Question about 1992 Honda Accord

2 Answers

Jack stand spots?

Where are other places I can place the jack stands, besides the 4 points where you'd jack to change the tire? I can jack the car then place the stand in the same place...Help me out...Thanks.

Posted by on

  • 1 more comment 
  • aaronjram Sep 23, 2009

    Do you know where specifically? I just wanna be sure...

  • aaronjram Sep 23, 2009

    Do you know where specifically? I just wanna be sure...

  • aaronjram Sep 23, 2009

    Do you know where specifically? I just wanna be sure...

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 299 Answers

The stands can also be placed on the sub frame

Posted on Sep 23, 2009

  • Eliezer Miller Sep 24, 2009

    anywhere near a mount

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 521 Answers

That is the preferred place designed by the manufacturer

Posted on Sep 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Put jack stands uder a 2001 Lincoln LS


place the trolley jack under the front cross member . (The big bit that connects the side frames under the sump). Lift as high as possible and place the jack stands under the chassis ( moulded rails ) where the sub-frame meets . Then place the trolley jack under the rear diff and lift as high as possible Place the jack stands under the chassis at the front of the springs or track rods By using these positions you will have the cabin securely jacked up with all the wheels free to remove or to work on. Before going under try rocking the vehicle hard to ensure that it will not move off the stands.

Mar 15, 2014 | Cars & Trucks

1 Answer

Where do i place the floor jack if the safety stands are going to be supporting by the frame


operators guide , shows jack points, (under change tires)
or
FSM
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

on the axle tubes.
or the frame.
do not jack up to suspension points, or any swaybar /track rods.

Jan 31, 2014 | 2000 Jeep Grand Cherokee

2 Answers

A womp womp womp noise in the rear, tires are good, brakes look good, wheels are not warped, just had them balanced?


Go to a place that has a good smooth parking lot and a wooden private fence. Open all your windows and drive the car slowly as close as possible along the fence in order to pin point where the sound is coming from. The sound will echo back from the fence and will make it easier to pin point the area where the womp womp sound is coming from. Next thing you can do is lift the car up and place it on four jack stands in case you have a front wheel drive. If you have a front wheel drive and your car is on four jack stands, place you gear in nuetral and spin each rear tire separately to see which one is making the noise. Keep in mind that it might be a wheel bearing or if it a rear wheel drive and on four jack stands have someone drive it slowly while you listen for the noise. Some rear wheel drive differentials can make this noise if it is low on differial oil. Be very careful that the jack stands are on solid and making good contact with the car frame and flat on the pavement. Don't place yourself where the car can fall and hit you or run in to you. Good luck.

Dec 03, 2012 | 2002 Porsche Boxster

1 Answer

I want to change the oil in a 1998 Ford Contour SVT. I know the jack points that are to be used for changing a tire, but that doesn't do it for me, as I only have one jack and no jackstands (yet). The...


Lift the car on the side you need to work by using the automobile jack. Place a jack stand under the Ford near the jacking point and raise it so the jack stand can be placed under the frame.

zjlimited_1329.jpg

Hope this helps.

Jun 01, 2011 | Ford Contour Cars & Trucks

1 Answer

I own a 2000 toyota prerunner. My question regards changing a tire, both front and back. I can't tell where to place the jackstand. I see no "flat" areas ar "marked" areas to place...


In the front, place your jack stands on the stabilizer bar bracket that is bolted to the frame...
in the rear, put the jack stands on the rear end, closes to the outside as you can get...
Hope this helps ??

May 26, 2011 | 2000 Toyota Tacoma PreRunner

1 Answer

How to remove the starter


Welcome to Fixya

Here's the procedure on how to replace/remove the starter.

#1
Loosen the negative battery terminal on the car and pull the terminal away from the battery. Place the wheel chocks behind the rear tires.

#2
Jack the car using the automobile jack and place a jack stand under the frame near the jacking point. Raise the jack stand to the frame.

#3
Remove the three bolts that hold the starter to the engine using a socket and ratchet. Remove the starter away from the engine so you can gain access to the wires.

#4
Remove the main wire from the starter using a wrench to remove the nut and then unplug the wire harness.

#5
Pull the old starter away from the engine and put the new one into place. Reconnect the wires by plugging the wiring harness back in and securing the main wire back to the post, tightening the nut with a wrench.

#6
Push the starter into place on the engine and start all three bolts by hand. Tighten the bolts using a socket and ratchet.

#7
Remove the jack stand from under the car and lower the car back to the ground. Start the car to test the installation.

Thank you for using Fixya!

Dec 20, 2010 | 1996 Chrysler Concorde

1 Answer

Where do i place a jack stand on a 1995 Jeep Grand Cherokee?


Hope this helps and please don't forget to rate...thanks!

Jacking points on all Jeep vehicles



c17hydro_1.gif

Your Jeep was supplied with a jack for emergency road repairs. This jack is fine for changing a flat tire or other short-term procedures not requiring you to go beneath the vehicle. Do not attempt to use the jack on any portions of the vehicle other than specified by the vehicle manufacturer. Always block the diagonally opposite wheel when using a jack.



c17hydro_2.gif

Placing a floor jack under the front frame rail



c17hydro_3.gif

Placing a floor jack under the rear frame rail at the leaf spring shackle. It may be necessary to place a block of wood between the frame rail and the jack



c17hydro_4.gif

Supporting the front of the vehicle with jack stands placed under each frame rail


A more convenient way of jacking is the use of a garage or floor jack. You may use the floor jack at the specified points in following the illustrations.

Never place the jack under the radiator, engine or transmission components. Severe and expensive damage will result when the jack is raised. Additionally, never jack under the floorpan or bodywork; the metal will deform



c17hydro_5.gif

Support the rear of the vehicle using jack stands placed underneath each side of the rear differential (inset photo)

Nov 04, 2010 | 1995 Jeep Grand Cherokee

1 Answer

General directions on how to change the front brakes on a Toyota Supra, 1987.


Buy brake pads.
loosen lugs
Jack car, place on jack stand
turn wheel so front of tire is pointing out.
remove tire
remove caliper (two bolts on back side of caliper
slide caliper off rotor.
(if rotor is damaged, see about having it turned or replaced)
take pads off caliper
open hood and remove cap to mater cylinder reservoir
using special tool (or C-clamp and something to protect piston) push the piston back into the caliper fully.
place new brake pads on caliper.
fit caliper on the rotor
Secure caliper to wheel with bolts
replace wheel
remove jack stand
remove jack
tighten lugs on wheel
replace hubcap
start engine (do not drive yet!!!!!)
pump brake pedal until it tightens up
observe reservoir on master cylinder (fill if needed)
replace cap
pump brakes again
take out for a test drive.

good luck and don't forget to vote!!!

Oct 11, 2010 | 1987 Toyota Supra

1 Answer

The function that rsiaes and lowers the vehicle doesn't work,


Lifting

The following instructions must be carried out before raising the vehicle off the ground.

  • Use a solid level ground surface.
  • Apply hand brake.
  • Select 'P' on automatic gearbox selector.
Note: If the propeller shafts are to be removed, reference must be made to the relevant operation. To avoid damage occurring to the under body components of the vehicle the following jacking procedures must be adhered to.

DO NOT POSITION JACKS OR AXLE STANDS UNDER THE FOLLOWING COMPONENTS:
  • Body structure other than approved jacking points
  • Bumpers
  • Fuel lines
  • Fuel tank
  • Brake lines
  • Front or rear suspension arms
  • Transfer box
  • Steering linkage
  • Front or rear differential units
  • Engine sump
  • Automatic gearbox
NOTE: For certain repair operations, it may be necessary to support the engine under the sump. In this case, a block of hardwood or a rubber block should be positioned on the jack lifting cup to protect sump. Vehicle jack
The jack provided with the vehicle is only intended for use in an emergency, for changing a tyre. DO NOT use the jack for any other purpose. Refer to Owner's Handbook for vehicle jack location points and procedure. Never work under a vehicle supported solely by the vehicle jack.

Hydraulic jack
A hydraulic jack with a minimum 1500 kg, (3,300 lbs) load capacity must be used.

WARNING: Do not commence work on the underside of the vehicle until suitable axle stands have been placed in their correct position. Always chock the wheels when jacking. The handbrake may be ineffective when the wheels are off the ground. Raising and supporting the vehicle
To assist in raising the vehicle, jacking points are provided as shown in the following illustrations.

Raising the front of the vehicle
Apply handbrake, select 'P' on automatic gearbox selector and chock rear wheels.
Axle stand positions - front

Raise vehicle to enable axle stands to be positioned under, either, the front sub-frame, or the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.
Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack.
Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Raising the rear of the vehicle
Select 'P' on automatic gearbox selector and chock front wheels.

WARNING: Always chock the front wheels when jacking the rear of the vehicle.

Axle stand positions - rear

Raise rear of vehicle to enable axle stands to be positioned under the rear sub-frame. Alternatively, the axle stands may be positioned under, either, the recommended customer jacking points or the front mounting points of the rear sub-frame.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If any damage occurs to the washers on the front mounting points of the rear sub-frame, then the washers must be replaced. Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack. Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Wheel-free lift
The following warning must be read before attempting to lift the vehicle.

WARNING: The vehicle cannot be supported safely in a wheel-free condition using the wheel-free facility of a four post ramp, and under no circumstances must this method be employedA wheel free condition may only be achieved on a four post ramp by raising each end of the vehicle and positioning axle stands beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox. WARNING: The front and rear suspension lower arms must NOT be used as lifting / jacking points. Alternatively, support the vehicle on an approved two post lift with the arms of the lift beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between the lifting equipment and the jacking points to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.

Oct 04, 2009 | 2003 Land Rover Range Rover

1 Answer

Jack stand


jack stands most times are placed under neath the axles however in your case the stands should be placed behind the front wheels on the spot where you whould place a regular jack if let's say you were changing a tire. if your working on the rear of the vehical you should put them under each side of rear axle.

Aug 27, 2008 | 1999 Pontiac Sunfire

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

699 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...