Question about 1996 Mercury Villager

1 Answer

No voltage to air intake senor - 1996 Mercury Villager

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 118 Answers

Sounds like a loose connection or bad ground there not fun to trace but you have to start somewhere you may even have to do some soldering

Posted on Sep 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When i started my madaz b 2300 truck up the engine idle up high and i had to switch the engine off.after that time i had trouble with the engine running ,when i started the engine it idle good for 15


may be you should make a diagnostic and you can do it in a garage or you can do it by yourself if you want to do it by yourself you need some tools and you can find some good ones here: chinasinoy.com

Feb 20, 2013 | Cars & Trucks

1 Answer

Engine stalls going down the road, then starts right back up


Possibly - Mass Air Flow Sensor, poor oxygen mix
Possibly -Air Intake Sensor at Intake manifold, clean with carb cleaner.
Possibly - Crank Shaft Positioning Magnet, not aligning properly
Possibly - Oxygen senors, 1 before catalytic and 1 after it, poor exhaust eventing stemming from clogging catalytic converter
Possibly - Clogging in fuel delivery system starting from fuel pump and ending at intake manifold.

I would check these in that order.

May 27, 2012 | 2000 Pontiac Grand Prix

1 Answer

Intake Air Temperature Senor High Voltage


Your IAT sensor is either defective or the wire going to it had rubbed through and shorting on some metal surface.

Feb 04, 2012 | 2004 Saturn ION

1 Answer

Where is the air temperature senor located on 1994 Subaru Legacy


They are usally in the air intake tube going to the throttle body.

Jan 19, 2012 | Cars & Trucks

1 Answer

MAF sensor code P0102. Changed senor, pcv valve, cleaned egr valve, checked intake filter, connections, etc still get code. Not sure where to look next. 3.8 liter 2002 chevy Impala


Check for vacuum leaks at intake, and snorkel. Moniter short term fuel trims. Check Freeze frame of when code P102 sets. Make sure you are using stock air filter system aftermarket filters cause havoc.

May 13, 2011 | Chevrolet Impala Cars & Trucks

1 Answer

My car will not start, I replaced the starter, replaced the battery 2 months ago, I replaced the mass air flow senor,crank shaft senor and modulator? When you try to start it, it shudders and will not...


That still could be a number of things. Fuel pump, O2 sensor, Ignition coil, etc. A good way to find out if its a fuel or electrical problem is to get a can of starter fluid. Open the air intake and spray a little inside and see if it starts. If it does not, then you have a spark or sensor problem. If it does start, then you have a fuel problem.

Nov 21, 2010 | 2000 Buick LeSabre

1 Answer

It's a 92 Plymouth laser 1.8 none turbo, wont start when cold..will only idle. Once it gets some heat in it, it runs and starts fine. It threw 3 codes, volume Air Flow senor, intake air temperature sensor,...


Hello! system dropped our chat... probe onto the Gray/White and - probe on the Gray/black...Meter set to read 5 volts...start engine...Meter must read less than 1 volt (.85)...Slowly increase throttle...Meter must read 4 volts at full throttle...Voltage must increase smoothly...If it jumps, jerks or acts erratic the TPS is defective....saailer

Sep 15, 2010 | 1992 Plymouth Laser

1 Answer

Where is THE AIR INTAKE SENOR LOCATED


Should be on the air intake tube or in that black box on the right side of engine compartment at front. thats right from cab lookig out windshield.

Sep 11, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

I need to locate the air senor switch in a 2008 ford fusion


The mass air flow sensor is in the air intake tube at the lower left corner of the engine compartment. Please rate this info That will help me THankyou RJ

May 30, 2010 | 2008 Ford Fusion

1 Answer

My service engine soon light came on displayin po170. i have a mitsubishi galant 2000. how do i fix this problem


PO170 is a fuel trim malufunction. On a V6 this applies to the rear cylinder head. Lots of possibilities as fu"el trim" refers to the volume air flow sensor, fuel injector, fuel pressure, engine coolant senor, air intake sensor, barometric pressure sensor, oxygen sensor, intake air leaks, or cracks in the exhaust manifold

Mar 03, 2010 | 2000 Mitsubishi Galant

Not finding what you are looking for?
1996 Mercury Villager Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

fordexpert

Level 3 Expert

5575 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...