Question about 2000 Daewoo Leganza

1 Answer

Were is the crankshaft sensor on my 2000 daewoo leganza

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 80 Answers

To find the crankshaft sensor you will have to.
Remove the power steering pump if equipped,
Remove the a/c compressor,
Remove the a/c compressor mounting bracket bolt.
Remove the accessory mounting bracket.
Once you pull the a/c bracket out of the car you will see the
cranshaft position senor (CKP).
Remove the one bolt that hold it in place.
Gently rotate and remove.

Posted on Sep 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Daewoo leganza sx 1998


Th engine would not start.

Jun 01, 2012 | 1999 Daewoo Leganza

1 Answer

WHAT IS CORRECT TIMING MARKS FOR TIMING BELT INSTALLATION. 2000 NUBIRA 2.0 DOHC AND CRNKSHAFT MARKS. Thanks Joe


TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim_4.jpg
Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim2_3.jpg
Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim3_1.jpg
here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Feb 17, 2011 | 2000 Daewoo Nubira

1 Answer

How do you replace the camshaft position sensor on 2000 leganza?


This is covered by Daewoo under warranty. Contact DaewooUSA and they will send you instructions and warranty information. I had mine fixed under warranty in September, 2010. They paid for everything, new sensor, new wire, new fuse link.

Oct 27, 2010 | 2000 Daewoo Leganza

2 Answers

2000 daewoo leganza radiator fans not


there's a sensor on the radiator that tells the fan to come on a serten temp,replace that,there normally on the side,just release the clip and pull it out,make sure it cold before you remove it as the water will come out.

Dec 24, 2009 | 2000 Daewoo Leganza

1 Answer

Timing marks on a 2000 daewoo leganza


Your Daewoo has an 2.2L engine and it's an interfernce engine. Which if the timing belt pop it will bent valve's. To align timing mark's both intake and exhaust cam gear's have a mark, on backplate of gear's at 12 o'clock there a mark align both gear's to that. on crankshaft timing belt pulley has a noch on housing back of gear at the 6 o'clock there a v cut, align pulley to that. Good luck

Nov 18, 2009 | 2000 Daewoo Leganza

2 Answers

Engine managment light


found it at rear of sump on lefthand side also thanks for your help in solving engine management light it was the crankshaft sensor as suggested by someone on fixya

Jun 02, 2009 | 2000 Daewoo Leganza

1 Answer

Car does not start


try a crankshaft sensor

Mar 26, 2009 | 2000 Daewoo Leganza

1 Answer

Daewoo leganza 1998, speedometer is not working.


SPEEDOMETER (SPEEDO DRIVE) IS USUALLY LOCATED IN GEARBOX NORMALLY SCREWED IN SMALL BOLT YOU WILL PROBABLY FIND IT AT REAR END OF GEARBOX AS FOR RPM DIAL THAT IS USUALLY WORKED THROUGH CRANKSHAFT SPEED SENSOR BEFORE YOU GOCHANGING SPEEDO DRIVE MAKE SURE ITS NOT A BLOWN FUSE

Feb 13, 2009 | 2000 Daewoo Leganza

Not finding what you are looking for?
2000 Daewoo Leganza Logo

Related Topics:

429 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Marvin
Marvin

Level 3 Expert

83036 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...