Question about 1999 Dodge Ram 2500 4WD

Open Question

2000 Dodge Ram 2500 8.0 V10 running rough misfiring lightly and now there is gas smell coming out of the exhaust I have put new plugs and wires in and replaced the o2 sensor on the passenger side The catalitic converters are not plugged they have been removed

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tjspear
  • 66 Answers

SOURCE: i put seafoam in a 01 mits diamante(oil) drove fine now has code

if you have a coil on plug system, or a waste spark system.... swap coils and see if the miss follows the coil.... voila... that'll fix it.

Posted on Sep 12, 2009

Bloomingidoi
  • 49 Answers

SOURCE: engine misfiring/fuel coming out exhaust

Sounds like you may need to inspect and replace your fuel line from front to rear. no other reason for your problem.

Posted on Nov 29, 2008

  • 47 Answers

SOURCE: 2002 Alero check Engine light Codes P0132, P0137

Code P0132 is O2 sensor voltage high bank1 sensor 1, P0137 is O2 sensor voltage low bank 1 sensor 2, P1189 indicates a fuel control problem bank 1. It could be either the O2 sensors or a convertor. Could also be intake manifold gaskets. GM had a lot of problems with the lower intake gaskets leaking on the 3.1 and 3.4 engines that was linked to their Dexcool coolant. In fact they just lost a class action lawsuit about it. check with the dealer and see if the intake problem has been taken care of. Hope this helps.

Posted on Jan 18, 2009

  • 69 Answers

SOURCE: no power rough idle car stalls strong exhaust smell

have you done a reaaly good tune up on the car? I would suggest replaceing the idle air control valve first, the a really good set of plugs and wires. I would also reccomend that you check the fuel regulator to be certain it is getting the required vacum to operate the release valve and let the fuel flow back into the tank.

Posted on Apr 01, 2009

ghost45
  • 1280 Answers

SOURCE: after engine heats up it stumbles and will not

Bench test your throttle position sensor... could be faulty.

Posted on Sep 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a mazda mpv 2000 minivan.problem code p0301 misfire detected cylinder#1


I'd check #1 spark plug.
Usually a misfire code "fix" is a spark plug, spark plug wire, or a coil pack / distributor.
Keeping it simple...I'd go with the spark plug first and then look at the condition of the wires.

Hope this helps...

Aug 28, 2011 | 2005 Mazda MPV

1 Answer

2001 dodge ram 2500 v10 oil pressure drops to 0 then back up


you need to put an oil pressure gauge on it and see what happens.what you will find is that the sender unit is no good.

May 18, 2010 | 2001 Dodge Ram 2500 Truck

1 Answer

1999 dodge 2500 5.9L gas #4&#7 randam misfire


I would start with a new set of plug wire and plugs.

Oct 25, 2009 | 1999 Dodge Ram

2 Answers

03 Dodge Ram 1500, P0307 code, check engine light


Try this:

Dodge 1995-1999 V8 spark plug wiring.

http://dodgeram.info/tsb/1998/18-48-98/18-48-98-v8.htm

Jul 01, 2009 | 2004 Dodge Ram 2500

1 Answer

Engine light comes on - Code shows P0300 and then


OBD II 300 Random/Multiple Cylinder Misfire Detected

When the misfire monitor detects a misfire, it will trigger the check engine light with the specific cylinder number as the last digit in the P030X code. For instance cylinder 1 misfire is P0301, cylinder 2 is P0302 etc. In this case we have either multiple cylinders misfiring, or the computer simply can't determine the specific cylinder, and as such we are left with the P0300 in computer memory.

Possible Causes:

Fuel injectors, related wiring, sensors and computer issues
Running out of gas, or poor fuel quality
Evaporative emissions system (EVAP) concerns: fuel vapors leaking into engine
Incorrect Fuel Pressure
EGR system concerns: leaking EGR valve or restricted ports
Base engine concerns: low compression, valve train problems and timing issues
Ignition system concerns including, but not limited to:
Faulty spark plugs
Faulty coil or related wiring
Ignition module or related wiring issues
Ignition related sensor faults or wiring issues

Apr 04, 2009 | 1996 Dodge Ram 1500 Club Cab

1 Answer

2000 SS camaro lacking power producing overwhelming exhaust


did you put the platinum plugs back in.get a noid light test the injector wires make sure they are working . when you hook noid light up these should have a steady blink .if light dont blink just light up.you got pcm problems .if you get no lights you have open wire.besure to check ignition coils that control those misfiring cylinders.

Feb 23, 2009 | 2000 Chevrolet Camaro

2 Answers

Engine misfiring/fuel coming out exhaust


Sounds like you may need to inspect and replace your fuel line from front to rear. no other reason for your problem.

Nov 29, 2008 | 2001 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

596 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...