Question about 1997 Chevrolet Suburban

1 Answer

I should use my flashing lights when I am going back? I think that is importante to send a warning to another drivers that I am moving back

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

Sure it is a good ideal some people put a back up beeper on the reverse light so it beeps when backing up. If you get one and install it be sure it is less than 90 Decbels to be legal. If you need help to wire it let me know it is quite simple to do.

Posted on Sep 28, 2009

  • Bruce Hathcock Sep 28, 2009

    Sure it is a good ideal some people put a back up beeper on the reverse light so it beeps when backing up. If you get one and install it be sure it is less than 90 Decbels to be legal. If you need help to wire it let me know it is quite simple to do.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hand brake lights do not come on


Hi Ashley:
Hand brakes are intended for keeping the vehicle from moving when it is parked.
If the lights were on when the vehicle was parked, eventually the battery would go dead.
Brake lights are intended to warn the driver's in following vehicles that you are slowing down and that you don't want them to crash into you.
All is good.
Cheers.

Oct 20, 2015 | Cars & Trucks

1 Answer

2008 Ford Explorer Eddie Bauer Driver Seat moves and light goes on while driving


Most likely a failing driver door latch internal contact switch , GEM module thinks it sees door open and kicks seat back and turns dome lite on. Use of a scanner to access GEM will show codes to verify issue.

Feb 21, 2014 | 2007 Ford Explorer Eddie Bauer

1 Answer

My check gauges light is on, oil hands goes over to zero, moves up, light goes off, when it drops back to zero, gauge light comes back on.


Well the warning light is supposed to come on if any of the gauges display a dangerous condition, such as no oil pressure.
You may have a faulty sending unit for the gauge, or a wiring problem, or the engine may actually be loosing oil pressure when the gauge drops.
You could replace the sending unit as a test, or have someone check the oil pressure with a mechanical gauge.

Dec 13, 2012 | 2001 Jeep Grand Cherokee

1 Answer

Audi tt x reg - the key fob is not working. Additionally, the hazard warning lights intermittently come on when i the engine. The hazard warning lights do not stop flashing and i often have to try...


this can be a big problem so will start on easiest first. and try to repair as going, the passenger door the problem with this could be the solenoid for the door lock. and or the switches in the lock. driver door has the same but is the master door. ie if you open door from unlocking at pass door it will only open this door, drivers side will open all doors. flashing hazards this could be because the alarm is not completely turned off this could be because of the doors, mainly the drivers side. try to find the fault with the door lock and get back to me when you have found the fault. you will need a meter to check for volts and the switches, check them as lock unlock from the inside and the key to make sure they working. dpd spray should be able to clean them if you can spray into the lock and housing that is plastic. give a good flush out after its working wipe up the mess from the spray and mear grease on the lock moving parts.

Jun 26, 2017 | 2000 Audi TT

2 Answers

After flat tire, tire pressure warning will not go out even after making sure pressure is at 44psi. How do I reset dash?


44PSI?? is that what your car recommends...


1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

Aug 14, 2009 | 2006 Hummer H3

1 Answer

Drivers side seatbelt connected When truck is


sensor in the seat belt bukle needs to be replaced

Aug 01, 2009 | 2004 Ford F150

1 Answer

Fuel warning light permanently on all the when


either the switch or sending unit is bad at the tank, or there is a hole in the float, which will keep it down all the time, i think it is the sending unit, wires either damaged or unpluged, any thing can get up there when driving of going off road. that is where i would start.

Jun 24, 2009 | 1991 Nissan King Cab

1 Answer

All warning lights flashing on dash of chevy trailblazer 2003. Runs fine all gagues go dark like truck is turned off but runs fine


All warning lights flashing on dash of my 2002 chevy trailblazer. Runs fine all gagues go dark and turn back on every now and then. Also the gagues all go to the right or stick half way like I am idling at 5000 and going at a speed of 60mph when I am sitting still. I am thinking it has something to do with my computer because the rest of the truck is working just fine.

May 18, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

Gages and warning lights jump and flash


Check the wire harness plugs in the back of the guage package... They might be loose and making and breaking connection when you hit a bump... Two upper, two lower screws normally on imports and domestics on the guage cluster...

Jan 07, 2009 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
1997 Chevrolet Suburban Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...