Question about 1989 Toyota Pickup SR5

1 Answer

Just got the clutch on my 89 toyota pick-up replaced and now it pops out of first gear and doesn't go into third gear.. any ideas what it could be?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 73 Answers

It sounds like the shifter was installed incorrectly.
The transmission does not need to be removed just the shifter from the top pf the trans needs to be installed correctly

Posted on Sep 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What allows clutch to slip so much to not move car.


-Possibly time to replace new clutch.

Good luck


mai

Nov 10, 2014 | 1990 Toyota Camry

1 Answer

HJ75 toyota 89 troupie diesel 5 speed...Have had new clutch kit installed recently to rectify slipping. Main oils eal & input shaft seal replaced also. Problem is now I have an almighty transmission...


I have seen somethings similar to what you describe, 1 - the rear tailshaft was slightly loose, 2 - the yoke the tailshaft bolts to on the gearbox is held on by a big nut and when this is loose or not done up tight enough can clunk. More noticeable in the lower gears because of the high torque.

Let me know what you think.

Jul 18, 2011 | Toyota Land Cruiser Cars & Trucks

1 Answer

Ran out of gas on 89 Acura Integra, car won't re-start


pull tow the car and pop the clutch to jumpstart. when u run out of gas sometimes u get an air bubble in the line and it has to be pushed up to a certain speed then pop the clutch in second or third gear and it should start.

Jul 28, 2010 | 1989 Acura Integra

1 Answer

1990 Toyota PICK UP SR5 V6, when in gear and start releasing clutch pedal, truck starts moving forward with slight jerking. As soon as I give it gas, it starts to **** harder, forcing me to shift into 2nd...


Sounds like it is a clutch issue. Have the clutch plate checked or check the clutch and friction plates. I know it sounds strange but In reality we always press teh clutch all teh way in to shift. But going from 2nd to third you actually don't have to. Going from 3rd to 4th is even less of a distance. It may be a problem between the clutch and friction plates depending on when you last had them changed and adjusted.

Jun 28, 2010 | 1990 Toyota Pickup

1 Answer

Clutch problem


you still have air in the system very hard to bleed is the slave and master dry look under the dash at the master where it comes through the fire wall to see if it is wet some times you need to power bleed them

Feb 02, 2010 | 1991 Toyota Pickup

1 Answer

Clutch issue? 89 toyota PU 4x4 V6 150,000 miles


Yep, you got it. Assuming spring tension on pressure plate feels normal (you should know with 150k mi) then the clutch disk is worn. Time for replacement.

Jun 22, 2009 | 1991 Toyota 4Runner

1 Answer

82 toyota pu stuck in third gear. any ideas?


pull the shifter out and check for bent and worn parts, most likely the shaift rails are worn out and it is stuck between gears.

Apr 30, 2009 | 1983 Toyota Pickup

1 Answer

My '89 Silverado 2500 won't stay in gear and the clutch sticks.


if you havnt already, sounds to me like its time to replace clutch

Apr 22, 2009 | 1989 Chevrolet Silverado 2500

3 Answers

89 toyota 22re sr5 ext cab 2wd slips out of 1st and 3rd its a 4cyl fuel injection


First things first, It sound like your tranny may of had its better days. Yes your sincronisers maybe worn out. but some toyota trannys have a shifter that has a broken seet and/or worn bussing.
this is what it looks like.


da354d7.jpg

This is the bushing.

f6a7ff7.jpg

These parts are in the top of the tranny where the shifter goes in i would start there. If it is fine then start thinking about a rebuild. I hope this helps. I believe these parts a less than 20$.

Marlin Crawler sell them.

Jan 22, 2009 | 1989 Toyota Pickup SR5

1 Answer

1989 Toyota Camry


Hi,

On an 89 Toyota Camry with manual transmission, two possible reasons:
  • clutch;
  • release bearing
Try bleeding the clutch on the slave cylinder. If this does not prove to be corrective, you may have to have the transmission/clutch checked/repaired/replaced. In some instances, it could just be a sticking release bearing or clutch fork.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jul 25, 2008 | 1989 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...