Question about 2000 Isuzu Rodeo

1 Answer

I have marks aligned and i tried to started and still out of time

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,113 Answers

You need to take it to a trained mechanic for this fix. The cam pulleys turn three or four times to one turn of the cam shaft . You can bend valves too.

Posted on Sep 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

88 Honda prelude SI wont start?


U need to re-timed the engine. Check all four marks going across the two cam pully is lined up with the engine head surface.
Then check the crank pully alignment mark the single notche align to the mark on the timing cover

Apr 05, 2015 | 1988 Honda Prelude

1 Answer

I replaced timing chain wont start


Confirm the timing marks were aligned properly by manually rotate the crankshaft up until piston number one is on a compression stroke, try to do this twice and make sure that the timing marks should be aligned accordingly with piston number one in top dead centre.

Jul 10, 2014 | 2004 Nissan Nissan almera tino

2 Answers

On 2000 mazda protege 1.6 replaced water pump now won't start, thinking timing now out what is timing procedure?


i dont have a more detailed picture of setting the timing marks for the belt so i hope this helpsonetufshoppe_81.gif

Jan 30, 2011 | 2000 Mazda Protege

1 Answer

I have found the crankshaft marks but I cannot find marks to align the to over head cams on my car, the dohc are run from 1 wheel. I am trying to re-align the timing belt as i think they have gone off.


if it's a dual overhead cam then each head has two cams and two pully's, a single overhead cam engine has one cam and one pulley on each head. if the belt has more than 60,000 miles on it you should replace it. you need to find out if the engine is an interference engine or not to determine the level of damage caused if the belt has jumped or slipped. your overhead cam timing marks are usually on the cam faces and the backing plate behind the cam or sometimes there's two marks on the cam that you align with the surface of the head behind them. the first thing you need is a diagram of the belt routing and mark positions because timing marks are very important especially on an interference engine. starting or cranking an interference engine with the timing marks misaligned can bend all your valves or even punch holes in your pistons! so proper alignment is crucial, good luck.

Jan 02, 2011 | Mazda 323 Cars & Trucks

1 Answer

Set harmonic balancer to top dead centre,set cams to timing marks,engine will not start but turns over. Hyundai Terracan 2002


hi from uk assume you have renewed c/belt and balance shaft timing belt? if so? and sure your timing marks on cams and the c/shaftcog are correct ? the oil pump also correctly aligned with marks? and the balance shaft gear also has time marking ? want to run thro how and which marks you have aligned and at TDC No1 all belt/s have to be aligned ??

Dec 27, 2009 | Hyundai Sonata Cars & Trucks

1 Answer

2000 Daewoo. Lanos won't start after lining up timing marks


did you turn over any gears while belt was off to align timming marks?
if so did you encounter a resistance and forced the gear over with a bit more than normal force?
if so you could have bent valves which will cause back fire on start up run and dies then wont start again seen a few apprentices get caught by this from forgetting to align marks up before removal of belt or on assembly of head to block. then realising marks are out try to align and have bent valves.(there is a way to do this safely)
check compressions if very low in a couple or all cylinders valves are bent.

Jun 26, 2009 | 2000 Daewoo Lanos

3 Answers

I have changed the timing belt on a 99 Dodge Stratus with a 2.4 liter engine. All timing marks are aligned properly according to Haynes diagram and the engine will still not start. It tries to start


check your distributor position,double
check all marks again,make sure when u line up
the crank marks at #1 cyl. at compression and cam shaft marks!!

G

May 28, 2009 | 2001 Dodge Stratus

1 Answer

Can't adjust my timing


try aligning the timing marks again and mark the placement of the number one wire on the distributer housing then remove the cap and align the rotor with the mark then try to start it also it is important to be sure the marks were aligned properly sometimes they have to point together sometimes straight up etc. NOTE:if the valves are damaged you may not be able to start the vehicle even if you have change the timing belt

Apr 25, 2009 | 2001 Mazda Millenia

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

2 Answers

Timing marks for kia rio 2002 1.5l


Turn crankshaft so that timing marks on belt pulley are aligned with marks on engine . The 'I' on intake pulley is on top and the 'E' on exhaust pulley is also on top.Align crankshaft pulley with mark on engine.If your timing belt is broken then major damage to the engine has occored and kiss it good bye.

Jul 20, 2008 | 2002 Kia Rio

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...