Question about 2003 Chevrolet Malibu

1 Answer

I need the diagram to put the spark plug cables

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,970 Answers

2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
i need the diagram to put the spark plug cables - 74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 i need the diagram to put the spark plug cables - 9313fa7.jpgrless ignition system
9313fa7.jpg


2c9i need the diagram to put the spark plug cables - d929c16.jpglass=


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distribui need the diagram to put the spark plug cables - 09e9db9.jpgition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Posted on Sep 23, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

airjer995
  • 5332 Answers

SOURCE: I need the diagram for 2000 Saturn SC to put the

The cylinders from the passenger side to drivers side are 1-2-3-4 The coils from passenger to drivers side are 4-1-2-3 Match up the coil number to the cylinder number and you should be running in no time.

Posted on Oct 16, 2011

  • 56 Answers

SOURCE: I need a diagram for a spark plug wires on a 99'

start with the serpentine belt side of the car (passenger) the first plug hole will be #1 then 2-4 as you work your way to the drivers side as Im guessing this is a 4 cylinder. The coil pack on the top of the engine has all the plug wires coming out of it and should be numbered 1-4 go accordingly from there.

Posted on Jan 04, 2010

  • 5 Answers

SOURCE: I think have put my spark plug cable wrong. I need

Firing order on both 2.8 and 3.1

1-2-3-4-5-6

1-3-5 at rear of engine

2-4-6- front of engine

Hope this helps!

Posted on Mar 05, 2011

  • 290 Answers

SOURCE: distributor cap cables diagram tahoe 95

http://autorepair.about.com/library/firing_orders/bl-fo-3711.htm

Posted on Apr 01, 2009

emissionwiz
  • 75797 Answers

SOURCE: i need a wiring diagram for spark plugs

here it is.
27fb7d8.gif

Posted on Apr 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need the diagram to put the spark plug cables


In most cases, the cylinder numbers are stamped on the dist cap.
The firing order is 1-2-3-4-5-6 and the odd number cylinders are next to the firewall.

Feb 26, 2013 | 2000 Nissan Quest

1 Answer

1989 volvo 740 spark plug installation


simple if you are familiar with engines remove 1 spark plug wire at a time unscrew spark plug replace with new one put wire back on that plug and continue to the next wire remember do one at a time should only be four plugs on that vehicle

Nov 21, 2011 | Cars & Trucks

1 Answer

I think have put my spark plug cable wrong. I need a diagram to find out which position they go. Thank you


Firing order on both 2.8 and 3.1

1-2-3-4-5-6

1-3-5 at rear of engine

2-4-6- front of engine

Hope this helps!

Mar 05, 2011 | 1995 Oldsmobile Cutlass Supreme

1 Answer

How do I install a distributer on 1998 vortec engine. old distributer missing


Hi: To Install the Distributor Correctly, 1st thing to do is Remove your #1 Spark Plug assuming it will turn over have someone Turn the Key Off and On in Short Intervals.Either put a Compression Gauge in the #1 Spark Plug HoleOr the Old Fashion Way Works as well just put your Finger in the #1 Plug Hole.As your Helper Cranks the Engine On -Off On -Off.Not A Continuous Crank.When You Feel Air Pressure or See gauge Come up.TYhats when your Engine is a The compression Stroke.Now you Can Drop the New Distributor in its Hole.NOTE: You'll need a Spark Plug and Timing Diagram to See the Position your Distributor ROTOR Line it up to where the Diagram Shows your #1 Spark Plug Wire Will go in the Distributor Cap.If the Distributor Rotor is Not n That Position Your goning to Get Either Back Firing engine May Not Even Stsrt, To This Is Crucial. After The Know that you have The Distributor Droppped The Right position you'll need to Put Gap your Plugs at the Correct Specs, With All Plugs in Now You'll need to Put New Plug Wires on .And They MUST be in the correct order.Sitting inside your Vehicle #1 Plug is the Front Plug on the Drivers Side Next is #3 plug Next is #5 and Your Back Plug is Number 7,On the other side Passenger Front Plug is #2 next #4 Next is #6 and the Back is #8 Assuming you know have your Distributor Dropped in The Proper Position, Put the #1 Spark Plug Wire on the Front Spark Plug (Drivers Side) The Spark Plug Firing Order in Your Engine is 1-8-4-3-6-5-7-2 Clockwise So the Next hole after you have #1 Plug and Wire on And Distributor In Correct Position on COMPRESSION STOKE, Going Clockwise you next wire will be your #8 Position in The Cap And it wil go to the Back Spark Plug on The Rear Spark Plug on Passenger Side. NOTE: Drivers Side Spark Plugs on the Drivers Side Front to Back are Your Odd Numbers 1-3-5-7 Pasenger Side is Your Even Numbers From The Front is #2-4-6-8 Is The Rear PLug .

Heres a Diagram of your Spark plug Positions

Front of Engine
1 2
3 4
5 6
7 8

Hope This Will Get You Going. Let me know The Quality of Help and Solution I've Given You By Voting on It.And May Can Also Send a Testamony
From d_hubbs

Jun 03, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

How do i put new spark plugs in a nissan 1998 altima. digram would help. I removed the wire set before memorizing the order they were in.


I can't tell if you need to know how to replace the spark plugs or just need the wiring diagram, so i'm giving you a link to a "how to" video.
http://www.wonderhowto.com/how-to/video/how-to-replace-spark-plugs-203687/

Since you didn't memorize the wiring order, here is a diagram...



2899006.gif

Sep 13, 2009 | 1998 Nissan Altima

2 Answers

Changing spark plugs - need to remove intake manifold and should change gaskets...which ones?


To change a spark plug. 1.Disconnect the wire attached to the spark plug it would be wise to do only one at a time! 2.Take a long socket that will fit the spark plug 3.Attach to the socket wrench and turn counter clockwise until off. 4. Put the new spark plug in and hand screw until tight then turn the socket wrench clockwise until completely tight usually 1 1/2 turns. 5.Then reconnect the spark plug wire. Easy as that. Repeat steps 3-5 for the rest and remember ONE PLUG WIRE AT A TIME!

Sep 02, 2009 | 2005 Ford Escape

1 Answer

Timing chain gear marks up or together and spark plug diagram wir


put the dots together, pull out num 1 plug bring num 1 piston up too top dead center on compression stroke,

Mar 05, 2009 | 1991 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
2003 Chevrolet Malibu Logo

10,157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...