Question about 1997 Pontiac Grand Prix

Open Question

Cannot remove the license plate bulb to replace it

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 160 Answers

SOURCE: Change License Plate Light Bulb

you should be able to get to thru the trunk

Posted on Dec 10, 2008

Ad
c17hydro
  • 2984 Answers

SOURCE: how to change the license plate light on 2001 ford focus zx3

Take a thin blade screw driver and gently pry between the rubber seal and the metal and pop the light out, replaced the bulb and pop the light back in. works fine.

Posted on Mar 22, 2009

c17hydro
  • 2984 Answers

SOURCE: license plate bulbs on 98 Park Avenue

License Plate Lights Removal & Installation 1997 – 2000 To Remove:

License/backup Lamp Assembly


76707d9.gif

  1. Remove the rear compartment lid trim. (if necessary)
  2. Disconnect the license/backup assembly connector from the body harness.
  3. While removing the license/backup lamp assembly from the rear compartment lid, disconnect the harness grommet from the rear compartment lid.
  4. Remove the license lamp housing from the license/backup lamp assembly.
  5. Remove the license lamp bulb from the housing and socket.
To Install:
  1. Install the license lamp bulb into the socket and housing.
  2. Install the license lamp housing onto the license/backup lamp assembly
    • Torque the fastener to 18 in-lb (2 Nm).
  3. While holding the license/backup lamp assembly, install the harness grommet to the rear compartment lid.
  4. Install the license/backup lamp assembly
    • Torque the fasteners to 53 in-lb (6 Nm).
  5. Connect the license/backup assembly connector to the body harness.
  6. Install the rear compartment lid trim. (if necessary)

Posted on Jun 30, 2009

techbuster
  • 5081 Answers

SOURCE: 1999 Dodge Neon rear license Plate bulb

LICENSE PLATE LAMP BULB
REMOVAL

  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Posted on Oct 08, 2009

  • 179 Answers

SOURCE: How do I removed and replace the license plate

up under the license plate it changes like all other on your vehicle

Posted on Oct 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace licence plate bulb montero sport 2010


Remove license plate, remove screws and detach license plate pocket assembly. Rotate bulb holder, pull bulb straight out and replace.

Nov 23, 2014 | Cars & Trucks

1 Answer

How to replace License Plate Bulb '96 Jeep Grand Cherokee Limited


Hi Timmy:

Check this procedure from Repair manual...


LICENSE PLATE LAMP - REMOVAL
(1) Remove screws and license plate lamp visor from liftgate (Fig. 10).
(2) Remove bulb from lamp socket.

INSTALLATION
(1) Install a bulb in lamp socket.
(2) Position license plate lamp visor on liftgate and install screws (Fig 10).


4_28_2012_5_22_57_pm.jpg


Hope this helps.

Apr 28, 2012 | 1996 Jeep Grand Cherokee

1 Answer

Need to replace bulbs that lights license plate. License plate and light is part of trunk


raise trunk lid look on the inside behind your license plate light there should be access to the bulb there. You will see the wires going in to the bulb there will either be a flt plate that can be removed to access bulb or where the wires enter there will be a round socket that you can twist counter clockwise and remove the bulb socket for bulb replacement. hope this helps.

Jan 15, 2011 | 2003 Lincoln Town Car

1 Answer

I need to replace the bulbs above the license plate on my 2002 eldorado how do you replace them....get at the old bulbs


Hello: Remove the license plate, then remove the screws on the chrome piece behind the license plate and the you can access the bulbs.

Nov 24, 2010 | 1999 Cadillac Eldorado

1 Answer

How do i change the license plate bulb on a 2004 tb ls


here is the instructions on how to replace license plate bulbs.

Remove the 2 screws that retain the license lamp lens to the liftgate.

  • Remove the license lamp lens from the liftgate.
  • Remove the bulb (1) from the socket.


  • 8e7cf48.gifaba90ae.gif

    Oct 11, 2010 | 2004 Chevrolet TrailBlazer

    1 Answer

    License Plate Lamp Replacement on 1999 Cadillac Eldorado ETC. Where is the access point for replacing the licence plate lamps?


    Hello, remove the rear license plate, remove the housing where the license plate was mounted, now you can see how to replace the bulbs.

    Sep 05, 2010 | 1999 Cadillac Eldorado

    1 Answer

    License plate bulb needs replacing


    Remove license plate. Unscrew the screws on the underside of the bumper. Slide the lights back toward the trunk and then down through the opening. Unscrew bulb and replace with a new one.

    Reverse steps to reinstall the lights.

    Feb 06, 2010 | 2003 Chevrolet Impala

    1 Answer

    1999 Dodge Neon rear license Plate bulb


    LICENSE PLATE LAMP BULB
    REMOVAL
    1. Remove screws attaching license plate lamp to rear bumper
    2. Remove lamp from bumper.
    3. Remove bulb socket from lamp.
    4. Pull bulb from socket.

    INSTALLATION
    1. Install bulb into socket.
    2. Install bulb socket into lamp.
    3. Place lamp in position.
    4. Install screws attaching license plate lamp to rear bumper.

    Oct 08, 2009 | 1999 Dodge Neon

    1 Answer

    License plate bulb 99 alero


    remove the 2 license lamp screws from outside,above the lic.plate then from insidethe trunk pull up the lic.lamp housing and replace the bulb.it should pull straight out

    Apr 21, 2009 | Oldsmobile Alero Cars & Trucks

    1 Answer

    2002 license plate bulbs


    its real simple look at the license plates then look up you will see 2 screw per lamp / unscrew them and slide remove its a 194 bulb so get some ready then replace and put back / Please rate my response thank you very much

    Feb 01, 2009 | 2002 Toyota Avalon

    Not finding what you are looking for?
    1997 Pontiac Grand Prix Logo

    Related Topics:

    176 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Pontiac Experts

    yadayada
    yadayada

    Level 3 Expert

    77499 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8826 Answers

    Are you a Pontiac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...