Question about Cars & Trucks

Open Question

I need a light lens for the outside light up forward on a 2006 18ft mallard

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Looking for an owners manual for a 1964 mallard drake camper

Type, '64 mallard drake camper owners manual' in your search box and hit search, if you haven't already. Other than that, I don't know?

Jan 01, 2016 | Cars & Trucks

1 Answer

How do you get the steps down on a 2013 mallard travel trailer

Hi Dustin:
Not sure about your Mallard but on one of my old trailers you had to push the steps in, then lift up. then pull out, and they would lower.
Sometimes the pivot points get really badly rusted and seize. That's where a good soak with WD-40, patience, and a small hammer (2 lb max) come in handy.
Last resort is to toss a rug on the ground and get under the steps so you can see how they are supposed to move. Then you'll be a happy camper (groan).

Nov 27, 2015 | Cars & Trucks

1 Answer

I have a 99 mallard fifth wheel I charged the

make sure inside and outside of battery posts are bright and shiney (clean) before putting together ,wires tight to clamps too

I had an experience years ago now where i thought i had bigger problems then i really did turned out to be just a dirty battery post , now im very serious about keeping them clean

Sep 11, 2014 | Cars & Trucks

1 Answer

I have a 1990 ford mallard motor home i installed a new fuel pump but not getting power back to the fuel pump.

You need to troubleshoot the wiring. I would start by checking the fuses. A lot of times when a pump fails it may short to ground and pop the fuse. Also make sure there are no breaks in the wire by checking for power with a test light or meter.

Jun 17, 2013 | Cars & Trucks

1 Answer

1994 escort lx has one piece llens on headlights-need to clean inside of it does it come off

Vy difficult to remove the clear lens from the housing. They are sealed to the housing however, it can be done. I'd use a heat gun but be careful not to melt the lens or housing.

Sep 10, 2012 | Chevrolet Equinox Cars & Trucks

1 Answer

Tail light lens replace

Not clear on make or model. Generally the tail light assembly is accessible from the trunck. May have to unscrew or remove bracket to gain access. Most lens covers are held in place by series of clips. Carefully remove clips and the existing lens should come out. May need second person to position replacement lens cover from outside while you secure from inside trunck.

Jan 26, 2012 | 2008 Chrysler 300

1 Answer


The only Mallard brand generators I could even locate are all. . . wind driven generators:
A Mallard generator

Sep 06, 2011 | 1985 Chevrolet Chevy

1 Answer

I have a 2006 Savana GMC 1 ton van that the both front turn signal housings need to be replace, how do you remove and install the housing?

Take a large (1/4" or wider) flat tippped screwdriver and insert in the outside edge of lens and gently pry off, there is a a plastic tip that holds the lens into the grill housing, once it is loose then move forward and outward. The inside just has a tab that holds the lens in. Mike Thompson ASE Master Tech. Fleetwash Atlanta Shop Manager

Jul 26, 2011 | 2006 GMC Savana

1 Answer

Need to change a tail light bulb left sideon a 2000 vw bettle

Unscrew the knob behined the light in the Boot / Trunk and the use a small screwdriver on the OUTSIDE of the light on the right handside as you look at the light in the middle on the outside. You will feel a little spring clip and as you push gently the light will pullout forward.
Go to the above link and you will get picture wise explanation for the same tail light bulb replacement. It has step by step picture explanation.

Oct 05, 2009 | 2000 Volkswagen Beetle

1 Answer

Rear tail light lens removal I need to replace the brake light bulb, but I do not see a way to remove the lens cover. I do not want to bust the one I have in order to fix the problem

Hello riggs791. My name is Roger and I will help you. Raise the lift gate. In the rain drip rail you will find two screws through the lens to the body. Remove the two screws. Carefully pull on the lens. What you are removing to get to the tail lamp bulb is the entire lamp. The front outside edge of the lens has two lock in clips. Once you have the lamp loose turn it over and unlock the socket and replace the light. Reverse to reinstall the lamp.
Should you need further help please just ask. Please rate the quality of your answer. This way we know the answer helped. Thank You for using Fix Ya. Roger

Sep 26, 2009 | 1999 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22408 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides