Question about 2003 GMC Sierra

3 Answers

Winshield is cracked and needs to be replaced on my 2003 gmc sierra. I can get one cheap if I install myself. Is there anything outside the ordinary I should know?

Posted by on

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 114 Answers

Just the normal, good workmanship procedures. Make sure the part is the proper fit, the seating area is clean, a good sealant and wait before you move the vehicle for a proper cure of the sealant

Posted on Sep 20, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

Huh?, I just had an Autoglass shop replace my 2003 Sierra 2500HD windshield and it took him 1.5 hours, he cleaned up all the mess and disposed of all the waste. It cost $267.00 (Cdn) (which is about $230.00USD) for the windshield, and labour to install it. Don't know how much cheaper you can get than that and still have a 1 year garantee against leakage. And if he had made a mistake and cracked it during the installation, he would be the one to pay for the new one, not me.

I just can't see the benefit in doing this type of job oneself. Notwithstanding the fact that the windshield is now an integral part of the cabin and is crucial in a rollover for strength the risks just don't justify saving a couple of bucks. IMHO

Posted on Sep 24, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 45 Answers

Fairly easy install. pull door weatherstrip away from the a pillar post remove screws that attach side reveal mldgs. 2 screws on either side of cowl & plastic push pin in the center of cowl. remove rear view mirror, and cut the glass out, trim existing urethane down leaving a thin layer (1/16") to apply your new urethane adhesive to. prime any nicks to the pinchweld to protect from rusting and giving you a good surface to bond to. clean and prime glass. run urethane adhesive (I prefer Essex 400HV, like oe) set glass and re-install parts that you removed. allow time for cure (paying attention to safe drive away time for you region's temp, humidity). clean up and done! good luck

Posted on Sep 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know what transmission is in my 99 gmc Yukon. Or how to find out


Shop for need to know what trans... on Google


Refurbished 1999 Gmc Yukon Transmission ...
$1,199.75
JCWhitney.com Refurbished 2003 Gmc Yukon Xl 1500 ...
$1,529.73
JCWhitney.com Refurbished 2002 Gmc Yukon Transmission ...
$1,199.75
JCWhitney.com Search Results

    I need to find out what transmission is in a 1999 gmc sierra ...

    www.cargurus.com > Questions > GMC > Sierra 1500

    CarGurusApr 7, 2013 - I need to find out what transmission is in a 1999 gmc sierra 1500 pick up 4x4 extended cab. ... Good luck. if the transmission is bad and you KNOW that for a fact, just go ahead and pull it ... My trans went out yesterday and I found one and wantto make sure it fits before I buy it. ... Used GMC Yukon Denali".

    Is The Transmission In A 1999 Gmc Yukon And ... - CarGurus

    www.cargurus.com > Questions > GMC > Yukon Denali

    CarGurusAug 15, 2014 - Is the transmission in a 1999 gmc yukon and a 2000 Yukon Denali the same. ... Does anyone know where I can get a fairly cheap used motor from in or ...Need a good fairly cheap motor for my 99 Gmc Yukon Denali 5.7L V8.

Jan 26, 2016 | GMC Cars & Trucks

1 Answer

Proceedure for replacing 2003 gmc sierra brake back plate


I have a 2000 Sierra it has a one piece backing plate that was half rotted. I removed all hardware( caliper etc ) cut off old plate. I then bandsawed new one piece plate in half , attached two overlap tabs on the halves, and sprayed the outside surface with stoneguard spray to protect them. When you install the hardware the two halves will be held securely and the stoneguard will help to keep them from rotting off again.
Or...... do what the gmc engineers do , remove the rear differential cover drain the fluid, pull the axle shafts and replace the plates as one piece. About $100 extra in oil and gaskets. Thanks GMC..

Apr 14, 2009 | 2003 GMC Sierra 1500

2 Answers

Special wiring harness for new stereo in 2005 sierra


Yes u do....I have an 03 sierra and apparently they changed everything in 03.....the harness is over $100.....but u need it....and they dont sell a reg wiring kit from 03 and up....if it was an 02, then yes u could get away cheap......it has to do with the steering wheel switches

Jan 03, 2009 | 2003 GMC Sierra

Not finding what you are looking for?
2003 GMC Sierra Logo

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...