Question about 2002 Toyota 4Runner

Open Question

P1126 code 02 4Runner. Replaced throttle body

P1126 code on 02 4Runner. Replaced throttle body since P1126 indicated Magnetic Clutch Circuit and can not purchase just the throttle motor/clutch circuit. If I disconnect the battery and wait a few minutes then reconnect, I can drive for a few miles with no problems. However, after a few miles, engine lights come on, pedal goes limp and P1126 pops back up.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 42 Answers

SOURCE: RE: code b1181open circuit in 2nd squib circuit

The problem probably is in the contacts of the spiral cable Where it is plugged in. if so, the part will have to be replaced. it is pretty easy to do if you can get the steering wheel off, pretty much just unplug it, and remove the clip that holds it to the steering shaft

Posted on Dec 30, 2008

Ad
  • 496 Answers

SOURCE: clutch pedal stays on floor when released

check the helper spring on the clutch pedal. You'll have to get down in the driver's footwell and using a flashlight look at the mechanism while you push the pedal down (and pull up). If the spring isn't missing or broken and everything looks okay, then change the clutch master cylinder. The piston in the cylinder is probably binding due to corrosion in the bore. I have an 1986 and had the same problem. Changing the clutch master cylinder fixed it.

Posted on Feb 22, 2009

  • 1861 Answers

SOURCE: Clutch pedal sometimes engages when near floor

Hi. Let me try to lend you a bit of assistance, also.
My fellow expert Benimur is very correct with his input to you.

But...Air does not get into your clutch hydraulics unless the fluid has leaked out at some point. As long as the cylinders and tubes are intact, I would doubt that air is the issue. Short of pulling the transaxle, and inspecting the clutch, there is really no other way to determine your issue properly.

Personally, I think that you haven internal problem with the clutch assembly. It could be worn fingers on the clutch plate, a worn clutch disc, or something as simple as the throwout bearing is hanging up on the input shaft collar.

If Beni's suggestions does not help, you are going to need to pull the trans off, and inspect the clutch items mentioned above.

Thanks for choosing FIxYa, we wish you the best of luck; let us know how it turns out.

Posted on Mar 04, 2009

  • 1596 Answers

SOURCE: I am wanting to know

LIMP MODE ? I am CONFUSED With this Term. I Have Researched this On AllData and Found NO Such Term Used in My Resources and Have Not (in 30 yrs ) Heard this Term used If you Could Elaborate a Little More and Also Give the Model & Eng Size this Would Help Us Also.
there is Engine sizes>> 2.0 L, 2.3L ,2.5L .& 3.0L along with the Different Models. I / We Need A Little More DETAIL in your Explination of SYMPTOM you are Having with your Vehicle. I / We Woule Like to Help in a Fast and Eficient Manner with your Help We CAN Do This THANK YOU.
,Also Sorry to Take up too much Time Here

Posted on Nov 09, 2009

Danniboi
  • 1098 Answers

SOURCE: what is throttle control motor relay circuit for

This is the electronic control module to keep the idle of the revs correct it also allows the correct amount of fuel to air mixture the car needs to run. some are called EGR some are ICV idle control valve

Posted on Jan 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code P1126 Chrysler Aspen 2007


Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
P1126 Chrysler OBD Code Description
Throttle Control Motor Relay Circuit Open is one of the definitions for the P1126 Chrysler; however your vehicle's manufacturer may have a different definition for the P1126 Chrysler code. Please check below for your specific make.
P1126 Chrysler Information for specific makes
Locksmith Hamburg NY 716 646 8383 24 Hour Locksmith In Hamburg NY

Aug 04, 2016 | 2007 Chrysler Aspen

1 Answer

Efi relay what does it turn on when key not on. i have to pull relay so it wont drain my battery i also got some codes p1126 and p0308 just recently


With the key off the Main EFI relay shouldn't be powering anything up . The EFI relay is energized by the ignition switch , if it is the EFI relay you here clicking ,you could have an ignition switch problem . It can't have anything to do with the fuel pump , because it has it's own relay down stream from the EFI relay . This is just an educated guess , from my thirty + years experience. The only way to tell for sure is test . I suggest you go to you tube an check out some videos on basic electrical trouble shooting . An how to do a parasitic draw testing an go from there .Also go to www.bbbind.com/ for free wiring diagrams to look at what all is involved in that circuit . Get a DVOM - digital volt ohm meter.

P01126 has to do with electronic throttle control . OBDII Code P1126 TOYOTA Magnetic Clutch Circuit Malfunction HelpForCars net I strongly suggest you take this to a ASE certified repair shop or the Toyota dealer

Dec 10, 2015 | 2000 Toyota Tundra

2 Answers

Location of throttle control motor relay


Replace the coolant thermostat. The code is different on a Nissan and actually refers to a thermostat fault. Replace the thermostat and clear the codes, you're fixed

Mar 03, 2015 | 2000 Nissan Altima

1 Answer

2001 Jaguar xtype 2.5 v6 Fault codes p1725 and p1126 Any ideas????


It appears this is a common but expensive problem:
P1126 Throttle Position (Narrow Range) Sensor Circuit Malfunction
P1725 Insufficient Engine Speed Increase During Self Test
The codes were here:
Jaguar OBD II Trouble Codes

Try searching for x-type throttle position sensor, this seems to be your issue.

Jun 14, 2014 | Cars & Trucks

1 Answer

I have a 2000 Lexus gs400 check engine codes 1126 and 440 came up what does that mean?


the p0440 and p1126? if so, the p0440 means Evaporative Emission Control System, and the P1126 means Throttle Position (Narrow Range) Sensor Circuit Malfunction.
_______________
VAS 5054A With OKI Chip

May 02, 2013 | Cars & Trucks

1 Answer

Nissan codes


code p1126 refers to Thermostat stuck open---- except maxima 2002 causes ---wiring---thermostat---ECT sensor
code also refers to throttle motor--open circuit---maxima 2002 causes ---wiring---throttle motor---throttle motor relay--ECM. Select you vehicle and replace unit applicable to it.

Mar 30, 2013 | 2001 Nissan Frontier Crew Cab

2 Answers

I have on 01 xterra-service engine light on-codes P1126 & P0325. I think the battery is about to go,could it be realated to codes? Otherwise what do the codes mean? Appreciate any help


Your battery has nothing to do with these codes. Your vehicles computers have detected a malfunction or failure in the system. This triggers these codes and sets your check engine light. Below I have listed the code meanings and some repair solutions.

P1126 - Throttle Position (Narrow Range) Sensor Circuit Malfunction.

Power supply for the throttle control motor is provided to the ECM via throttle control motor relay. The throttle control motor relay is ON/OFF controlled by the ECM. When the ignition switch is turned ON, the ECM sends an ON signal to throttle control motor relay and battery voltage is provided to the ECM. When the ignition switch is turned OFF, the ECM sends an OFF signal to throttle control motor relay and battery voltage is not provided to the ECM.

Possible Causes For P1126:
- Harness or connectors (Throttle control motor relay circuit is open)
- Throttle control motor relay


P0325 - Knock Sensor Circuit Malfunction

The knock sensor is attached to the cylinder block. It senses engine knocking using a piezoelectric element. A knocking vibration from the cylinder block is sensed as vibrational pressure. This pressure is converted into a voltage signal and sent to the Powertrain Control Module (PCM) or Electronic Control Module (ECM).

Possible Causes For P0325:
- Knock sensor circuit short to ground.
- Knock sensor circuit short to power.
- Knock sensor circuit open.
- Damaged knock sensor.
- Damaged PCM or ECM

Possible Solutions:
- Repair or resecure harness or connector
- Replace knock sensor Bank 1 (Bank 1 if applicable)
- Replace PCM or ECM

The P0325 DTC is a very common problem with Nissan vehicles. On most Nissan vehicles the knock sensor is located on top of the engine block.

knock_sensor_infiniti.gif

Jan 20, 2011 | 2001 Nissan Xterra

1 Answer

Nissan altima 2000 with engine service light on. fault codes per mechanic p0325 and p1126. But he said mass air flow sensor malfunction. is this right?


p0325 is, ignition system or misfire, could be plugs, wires, or a bad coil. p1126 throttle control motor relay curcuit open.P1126 Power supply for the throttle control motor is provided to the ECM via throttle control motor relay. The throttle control motor relay is ON/OFF controlled by the ECM. When the ignition switch is turned ON, the ECM sends an ON signal to throttle control motor relay and battery voltage is provided to the ECM. When the ignition switch is turned OFF, the ECM sends an OFF signal to throttle control motor relay and battery voltage is not provided to the ECM. possible cause, Harness or connectors (Throttle control motor relay circuit is open Throttle control motor relay.

May 07, 2010 | 2000 Nissan Altima

1 Answer

I have problem with code 1126 (toyota 4 runner 2001


Manufacturer Specific Codes

P1100
BARO Sensor Circuit - Read Our Article on Automotive Circuit Testing For Help With This Toyota Check Engine Light Code

P1120 Accelerator Pedal Position Sensor Circuit - Read Our Article on Automotive Circuit Testing For Help With This Toyota Check Engine Light Code

P1121 Accelerator Pedal Position Sensor Range/Performance Problem

P1125 Throttle Control Motor Circuit - Read Our Article on Automotive Circuit Testing For Help With This Toyota Check Engine Light Code

P1126 Magnetic Clutch Circuit

P1127 ETCS Actuator Power Source Circuit

P1128 Throttle Control Motor Lock

P1129 Electric Throttle Control System

P1130 Air/Fuel Sensor Circuit Range/Performance (Bank 1 Sensor 1) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code - More Related Information

P1133 Air/Fuel Sensor Circuit Response (Bank 1 Sensor 1) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code

P1135 Air/Fuel Sensor Heater Circuit Response (Bank 1 Sensor 1) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code - More Related Information

P1150 Air/Fuel Sensor Circuit Range/Performance (Bank 1 Sensor 2)

P1153 Air/Fuel Sensor Circuit Response (Bank 1 Sensor 2) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code

P1155 Air/Fuel Sensor Heater Circuit. (Bank 1 Sensor 2)

P1200 Fuel Pump Relay Circuit

P1300 Igniter Circuit Malfunction - No. 1

P1305 Igniter Circuit Malfunction - No. 2

P1335 No Crankshaft Position Sensor Signal - Engine Running

P1349 VVT System

P1400 Sub-Throttle Position Sensor

P1401 Sub-Throttle Position Sensor Range/Performance Problem

P1405 Turbo Pressure Sensor Circuit

P1406 Turbo Pressure Sensor Range/Performance Problem

P1410 EGR Valve Position Sensor Circuit Malfunction - Read Our Article on EGR Valve Codes For Help With This Toyota Check Engine Light Code

P1411 EGR Valve Position Sensor Circuit Range/Performance - Read Our Article on EGR Valve Codes For Help With This Toyota Check Engine Light Code

P1500 Starter Signal Circuit

P1510 Boost Pressure Control Circuit

P1511 Boost Pressure Low

P1512 Boost Pressure High

P1520 Stop Lamp Switch Signal Malfunction

P1565 Cruise Control Main Switch Circuit

P1600 ECM BATT Malfunction

P1605 Knock Control CPU

P1630 Traction Control System

P1633 ECM

P1652 Idle Air Control Valve Control Circuit

P1656 OCV Circuit

P1658 Wastegate Valve Control Circuit

P1661 EGR Circuit

P1662 EGR Bypass Valve Control Circuit

P1700 Vehicle Speed Sensor '2' Circuit Fault

P1705 Direct Clutch Speed Circuit Fault

P1765 Linear Shift Solenoid Circuit Fault

P1780 Park/Neutral Position Switch Malfunction (Only For A/T)

Back To Top Of Toyota Check Engine Light Codes Page

Mar 21, 2009 | 2002 Toyota 4Runner

Not finding what you are looking for?
2002 Toyota 4Runner Logo

Related Topics:

740 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...