Question about Hyundai Tiburon

1 Answer

How do I change the timing belt on a 2003 Tiburon

Posted by on

  • rdanunz Sep 16, 2009

    This does not show the timing belt replacment it shows the accessory belt replacement. I have the 4 cyl engine. Thanks anyway

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 17,970 Answers

2003 Hyundai Tiburon 2.7L MFI DOHC 6cyl

Inspection
Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.
Removal & Installation

  1. Raise and support the vehicle.
  2. Remove the engine splash shield.
  3. Rotate the drive belt tensioner clockwise to release the drive belt tension.
  4. Remove the drive belt from the alternator.
  5. Slowly release the drive belt tensioner.
  6. Remove the drive belt from the accessory drive pulleys.
To install:
  1. Install the drive belt to the accessory drive pulley.
  2. Rotate the drive belt tensioner clockwise.
  3. Install the drive belt to the alternator.
  4. Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.
  5. Slowly release the drive belt tensioner
  6. Install the engine splash shield.
  7. Lower the vehicle.
How do I change the timing belt on a 2003 Tiburon - b3e0cbe.jpg

Fig. Accessory drive belt routing-3.0L and 3.5L engine


4a6b54d.jpg

Fig. Accessory drive belt routiHow do I change the timing belt on a 2003 Tiburon - 3b0d2d5.jpg 2.7L engines


3b0d2d5.jpg

Fig. Accessory drive belt routing-2.0L enginHow do I change the timing belt on a 2003 Tiburon - 508cf9b.jpg />
6d43bf5.jpg





Fig. Accessory drive belt routing-3.0L engine


99b1d12.jpg

Fig. Accessory drive belt routing-2.5LHow do I change the timing belt on a 2003 Tiburon - 3e72758.jpg />

97529b0.jpg
Fig. Accessory drive belt routing-2.4L engines


5cd1383.jpg

Fig. Accessory drive belt routing-1.8L and 2.0LHow do I change the timing belt on a 2003 Tiburon - 4081274.jpg />

3e72758.jpg

Fig. Accessory drive belt routing-1.5L engine


2aafa70.jpg

Fig. Accessory drive belt routing-2.4L engines


aa6cd2c.jpg

Fig. Accessory drive belt routing-2.0L engines


4081274.jpg

Fig. Accessory drive belt routing-1.5L engine


I hope help you with this (remember rated this help) Good luck.

Posted on Sep 15, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
MNfisherman
  • 11896 Answers

SOURCE: 03 hyundai tiburon serpentine belt change

You can go to autozone.com and register for free for free online repair manual for your vehicle. Also google images have pics. There are also more manuals here:
http://manualspace.com/manual/search/89-toyota-celica-gt-repair-manual-online-pdf.htm

Posted on Feb 06, 2010

jagjeffery
  • 318 Answers

SOURCE: 2003 Tiburon Timing Belt Replacement

the timing belt is not due to be changed until 120,000 miles i cant promise but you could make it to 150,000 but i wouldnt go much farther then that unless it wasnt changed at 60,000 if that is the case you are on barrowed time you need the belt changed as soon as possible.

Posted on May 30, 2009

  • 11 Answers

SOURCE: oil change, 2003 tiburon v6

Read all beffore starting. get all you need and get prepare beffore starting so you wont say any big word. Maybe have some safety glasses and never put youself on the way the oil would go out.
Buy yourself a 4.4L of new 10W30 motor oil, a oil filter, a little bucket of about 8" high and 24" round set of ratchett finaly some towel (for cleaning your tools and your hands if oiled by the old oil). Wait the motor to be cold. If you can, jack it a little bit just for you to be more comfortable under it. Better if you have ramp to put the front of the car on it and dont forget to put some safety like small candel and a tire stpper with the hand-brake on.
Go under the car, locate the oil pan and it's pug. Get the good size key or rattchet for the plug. Put you bucket under the plug, in line of the oil comming out, about 8 inches from the plug. Now unscrew the plug.... it will be a bit dirty and replace the buckey in line with the dirty oil if needed. When empty (about 10 minutes) get the oil cap on top of the motor out, go back under the car put the oil pan plug back (don't forget the washer and don't over tite it) , unscrew the old oil filter (watch for oil comming out from it also). With your finger, put some old oil on the rubber ring of the new oilf fliter and screw it in place of the old one "by hand", don't turn too hard, about half turn after the rubber touched the motor. Put the new oil in (where the oil cap on top-front of the motor was).. all the 4.4L. (watch for not putting oil all over, it will smell as hell when driving until it will all burn). Put the oil cap on. Recheck the filter, the oil pan plug and the oil cap. If all ok, Start the motor for 5 minutes but stay parked. Check the sound of the motor, it should go nicely ( by the way, get a full memory of this nice sound, it could alert you of somehting wrong if it dose not sound like this one day). Get you tools and the bucket from under the car, recheck the oil filter and the oil pan plug. If no oil is dripping, stop the car, get it down, get all things clear and clean. You can put the old oil in the can where was the new one beffore the job and get it back to your garage so they recycle it. The filter is gooing to the garbage. That's it. If not in a hurry and take your time with some good music and a coffee, you can do it in 20-45 minutes.
2-

Posted on Aug 02, 2009

SOURCE: need manual to change timing belt in 2003 tiburon

Check with local junk yards or try on Ebay they have some manuals also.

Posted on Sep 24, 2009

tinualbinale
  • 436 Answers

SOURCE: need timing belt diagram for

The timing belt diagrams are listed in detail with figures and procedure to remove them.

REPLACING TIMING BELT ON A 2003 HYUNDAI TIBURON 2.7L V6

1. Remove passenger side headlight via the 3 10mm screws holding it in place and disconnect the turn signal and main harness

2. Remove passenger side tire

3. Remove the splash guard via 2 10mm screws at the top of the guard

4. Remove the 2 17mm bolts and 2 17mm nuts from motor mount bar

5. You may have to separate the mount bar from the motor via either a chisel or flathead screwdriver and a hammer ( support engine via a jack and a piece of plywood under oil pan )

6. Use a 3/8 ratchet ( or a long breaker bar would work better ) to remove the serpentine belt ( remember the route ). Disconnect the power steering hose from the pump and secure back with a zip tie. Remove the power steering pulley with a pry bar and 19mm socket.

tinualbinale_2.gif
7. Hand turn the crankshaft via a 22mm socket to TDC ( top dead center, marked on lower timing belt cover )

8. Remove the serpentine belt tensioner via 2 12mm bolts on each side

9. Remove the upper timing belt cover via 7 10mm screws

10. Remove crankshaft pulley ( 22mm ) with an air impact gun ( an electric one will work too )

11. Remove lower timing belt cover via 4 more 10mm screws



tinualbinale_3.gif

12. Remove the motor mount from the block via 3 14mm bolts and 2 12mm bolts ( there is a 12mm holding the oil dipstick bracket towards the front of the car )

13. Remove the auto tensioner via 2 12mm bolts

tinualbinale_4.gif

14. Remove the timing belt
tinualbinale_5.gif

15. Make sure your timing markings are correct...

There is one marking on each cam gear and on the heads ( head markings are small, look closely...try wiping the edge of the head down with a rag and some brake cleaner to bring it out more ) They are also pictured in last pic.

When the crankshaft is in the TDC position, the cam gear markings should both line up at the same time with the head markings

Adjust if necessary, use a 17mm socket to turn cam gears to correct position

16. Install new timing belt ( as you install it, make sure to keep a little tension on the belt as you route it )

17. Install new auto tensioner and pull pin

18. Install just the lower timing belt cover

19. Install the crankshaft pulley

20. Hand turn the crankshaft atleast 5 times to verify the timing markings are lining up properly ( all should line up at the same time when the crankshaft pulley mark is in the TDC position )

21. Remove crankshaft pulley

22. Remove lower timing belt cover

23. Reverse steps 12 - 1

You can refer the videos below for further assistance.Your valuable feedback would be appreciated.Thanks for choosing Fixya.


Posted on Jun 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 tiburon and I need to know if its a valuve clearence engine or not


are you asking if its a interference or NON INTERFERENCE MOTOR?? did you blow the timing belt off??

Sep 09, 2011 | 2003 Hyundai Tiburon

1 Answer

03 hyundai tiburon serpentine belt change


You can go to autozone.com and register for free for free online repair manual for your vehicle. Also google images have pics. There are also more manuals here:
http://manualspace.com/manual/search/89-toyota-celica-gt-repair-manual-online-pdf.htm

Feb 06, 2010 | 2003 Hyundai Tiburon

1 Answer

Need manual to change timing belt in 2003 tiburon - 6 cyl


Check with local junk yards or try on Ebay they have some manuals also.

Sep 24, 2009 | 2003 Hyundai Tiburon

1 Answer

2003 Tiburon Timing Belt Replacement


the timing belt is not due to be changed until 120,000 miles i cant promise but you could make it to 150,000 but i wouldnt go much farther then that unless it wasnt changed at 60,000 if that is the case you are on barrowed time you need the belt changed as soon as possible.

May 29, 2009 | 2003 Hyundai Tiburon

1 Answer

2003 Tiburon GT, RPM's drop way down and idles rough at stop's?


More maintenance history needed. Oil changed regularly, timing belt replaced at 60 K miles, Engine air filter & intake air hose inspection?
Causes of the problem you describe are many. Recommend you have a technician check your throttle position sensor for any bad spots in the potentiometer... most likely cause when there is NO Check Engine light.

Mar 28, 2009 | 2003 Hyundai Tiburon

1 Answer

Problem with 2003 Tiburon water pump


its driven by the timing belt,it also has a plastic pulley that breaks away from the drive,silly idea but lots of cars use it

Feb 28, 2009 | 2003 Hyundai Santa Fe

1 Answer

Airbag light is on - 2003 Tiburon


section_closed.gif 2003 HYUNDAI TIBURON Recall ID from NHTSA: 02V290000 Auto Recall Date: NOV 05, 2002 Vehicle Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY Model Affected TIBURON Estimated Vehicles Affected: 7382 Recall Details Auto Recall Date: NOV 05, 2002

Vehicle Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY Estimated Vehicles Affected: 7382 Model Affected2003 HYUNDAI TIBURON

2003 Hyundai Tiburon Defect Summary:ON CERTAIN PASSENGER VEHICLES, THE DRIVER SEAT BELT BUCKLE WIRING COULD BE DAMAGED BY INTERFERENCE WITH THE DRIVER SEAT CUSHION HEIGHT ADJUSTER MECHANISM.

Defect Consequence:DAMAGED DRIVER SEAT BELT BUCKLE WIRING COULD CAUSE THE SEAT BELT WARNING LAMP OR THE SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG WIRING LAMP TO ILLUMINATE. IT COULD ALSO CAUSE THE AIR BAG FUSE (CAVITY NUMBER 5) TO OPEN, PREVENTING AIR BAG DEPLOYMENT. NONDEPLOYMENT OF AN SRS AIR BAG IN A CRASH WHERE AIR BAG DEPLOYMENT IS WARRANTED COULD INCREASE THE RISK OR SEVERITY OF INJURY IN A CRASH.

Remedy:DEALERS WILL INSTALL A NEW DRIVER SEAT BELT BUCKLE, IF NECESSARY, AND WILL PLACE A PROTECTIVE COVER OVER THE DRIVER SEAT BELT BUCKLE WIRING TO PREVENT DAMAGE FROM OCCURRING. OWNER NOTIFICATION BEGAN ON MARCH 24, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT HYUNDAI AT 1-800-633-5151.

Estimated Vehicles Affected: 7382

Notes: HYUNDAI MOTOR COMPANY 056

Dec 07, 2008 | 2003 Hyundai Tiburon

2 Answers

2003 hyundai tiburon 4cyl wont start


I know there is no imoblizer on canadian modles not shure about american if there is that would be my first thing to look for
other then that you have changed alot of parts but have u checked any of the fuses or relays and dubble check that every thing is plugged in correctly if all that is good u have a wirring problem

Oct 19, 2008 | 2003 Hyundai Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

4,366 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

84027 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22483 Answers

Jonah Oneal

Level 3 Expert

14059 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...