Question about 1996 Chevrolet Monte Carlo

1 Answer

Blinkers, hazards, and brake lights don't work, can't find fuse.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 2,007 Answers

Use a test light. Ground it to your door jam, and without removing the fuse, and with the ignition "on", touch each side of your fuses on the metal part that shows through on either side of the amp # of the fuse. You should have power to both sides of every fuse. If there is only power on one side, that's the burnt one.

Posted on Sep 23, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
johnny5846
  • 379 Answers

SOURCE: 2001 dodge neon tail lights inop

looking at your schematics and , you say tail lights don't work , you didn't mention if front parking lights and license plate lights are working , they all come from the same source , a black /yellow wire , a good clue if front work and rear don't , please advise .if fronts work then you have a open circuit somewhere between junction S118 (near breakout for left headlamp) and rear sockets.

Posted on Dec 31, 2008

bunnydawg
  • 5158 Answers

SOURCE: my brake lights and hazard blinkers don't work on my 1990 F350.

you need to replace the flasher relay... it's under the dash board either mounted in the fuse panel (larger then a regular relay) .... or it's just hanging under the dash by inself.

Robert

Please take a moment to rate this solution thanks

Posted on Feb 20, 2009

awcforever
  • 359 Answers

SOURCE: All my blinkers and brake lights stopped working

PO430: Catalyst System Efficiency Below Threshold (Bank 2)

Here is a site that you should go to and further look at the common problems with your catylitic converter, and also your other emissions systems. Hope it helps, and please rate!!!

http://www.discountconverter.com/catalytic_converters_news/news_page.cfm?Key=codes-po420-po421-po430-po431&News=120

Posted on Mar 15, 2009

  • 150 Answers

SOURCE: blinker stopped working, but the hazard lights still work - I think it's a blown fuse but how and where do I fix the fuse

There is 2 different flashers. One flasher for the turn signals and one flasher for the hazards. If you turn on the turn signals and the turn indicator on the dash lights up but doesn't blink, then most likely it is the turn signal flasher that is bad. Good luck.

Posted on May 29, 2009

  • 31 Answers

SOURCE: Brake Lights, Rear Turn Signals, and blinker singal not working

probably needs a turn signal switch

Posted on Jun 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you find short from fuse box on 99 Cadillac Deville works the tail lights, hazard, headlights, blinkers, cruise, brake lights, coolant fans?? All fuses checked good.


Hi Mary ANN , need some clarification ,the fuse's for all these thing's you have listed , the tail lights, hazard, headlights, blinkers, cruise, brake lights, coolant fans are good ? If good what makes you think you have a short ? Explain ! Are these thing's not working ? That wouldn't mean you have a short . You could have a bad ignition switch !

Oct 19, 2015 | Cadillac Cars & Trucks

1 Answer

How can i fix the problem blinkers & hazards don't work


If both the blinkers and hazards are not working, check the fuse block for a blown fuse. Also see if your running and brake lights come on. If they do, and there is no blown fuse, try replacing the flasher unit, usually located either near the fuse block or in the glove box area.

Jun 02, 2015 | 1984 Nissan Sentra XE

1 Answer

Ford f 250


take the plugs and swap them u have the running light plug which are hazards and probly blinkers too. then u have ur tail lights and ur brake lights twwo plugs swap them sounds like ur not geting a got connEction

May 25, 2013 | Cars & Trucks

2 Answers

2005 Ford Focus- Blinkers, Brake lights and hazards don't work -just change the bulbs and they still don't work. Help!


That should be on two different fuses, but everything goes thru the turn signal switch.
The switch might be faulty. A mechanic would check for voltage there.

Jul 11, 2012 | Ford Focus Cars & Trucks

1 Answer

I have a 1990 Mercury Cougar. Several problems...Blinkers, hazards, horn, and break lights are not working. However the break light in the back window comes on when the break is pressed. Checked fused and...


I am unaware of what a "CO" display is.
Now with the blinkers, hazard, horn and brake lights not working that may be the multi funtion switch (blinker switch) that is located inside the column (where the blinker lever attaches).
Obviously the blinker, hazard and horn will all work off of something in the column. Brake lights, you may think a switch on the pedal.

the brake lights do work with that switch but when you have the kind of tail lights where a turn signal light shares the same bulb as a brake light, the brake light is cancelled for the turn signal by running through the multi function switch inside the column.
The third brake light does not blink so its not on that same circuit.

Oct 07, 2011 | 1990 Mercury Cougar

1 Answer

Hazards, blinkers and brake lights do not work.


all this is controlled by a fuse, i can't remember if it's in the dash by the driver door or under the hood

May 05, 2010 | 2001 Dodge Ram 3500 Truck

1 Answer

Brake Lights and Blinkers don't work


try tapping the hazard switch on and off a bunch of times fairly hard. these switches have a tendency to go bad and neither the hazards or turn signals will work

Dec 10, 2008 | 1999 Ford F350 Regular Cab

Not finding what you are looking for?
1996 Chevrolet Monte Carlo Logo

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...