Question about 1996 Chevrolet Corsica

1 Answer

Me 1996 gm 3.1 v6 will not start just back fires when cranking. changed timeing set ,coil packs , cam sensor

Posted by on

  • booter73 Sep 20, 2009

    changed timing chain & gears lined up properly

  • booter73 Sep 20, 2009

    rechecked. removed valve cover see that #46 valves not moveing

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 811 Answers

Check timing belt

Posted on Sep 20, 2009

  • chris quammen Sep 20, 2009

    buy manual, recheck timing 

  • chris quammen Sep 20, 2009

    is valve making contact with cam?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Isuzu 220le has no spark on cylinder 2&3 but continuous spark on 1&4. Single coil pack system and it back fires each time o crank. Changed HV cables and plugs but still not running


see if u are getting spark from the coil itself (fm 2& 3) It may be the coilpack itself, cam or crank sensor. Start w the coil.

Apr 10, 2017 | Isuzu Cars & Trucks

1 Answer

My Mitsubishi pajero 3.5 v6 is back firing I have change coil pack , cam and crank sen Ora,spark plugs. What could be the problem


getting to much fuel through injectors there is to much back pressure relieve the back pressure by what looks like a valve stem on the fuel rail and this should take care of it

Sep 08, 2014 | Mitsubishi Pajero Cars & Trucks

2 Answers

96 intrepid not fireing have tried resetting the timeing no codes were found new coil pack all connections r good what do i do next


i got a1996 dodge intrepid 3.5 L .the spark plugs 1,3,2 works but 4,5,6 do not work. i changed the spark plug wires, the coil ,the crankshaft sencer and the camshaft sencer.what else could cause this not to start?

Jan 19, 2010 | 1996 Dodge Intrepid

2 Answers

Changed coil pack that wasnt firing started fine


check the fire to the coil pack if it's present then check the pulse to the crank sensor

Jan 14, 2010 | 1999 Pontiac Firebird

2 Answers

2001 FORD TAURUS 24 VALVE DOHC MOTOR WILL NOT START


i have a 2001 taurus 24valve dohc 3.0 engne i have a bad coil pack what steps do i need to do to change the coil pack

Sep 07, 2009 | 2001 Ford Taurus

1 Answer

1996 Chrysler LHS not firing


First, check the ECM fuse in the power control module (it will be a yellow 20 amp fuse). Second, check the timing belt. You can pull out the cam sensor and look in the hole while someone cranks the motor. If the cam gear is not turning, the timing belt is broken. VERY IMPORTANT - when replacing the cam sensor, get a special adhesive pad from a Chrysler dealer that attaches to the bottom of the sensor to set the proper gap (cost about $2). Install the cam sensor until the pad touches the gear and tighten down the locking bolt. The pad will wear off in normal running. If the gap is not set correctly using this gapping pad, you won't start.

May 12, 2009 | 1996 Chrysler LHS

1 Answer

I am not getting any fire when starting the engine. I've changed the crank and cam sensors coil packs,ignition control module,plugs and wires. I did a diagnostic test on the car and it came up with PO122....


I had a 2002 dodge town and country that lost fire and found that a wire under the fuses box was broken this is the fuse box up front under the hood. I used a test light to see if power was going to coil pack I had a friend crank while i tested each outlet on plug that is when I traced it back to the fuse box. I hope this helps

Apr 28, 2009 | 1996 Oldsmobile 88

2 Answers

Have a 1991 buick lesabre 3800 v6, cant get to run, have had in a buick dealership replaced coil pack and icm, ran good for 2 then stopped, took back to dealership and the have been unable to find what is...


Check the ECM if it has the number 1228253 on it, this is what is wrong with it. Gm trashed all of these bad ecms. Get a 16198264 as they do not cause a cutting off problem . Get a delco ecm , aftermarket units will give trouble and may be a rebuilt 1228253 which is junk.

Apr 17, 2009 | 1991 Buick LeSabre

2 Answers

I cant get spark out of the coil pack


cam sensor fires the injectors to synchronise injector pulsing with the spark at the spark plugs.. U need to probably change the crankshaft sensor (around the crank pulley) as the crank sensor is what controls the ignition spark.
hope that does it.
:)

Jan 20, 2009 | 1996 Plymouth Voyager

Not finding what you are looking for?
1996 Chevrolet Corsica Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...