-series similar


0900c1528008f64c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: Use an appropriate tool to separate the lower ball joint from the steering knuckle-R and C-Series


0900c1528008f64d.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 4: Installing the lower ball joint-R and C-Series
  1. Loosen the ball joint with a forcing-type ball joint tool. It may be necessary to remove the brake caliper and wire it to the frame to gain enough clearance.
  2. When the stud is loose, remove the tool and ball stud nut.
  3. Install a spring compressor on the coil spring for safety.
  4. Pull the brake disc and knuckle assembly up and off the ball stud and support the upper arm with a block of wood.
  5. Remove the ball joint from the control arm with a ball joint fork or another suitable tool.

To install:
Installation is the reverse of removal but please note the following important steps.
  1. On R-series vehicles, start the new ball joint into the control arm. Position the bleed vent in the rubber boot facing inward.
  2. On C-series vehicles, force the ball joint into position using a screw-type forcing tool. The ball joint will bottom in the control arm. The grease seal should face inboard.
  3. On R-series vehicles, turn the screw until the ball joint is seated in the control arm.
  4. Lower the upper arm and match the steering knuckle to the lower ball stud.
  5. On C-series vehicles, start ball stud into the knuckle. Install the nut and tighten it to 90 ft. lbs. (122 Nm) on 1988-90 models; 84 ft. lbs. (115 Nm) on 1991-94 models and 94 ft. lbs. (128 Nm) on 1995-98 models. Advance the nut to align the cotter pin hole and insert the new cotter pin. NEVER back off the nut to align the cotter pin hole; always advance it!
  6. On R-series vehicles, tighten the ball stud nut to 80-100 ft. lbs. (108-135 Nm), plus the additional torque necessary to align the cotter pin hole. Do not exceed 130 ft. lbs. (176 Nm) or back the nut off to align the holes with the pin.
  7. Install a new lube fitting and lubricate the new joint.

Jan 15, 2010 | 1996 GMC Sierra

1 Answer

My trw lower ball joint came with torque specs for the mounting bolts to 15ft.lbs each.. My trw upper ball joint came with no specs for the mounting bolts which are smaller bolts than the lowers, how do i...


I've replaced many ball joints, and never used a torque wrench. Just make them tight. If yours are the type with cotter pins, then you make it tight and slip in the cotter pin.

Sep 24, 2009 | 1996 GMC Jimmy

3 Answers

Ball joint installation


Go with what the ball joint specs. Besides only 2 ft.lbs. on a ball joint won't make a difference. But the parts recommendation should be used.

Sep 23, 2009 | 1996 GMC Jimmy

2 Answers

Need to know the torque settings for a 1969 chevy c10 upper and lower ball joints


for a 72 which is the same front end: upper-install new joint torque the bolts that hold it on the a-frame to 45 ft. lbs. then torque the ball stud as follows: 40-60 ft. lbs. plus additional torque to align cotter pin not to exceed 90 ft. lbs. never back off to align cotter pin. then install cotter pin.

May 19, 2009 | Chevrolet Chevy Cars & Trucks

Not finding what you are looking for?
1996 GMC Jimmy Logo

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...