Question about 1996 Ford Mustang

1 Answer

I need to know how to replace a head gasket on a 96 mustang gt 4.6

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 58 Answers

This might help you....

http://www.mustangmonthly.com/howto/5892/index.html

Thank you and be sure to rate....

Posted on Sep 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I've got a 99 mercury sable 3.0, replaced all head gaskets and water is still getting in the oil! What could it be and what could I do???


eplacing head gasket, need advice - Taurus Car Club of America ...

www.taurusclub.com > ... > Maintenance and Repair
Apr 3, 2013 - Vehicle is a 1998 Taurus 3.0L, Gen3 Vulcan, used as a daily driver, ...target="_blank">Replacing Head Gaskets On A Ford Taurus 3.0L V6 ... With all that coolant going through the exhaust your O2 sensors are toast. .... Drives: 96 Mercury Sable LS Wagon 3.0 DOHC Duratec .... 1999 Taurus need help.

Nov 23, 2015 | Mercury Cars & Trucks

1 Answer

Huge oil leak on driver side of my 2000 mustang gt


as removing the head this would give you better view of the engine so you may be able to see the oil filter part .Just a thought not leaking from head gasket ,you'll find out when removing head i guess

May 05, 2014 | 2000 Ford Mustang

1 Answer

Getting ready to replace both head gaskets on my 2001 Mustang GT...It only has 40,000 miles though! I am almost positive it's a head gasket issue, likely from cylinder # 3 seeing as I am getting a P0303...


Get a Haynes or Chilton's Manual on your vehicle so you have the correct sequence for removing the head bolts and for putting them back. While you have the heads off and the timing chain loose replace the timing chain and make sure you have the heads resurfaced and valves adjusted. Might as well do all of this at once so you don't have to worry about it doing it in 10k to 20k.

Nov 21, 2010 | 1996 Ford Mustang

1 Answer

I have a 96 mustang gt with a auto trans it


Old fluid and filter, maybe the modulator. Could need tranny service but changing the fluid is cheapest route to start with.

May 01, 2010 | 1998 Ford Mustang

1 Answer

Need to know how to put the top down on 96 mustang dont have manu


First thing to do is put the car in park and then set the parking brake. Next, release the drivers and passenger side handles (located at the top, above your head when you are sitting in the car, where the part of the top meets the windshield) Both handles are black and you simply pull the lever to release the hooks. After both hooks are released, push the button located near the speedometer (should be underneath the speedometer) on the dash and the top motor will engage and begain to retract the top. Hold the button untill the top disapears behing the back seat

Feb 28, 2010 | 2007 Ford Mustang GT California Special...

3 Answers

My 96 mustang gt 4.6L automatic is running like


vacuum leak. it wiil cause a misfire code to be set because too lean from vacuum leak.

Feb 14, 2010 | 1996 Ford Mustang

2 Answers

97 mustang overheating and blowing cold air


Get a compression check to find out if you have a bad head gasket, I have a 96 with the 3.8L that had the same problems at first. then it started to blow out antifreeze thru the expansion tank, the head gasket finally blew the rest of the way going down the highway

Dec 04, 2009 | 1997 Ford Mustang Cobra

2 Answers

My 95 mustang had over heated, has blowing head gaskets and it won't start what do i need to do to fix it?


V6? these are famous for head gaskets and cracked heads. the heads will need to come off and checked over for cracks and repair or replacement by a automotive machine shop.

Oct 22, 2009 | 1995 Ford Mustang

1 Answer

Mustang gas tank removal


yes to do it the right way you should take the tank out of the car empty and rinse out then replace when completly dry

Jun 24, 2009 | 1996 Ford Mustang

1 Answer

I need the torque specs for the intake manifold bolts on a 2001 mustang gt.


Intake manifold-to-cylinder head bolts for 5.0L V8:
Step 1 = 96 in-lbs Step 2 = 16  " Step 3 = 23 to 25  "
Numbers taken from an after market manual, so use at your own risk.

Apr 15, 2009 | 2001 Ford Mustang

Not finding what you are looking for?
1996 Ford Mustang Logo

Related Topics:

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...